Search Documents

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes hack well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948. Summary Of the eight million tons of coal mined in the two states in 1947. ap- proximately two million tons were washed in wet washing plants, using concentrating tables or jigs. The one table plant accounted for 70 pct of the output of washed coal, and two large Baum jig plants accounted for an additional 26 pct, leaving only a small residual tonnage to be accounted for by other types of jigs The necessity for washing coal is occasioned by the desire or necessity of reducing the ash content of the coals— sulphur is not a problem in this area. All washeries, except the table plant, are at or near the tipple, hence wash only one kind of coal. At the table plant a large number of different coals are washed. Only at the table plant is there any occasion for drying any considerable quantity of fine coal— other plants size and/or dewater on shaking screens. The results of washing at the smaller plants are judged by the number (or lack) of complaints about the quality of the washed coal. This is probably as good a system as can he devised for small, intermittent operations. The efficiency of the Baum jig ap-pears to be quite high. This is to be expected as long as the automatic control of the refuse gate operates properly. The efficiency of the concentrating table is not as high as that of the Baum jig, especially when the "difficulty" of washing is taken into consideration. When dealing with coals in which the "bone" is larger than the "coal," the table appears to be at a definite disadvantage, because of its sizing action.

Jan 1, 1950

those who are to lie in the torn fields of France. Today we read of Lieut. William Hague, whom we said good-by to hardly more than a month ago-—so clean, ao young, so strong—who, abandoning the professional career in which he had won such commendation and which held for him such promise, leaving his wife and his little boy to whom he was so dear, answered at once the call for men of his training, and is now dead "in the service of his country." There are many friends of that courtly and dignified gentleman James D. Hague who recall, both here and in Stockbridge, the parental pride in the promising lad of such a little time ago—the eager schoolboy at Milton, the rather grave youth at Harvard, his entry into new experiences in the Western mining world, and who, seeing him during his stay at Camp Upton, realized that the old Puritan stock was still sound and true—and now with him the struggle is over and the sacrifice made. Captain William Teasdale Hall Captain Hall, who was admitted to Junior Membership in the Institute in 1915, while still a student of mining at the University of Toronto, was killed in action in France on May 19, 1917. Captain Hall was born in Toronto in 1893, and received his academic training at Harbord College, from 1908 to 1911, when he entered the University of Toronto, School of Practical Science. During the three summer vacations of his university course, he was employed by the O'Brien mine at Gowganda, next by the McIntyre Mining Co., at Porcupine, and finally by the Mines Branch of the Geological Survey, which was conducting magnetic surveys to the north of Port Arthur. When war was first declared, Mr. Hall endeavored to join the artillery as an officer, and for the purpose secured a provisional lieutenancy with a Hamilton battery, but he did not receive an overseas appointment, and on being graduated as a mining engineer in 1915, he was offered a position in Chile, which he accepted. He left Toronto on May 27, 1915, and was engaged in Chile as a mining engineer for nearly a year. In the latter part of April, 1916, he decided to offer himself again for service at the front. He crossed the Andes and sailed for LiverpooI, where he landed on May 13, 1916. On May 27, 1916, Captain Hall was given a commission as a lieutenant in the Royal Flying Corps, 21st Squadron. He went to the front on Sept. 1, 1916, and remained there continuously. His

