Search Documents

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By W. E. Bergman, P. G. Carpenter, H. B. Fisher

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By P. G. Carpenter, H. B. Fisher, W. E. Bergman

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By M. R. Tek, R. L. Nielsen

The scaling laws as formulated by Rapoport relate dynamically similar flow systems in porous media each involving two immiscible, incompressible fluids. A two-dimensional numerical technique for solving the differential equations describing systems of this type has been employed to assess the practical value of the scaling laws in light of the virtually unscalable nature of relative permeability and capillary pressure curves and boundary conditions. Two hypothetical systems — a gas reservoir subject to water drive and the laboratory scaled model of that reservoir — were investigated with emphasis placed on water coning near a production well. Comparison of the computed behavior of these par ticular systems shows that water coning in the reservoir would be more severe than one would expect from an experimental study of a laboratory model scaled within practical limits to the reservoir system. This paper also presents modifications of the scaling laws which are available for systems that can be described adequately in two-dimensional Cartesian coordinates. INTRODUCTION Present day digital computing equipment and methods of numerical analysis allow realistic and quantitative studies to be carried out for many two-phase flow systems in porous media. Before these tools became available the anticipated behavior of systems of this type could be inferred only from analytical solutions of simplified mathematical models or from experimental studies performed on laboratory models. To reproduce the behavior of a reservoir system on the laboratory scale, certain relationships must be satisfied between physical and geometric properties of the reservoir and laboratory systems. Where the reservoir fluids may be considered as two immiscible and incompressible phases, the necessary relationships have been formulated by Rapoportl and others.2-5 Rapoport's scaling laws follow from inspectional analysis of the differential equation describing phase saturation distribution in such systems. It will be recalled that these scaling laws presuppose three conditions: (1) the relative permeability curves must be identical for the model and prototype; (2) the capillary pressure curve (function of phase saturation) for the model must be linearly related to that of the prototype; and (3) boundary conditions imposed on the model must duplicate those existing at the boundaries of the prototype. These three requirements seldom if ever can be satisfied in scaling an actual reservoir to the laboratory system because: (1) The laboratory medium normally will be unconsolidated (glass beads or sand) while the reservoir usually is consolidated. Relative permeability and capillary pressure curves are usually quite different for consolidated and unconsolidated porous media. (2) The reservoir usually will be surrounded by a large aquifer which could be simulated in the laboratory only to a limited extent. (3) Wells present in the reservoir would scale to microscopic dimensions in the laboratory if geometric similarity is to be maintained. In view of these considerations, rigorous scaling of even a totally defined reservoir probably would never be possible. The purpose of this paper is to assess the practical value of the scaling laws in the light of the unscalable variables. This has been done by carrying out numerical solutions in two dimensions to the differential equations describing the flow of two immiscible, incompressible fluids in porous media for a field scale reservoir and a laboratory model of that reservoir. While both the reservoir and the laboratory model were purely fictional, each has been made as realistic and representative as possible. The field problem selected as the basis for the investigation was an inhomogeneous, layered gas reservoir initially at capillary gravitational equilibrium and subsequently produced in the presence of water drive. The laboratory model of this reservoir was designed to utilize oil and water in a glass bead pack. The numerical treatment employed was similar to that of Douglas, Peaceman and Rachford6 and it included both capillary and gravitational forces as

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By Joseph P. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies.

Jan 12, 1950

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By D. Havlena, A. S. Odeh

The use of the straight-line method of solving the material balance equation is illustrated by means of six field cases. Also, the application of statistical criteria to arrive at the most probable answer is shown. The theory underlying the straight-line method of solution and the applicability of the statistical criteria was presented in a previous paper.' The field cases include saturated and undersaturated oil reservoirs with and without water drive. The aquifers discussed are: limited radial, infinite radial, very small aquifer and infinite linear. The field cases also include a gas reservoir producing under water drive. INTRODUCTION In a previous paper,' the authors presented the theory underlying the solution of the material balance as an equation of a straight line. The appropriate equations for various material balance cases as well as the methods of analysis and interpretation with comments and discussion were also included. To illustrate the various theoretical cases treated previously, five field cases are analyzed in this paper by employing the straight-line method of solving the material balance equation (MBE) and one example previously published is referred to. The use of statistical criteria to arrive at the most probable answer is also shown. All the field examples presented, except Case 2, are excerpts from complete reservoir studies. To illustrate the method, only sections specifically dealing with the material balance principles are included. Additional geologic information and basic data are reported to better acquire an understanding of the cases and thus to better follow the reasoning that suggested the successful application of the straight-line method of solving the MBE. The six cases are: (1) saturated reservoir, small gas cap, limited aquifer; (2) saturated reservoir, very small gas cap, infinite aquifer; (3) undersaturated-saturated reservoir, very small aquifer; (4) highly undersaturated reservoir, no water drive; (5) high undersaturated one-well reservoir, limited aquifer; and (6) gas reservoir, infinite linear aquifer. THE D4 SAND, GUICO FIELD, VENEZUELA The D, sand, which was discovered in 1943, is presently in a depleted state. Since its discovery it has produced under water drive, gas-cap-gas expansion, and solution gas drive. In Nov., 1947, water injection was initiated to arrest further pressure decline. When discovered, the D, sand was a saturated reservoir with a gas cap /oil zone volume ratio m estimated volu-metrically at 0.0731, an average permeability of 500 md, a porosity value of 25 per cent, and an oil viscosity at reservoir conditions of 0.3 cp. The volumetrically determined stock-tank oil initially in place was 23.1 million bbl. The volumetrically weighted physical data and production data available until Nov., 1953 are reported in Table 1. In Ref. 1, the effects on the straight-line plot of various values of ro/r for a constant ?to, or of various dimen-sionless times for a constant r8/r10 were theorized and were illustrated in Fig. 3A of that reference. In this field case, the previously theoretically predicted effects are established. Thus, the MBE calculations using Eq. 3c of Ref. 1 were performed for various r6/r10 and dimension-less time values. Eq. 3c of Ref. 1 is:

Jan 1, 1965

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

By Craig E. Saporito

INTRODUCTION Freeport-McMoRan Inc. has been very active recently with two major discoveries and its restructuring activities. This paper describes Freeport-McMoRan's businesses, the two major mineral discoveries, and exciting opportunities within the oil and gas operations. BUSINESS ACTIVITIES Freeport-McMoRan is the largest and one of the lowest cost fully integrated U.S. phosphate fertilizer producers. It is the second largest domestic Frasch sulphur producer. Freeport- McMoRan will become the largest domestic producer of Frasch sulphur when its Main Pass Block 299 sulphur deposit reaches full production in 1993. Furthermore, it is the largest transporter of sulphur produced by others. Its oil and gas activities rank among the largest U.S. independents in terms of production and proved reserves. The copper/gold operations in Indonesia are among the world's lowest cost. When expansion operations reach full capacity levels in 1992, the Indonesian copper/gold complex will be the fifth largest copper operation in the world. Operations are divided into three business segments that include: 1. Agricultural minerals, incorporating sulphur, phosphate rock and phosphate fertilizer activities; 2. Energy, including oil and gas activities; and 3. Metals, incorporating copper, gold and silver operations in Indonesia. In early 1989, Freeport-McMoRan announced the discovery of two world-class ore bodies; a sulphur deposit off the coast of Louisiana on Main Pass Block 299, and a copper/gold deposit -- the Grasberg in Indonesia -- approximately two miles away from the existing Ertsberg East operations. As a result of these major discoveries, Freeport- McMoRan decided to carry out a restructuring program. Its purpose was to sell $1.2 to $1.5 billion of non-strategic assets. Debt levels and associated interest expenses will be significantly reduced, and general and administrative expenses will be reduced, which will place Freeport- McMoRan in an excellent position to fund the development of the Main Pass Block 299 sulphur discovery, the Grasberg discovery, and oil and gas discoveries. This restructuring program also will allow Freeport-McMoRan to achieve the greatest future value for shareholders by focusing on its principal businesses (Figure 1). Strategic Restructuring • Sell $1.2 - $1.5 Billion Of Non-Strategic Assets • Significantly Reduce Debt • Significantly Reduce G&A • Fund Development Of Main Pass & Grasberg • Stronger Company; Positioned For Future Growth • Focus Is On Principal Businesses: - Sulphur/Phosphate Fertilizers - Indonesian Copper/Gold - Oil And Natural Gas Figure 1 - Strategic Restructuring AGRICULTURAL MINERALS Main Pass Block 299 Discovery The Main Pass Block 299 discovery has a proven reserve of 67 million long tons of recoverable sulphur. This is the largest known Frasch sulphur deposit in North America. The discovery increased Freeport-McMoRan's sulphur reserves more than five-fold, and is synergistic with the company's phosphate fertilizer assets. The