Jan 1, 1920

By J. J. Gilman, T. A. Read

FOLLOWING the deformation 01 zinc monocrys-tals, sharply bent basal planes are observed near several types of inhomogeneities. Three of these in-homogeneities have characteristics which are quite regular so that they can be studied and analyzed. These are compressive kink bands, "deformation bands," and the inhomogeneities near end restraints. The present paper describes experiments in which "deformation bands" were artificially produced, and bend plane phenomena are discussed in terms of dislocation theory. Also, two new bend plane phenomena are described. The importance of bend plane phenomena in the deformation of crystals is not widely recognized. Many phenomena may be explained in a manner similar to the discussion in this paper. Jillson1 has pointed out that the "punching effect" in zinc is a bend plane phenomenon and is not caused by prismatic slip.' Bowles3 has suggested that they may be involved in diffusionless phase changes. Cahn4 has discussed the role of bend plane formation in the polygonization of zinc. Experimental Work Tensile Kink Bands: Because of the geometrical similarity between "deformation bands" and "kink bands" (compare Fig. 1 of this paper with Fig. 1 of the paper by Hess and Barrett"), the band shown in Fig. 1 of this paper will be called a "tensile kink band," and that shown by Hess and Barrett will be called a "compressive kink band." It is felt that the term "deformation band" should be reserved for banded structures in polycrystalline materials such as iron." Tensile kink bands seem to form spontaneously in aluminum crystals deformed by tensile loading.7-10 In zinc and cadmium crystals they do not form in good, carefully loaded specimens.'." However, tensile kink bands can be produced artificially in zinc crystals. The present authors did this by scratching one of the flat surfaces of triangular crystals transversely with a sharp needle. Natural tensile kink bands caused by inhomogeneities sometimes appeared in deformed crystals which were identical in appearance with the artificially produced ones. Zinc monocrystals were grown by the Bridgman method in graphite molds. Chemically pure zinc (99.999+ pct Zn) was used and the molds were sealed inside evacuated pyrex tubes during growth. The crystal cross sections were equilateral triangles with a typical base of 0.210 in. The artificial kink band shown in Fig. 1 is typical of tensile kink bands in zinc. The band lies between two bend planes which run from upper right to lower left and is inclined oppositely to the slip bands which are sharply bent at the two bend planes. The general form of the artificial tensile kink bands was independent of the scratch depth (1 to 5 mils deep) and also independent of which side was scratched. These variables did cause variations, however. Deep scratches produced more localized kink bands than light scratches. Also, if the angle between the slip plane traces and a transverse scratch varied appreciably among the three sides, then localization of the resulting kink bands also varied. Furthermore, if the slip direction lay nearly parallel to the scratched side, the band was more developed near the scratched side than at the opposite edge. Scratches produced tensile kink bands for crystal orientations from xo = 15" to x, = 75". Fig. 2 shows a scratched crystal after deformation. One triangular side lies in the plane of the photograph. The right hand tensile kink band was produced by a transverse scratch on the upper right side. The next two kink bands were the result of scratches on the front surface. The kink band at the left was caused by a scratch on the lower back side. All four bands have the same general form. A longitudinal scratch was also made on the crystal shown in Fig. 2 to determine the effect of a scratch on the critical shear stress. The critical shear stress of the scratched region was 33.9 g per sq mm compared to 24.4 g per sq mm for the un-scratched region above it. Fig. 3 shows Laue patterns of the crystal shown in Fig. 2. Fig. 3a shows the pattern of the undeformed crystal. The orientation was x, = 21°, A, = 31". After deformation, Fig. 3b was made of the homogeneously deformed portion of the crystal. The spots are compact but split into two halves. This region was elongated 45 pct and its orientation was x = 14", X = 20"; the sine law predicts x = 14", A = 20.5". Fig. 3c was taken near the center of the middle tensile kink band of Fig. 2. The pattern shows a range of orientations and polygonization in this region. The spread in orientation was due to the fact that the basal planes were curved (see Fig. 1) rather than flat as in the ideal case. Some may also have been the result of elastic distortions and "local curvatures." The orientation range was x = 23" to 32", A = 30" to 42". It is apparent from Fig. 3 that the material inside and outside the kink band rotated in opposite directions with respect to the tension axis during deformation. The orientation calculated from the ideal configuration of Fig. 9,

Jan 1, 1954

By Norman F. Patton

The subject assigned is so broad that thorough discussion is well-nigh impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. Avenues of Distribution Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the different communities he serves. His business includes all sizes of anthracite. The third, and by far the most general method, consists in selling to retail dealers, shipments being made direct from the breakers to the yards of the dealers. In large consuming areas, such as the metropolitan districts of New York or Philadelphia, one operator may sell to several

Jan 1, 1936

By Norman F. Patton

The subject assigned is so broad that thorough discussion is well-nigh impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. Avenues of Distribution Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the different communities he serves. His business includes all sizes of anthracite. The third, and by far the most general method, consists in selling to retail dealers, shipments being made direct from the breakers to the yards of the dealers. In large consuming areas, such as the metropolitan districts of New York or Philadelphia, one operator may sell to several

Jan 1, 1936

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.'s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By J. F. Butler

The degree and type of carbide dispersion resulting from changes in the cooling rate from austenite determine the amount of carbon remaining in solution after slow cooling- from a subsequent subcritical annealing treatment. A difjusion model has been proposecl to explain the effect of carbide dispersion on the amount of carbon retained in solution and the amount of carbon in solution has been related to the degree of carbon strain aging. COTTRELL and Leak' have shown that the rate of strain aging in low-carbon steels is dependent upon the amount of carbon and nitrogen in solution. Carbon can be effectively removed from solution as Fe , C by quench aging at temperatures of 200" C or lower; however, the relatively higher solubility of nitrogen at these temperatures prevents sufficient removal of nitrogen as iron nitrides. For this reason, nitrogen in solution has been considered the major cause of strain aging in rimming grades of commercial low-carbon steels. Nitrogen can be effectively removed from solution and nonaging steel produced through the addition of aluminum to form the stable nitride, AlN; however, the aluminum also causes deoxidation resulting in a killed steel. III an attempt to produce a rimmed steel which was also nonaging, Morgan and Shyne 2 investigated tile strain-aging properties of low-carban steels containing boron and found that strain aging was suplx-essed in steels containing as little as 0.007 pet B. The original purpose of this investigation was to determine the mechanism of strain-aging suppression by boron. Early in the study, the function of boron was discovered to be much like that of aluminum in that the formation of a nitride, BN, removed the nitrogen from solution.' However, during the course of the investigation, an effect of heat treatment upon the strain-aging properties and the amount of carbon in solution was found which could be related to the microstructure of the steel. The purpose of this paper is to examine these relationships among heat treatment, microstructure, carbon in solution, and strain aging in steels where nondetectable amounts of nitrogen are present in solution. EXPERIMENTAL PROCEDURE The investigation was carried out using 0.030 in. by 12. in wire specimens which had been cold swaged and drawn to the final diameter. Table I lists the compositions of the low-carbon steels used. Those with 'V' designations were vacuum melted and cast; the alloys designated 'AISI' were prepared from high-purity iron obtained from the American