Jan 1, 1990

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1'2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1'2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Cyril Stanley Smith

Somewhat over ten years ago the author described studies1'2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase boundary was accepted as substantially correct, even by later investigators3 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems5-9 without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese-silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced1' to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polarized light and asserted that a new phase, not cubic, should be placed in the diagram .adjacent to alpha. Sautner,l3 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his diagram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4 The thermodynamic impossibility of Sautner's diagram and the paucity of experimental data left the exact location of the new phase field most uncertain, although his work proved beyond doubt that an additional noncubic phase exists. Because of the industrial importance

Jan 1, 1940

By Cyril Stanley Smith

Somewhat over ten years ago the author described studies1'2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase boundary was accepted as substantially correct, even by later investigators3 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems5-9 without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese-silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced1' to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polarized light and asserted that a new phase, not cubic, should be placed in the diagram .adjacent to alpha. Sautner,l3 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his diagram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4 The thermodynamic impossibility of Sautner's diagram and the paucity of experimental data left the exact location of the new phase field most uncertain, although his work proved beyond doubt that an additional noncubic phase exists. Because of the industrial importance

Jan 1, 1940

By D. K. Crampton

Internal stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A resume of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking. Certain agents, particularly mercurous salts, mercuric salts and ammonia salts, have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent. zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alpha-beta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By D. K. Crampton

INTERNAL stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A résumé of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking: Certain agents, particularly mercurous salts, mercuric salts and ammonia salts; have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alphabeta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe 'limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.1

Jan 10, 1953

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By T. A. Read, H. M. Otte

THEORETICAL analysis by Wechsler, Lieberman and Read of the crystallography of martensite formation has shown that the requirement for the existence of a macroscopically undistorted plane between austenite and martensite permits a calculation of the indices of the habit plane of the marten-

Jan 1, 1958

By W. H. Howard

As the result of a series of analyses and volume determinations of gases discharged from the converters at the Garfield Smelting Co.'s smelter at Garfield, Utah, it was found that a considerable amount of lead fume was escaping from the stacks of the converter plant, and that if this lead could be recovered at a reasonable expense an attempt should be made to collect it. Two methods suggested themselves: (1) filtration through bags; (2) electrical precipitation of the condensed fume by a Cottrell plant. Filtration through Bags Tests were made in filtering converter gases through the ordinary woolen bags of lead-smelter bag houses to determine how long such material could withstand the corrosive action of the gases. While blowing on white metal only, the fabric was usually destroyed in 10 to 14 hr. In tests conducted in filtering gases when blowing on matte or slagging stage exclusively and when relatively considerable lead was being volatilizcd, bags in one instance lasted 60.5 hr. It therefore was evident that the Garfield converter gases did not contain in themselves sufficient neutralizing elements for the purpose of direct bag filtration, even during the slagging stage. Such results were more or less anticipated, but it was thus proved that under all conditions of blowing Garfield mattes a very considerable amount of neutralizing agent, zinc oxide or lime, or both combined, as in the Sprague process, would be required to render bag filtration possible. Again, owing to the constantly changing quantities of SO3 from a given battery of converters, depending on the number blowing at a given time and on the stages of the blow, it would be practically impossible to feed automatically the required amount of neutralizer. In order to safeguard the bags sufficient neutralizer would have to be continuously added to meet the maximum SO3 output, thus wasting neutralizers and giving an undesirably diluted final product. Such a condition is entirely different

Jan 1, 1915