Jan 1, 1962

By L. C. Glenn

IN the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. OIL IN TENNESSEE A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about. 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were producers. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that

Jan 1, 1920

By E. J. Schmitz

Coming from San Antonio, Texas, and following the Galveston, Harrisburg and San Antonio Railroad westwards, one enters soon the Cretaceous formation, which forms a belt of several hundred miles, extending westwards to the boundary of Arizona and across the Rio Grande into the State of Coahuila, Mexico. The members of this formation are very numerous and in petrographical character very diverse—from a whitish or bluish, slaty, impure limestone to a hard, beautiful blue-and-red striped, and a compact heavy-bedded,

Jan 1, 1885

By George B. Langford

THE McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dikes of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compressive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed-an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitit,e dikes.

Jan 1, 1938

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the' second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson' argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

INTRODUCTION The after-tax rate of return that properly discounts future cash flows is usually referred to as the "discounted cash flow-rate of return" (DCF-ROR). The method is also referred to as the internal rate of return, true rate of return, and investor's rate of return in some literature. According to Stermole (1974, p. 188) industry polls indicate that the DCF- ROR method is the number one economic evaluation decision method used by more than 90% of the industrial companies that use for- mal economic evaluation procedures. Other economic evaluation methods that have been used in the past, such as payback period, accounting ROR, etc., have largely given way to DCF-ROR analysis because they fail to account properly for the time value of money. DCF-ROR is generally defined as that rate of return that makes the present worth of future generated cash flow over the life of the project (including after tax salvage value) equal to the present worth of all after-tax investments. The "present worthing" of future cash flow involves discounting future cash flow to a present value according to the mathematics of compound interest at some interest rate. The determination of the interest rate that equates the present worth of future after-tax earnings with the present worth of all after-tax investments necessary to create such earnings is properly called the discounted cash flow rate of return analysis. Although present worth calculations are usually used for determining the DCF-ROR, the same results can be obtained by comparing income and costs of any equivalent point in time, i.e., future worth, etc.

Jan 1, 1980

By Shosei Serata

Conventional roof bolting may be giving ground to a new technique that utilizes only the ground itself to stabilize mine openings. This newly developed stress control technique (SCT) has initially been used in sedimentary ore bodies that are both overlain and underlain by weak strata. The technique is also suited to the design of production panels and main entry systems, and is readily adaptable to room and pillar as well as total- extraction mining, including both shortwall and longwall coal mining. In applications where the technique has been used, the requirements for roof bolting and floor renewal were virtually eliminated. The SCT comprises three basic methods and covers a wide range of problems associated with failing roofs and heaving floors in underground mines (see Table 1).

Jan 5, 1976

By J. P. Van Kleunen

9.3-1. Introduction. The demands of industry for handling materials at higher rates and at reduced costs have had a very significant effect on belt conveyor technology. Although the general appearance of the belt conveyor today is essentially the same as it has been for the past several decades, the similarity ends there. Each component comprising the conveyor system has been continuously improved through design and materials technology to enable present conveyor systems to operate at ever-increasing rates and reliability. For example, twenty years ago the strongest commercially available, fabric-reinforced conveyor belting had a tension rating of 50 lb per ply-in. Currently, fabric-reinforced belts are available with ratings of 350 lb per ply-in. and steel cable reinforced belting is available with tension ratings of 3000 lb per in. of belt width (3). These technological advances have therefore enabled the belt conveyor to not only attain acceptance as a preferred method for in-plant movement of bulk materials, but also to be used for long distance transportation of bulk materials, particularly in areas of adverse terrain. The information contained in this chapter is intended to assist the reader to make basic decisions regarding the use and application of a conveyor system. The design of an overland conveyor transportation system or an in-plant process conveyor is accordingly beyond the scope of this article. Many comprehensive technical works covering the design of a belt conveyor are currently available from the manufacturers of materials handling equipment (6, 7, 9, 11). The design handbook published by the Conveyor Equipment Manufacturers Association is particularly recommended (2). 9.3-2. Conveyor Capacities. One of the most important factors in determining the proper size of a conveyor system is the rate at which material must be handled. Although tables and charts are available to the conveyor designer to assist him in his selection of conveyor components, only the

Jan 1, 1968

By W. B. Devereux

The special mriditions under which gold occurs in the Potsdam formation of the Black Hills prew~lt features worthy of a more systematic pesentation than they have heretofore received. The notes

Jan 1, 1882

By Anthony Anable, J. V. N. Dorr

When separate treatment of sand and slime by cyanidation was the rule rather than the exception, as now, and when gravity concentration, rather than flotation, was the accepted method of dressing copper, lead, zinc and other base ores, classification was a separate step in ore treatment. Today, however, the picture is much different. The trend toward all-slime treatment in cyanidation and flotation has made fine closed-circuit grinding essential, and the mechanical classifier is of equal importance with the mill in the preparation of an ore for its treatment. Actually, a mill and classifier are a unit, a variation in either affecting the desired results. In developing this thesis—the mutual interdependence of the rotary mill and the classifier in modern fine-grinding practice—it would be well to consider first the different types of classifiers and mills in use today, their scope and limitations and the factors governing their selection. From such a basis as this a logical approach may be made to modern closed-circuit fine grinding, the evolution of multiple-stage grinding practice, the relation of the classifier to the mill and, finally, the trend to higher and higher circulating sand loads in the mill-classifier circuit. Such data as are germane to the subject will be given to support the thesis advanced. Mechanical Classifiers Theory.—Stokes' law, applicable to the uniform slow motion of a rigid sphere in a viscous fluid of infinite extent, states that the velocity of a particle settling under the influence of gravity is a function of the square of its radius: _ 2 g(ds - de)?2 v =9 S Where V = velocity of particle in cm. per see. g8, acceleration due to gravity d8, density of particle de, density of fluid ? = radius of particle S = viscosity of fluid

Jan 1, 1935

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.1,2 Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1952

By R. S. Shoemaker, F. W. McQuiston

RECOVERY METHODS AS RELATED TO PROPERTIES OF SILVER ORES The earliest metallurgical process for treating silver ores was amalgamation with mercury which was in use in the early 1500's. Closely following was the development of the Patio process for treating ores at Pachuca, Mexico. Silver often occurs as the native metal and in deposits associated with other metals such as gold, copper, lead and zinc. Principal silver minerals include compounds of sulfur, antimony, arsenic, and copper. Silver chloride, and argentiferous galena are also prime sources. Native silver and the chloride characterize the oxide zone of most deposits. Native silver can be concentrated, amalgamated, or cyanided. Silver chloride rapidly dissolves in cyanide without oxygen. Oxidized silver ores containing the higher oxides of manganese are generally refractory to metallurgical treatment. A refractory compound of manganese and silver is formed, probably a manganite , which is insoluble in cyanide solutions. Argentite is the predominant silver mineral. Other important economic minerals are native silver, argentiferous galena, cerargyrite, pyrargyrite and tetrahedrite. Argentite dissolves slowly, the reaction being reversible requires an excess of cyanide. Argentite with disseminated fine grained gold occurring in quartz veins with minor amounts of chalcopyrite and galena may be cyanided directly after grinding, with high silver and gold recoveries. The flowsheet adapted to this type of ore is the Minas de San Luis, Tayoltita cyanide plant, which treats a high grade argentite silver ore containing gold. It is a standard cyanidation circuit but employs long periods of agitation contact for the high silver sulfide content ore. Lead-zinc base metal semi-oxidized- complex ores in pipes and chimneys are replacement deposits in limestone at El Mochito Mine, Honduras. Mineralization comprises galena, cerussite, anglesite, sphalerite, calamine, and smithsonite. The silver content of about 16 ounces occurs as native silver globs, wire and the mineral argentite. After flotation of lead and zinc concentrates, the tailings are cyanided for gold and silver recovery. The great Huelva pyritic copper deposits of Spain carry a little gold and silver. At Cerro Colorado, these metals were concentrated above the chalcocite zone into the so-labeled Mgossanu. This material with a content of 0.08-0.09 oz Au and 1.50 oz Ag per ton is amenable to cyanidation. See Cerro Colorado flowsheet. In southern Hidalgo, about 60 miles north of Mexico City, are the great silver--gold veins of one of the foremost silver mining districts of the world. Real del Monte, Pachuca. The mineralized area consists of flow rocks and intrusives. The oxidized ores carry pyrites with oxides of iron and manganese and other minerals, silver and gold. The first zone contains

Jan 1, 1975

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954