Search Documents

By J. E. Pavlick, W. W. Mullins, H. W. Paxton

The growth of nitrogen-austenite during nitriding of large-gvained ferrite between 650" and 800°C has been studied as a functimz oJ time and nitrogen potential of the atmosphere for a variety of alloying elements dissolved in the ferrite. Whereas no preferential grain boundary penetration by aistenite takes place in zone-refined iron, the addition of aboit I zot pct oj' V, Ti, Cr. Si, or A1 produces significant protrusion of austenite down former 0-0 boundaries. This group of elernents also produces ragged y-0 interfaces in the a grains which advance more slozuly than those in zone-refined iron. 1 zut pct of Ni, Co, Mn, or Mo dissolved in ferrite leads to essentially smooth 7-a interfaces, which advance at rates very sinzilar to those in zone-refined iron. The reasons for this effect are not clear. Two possible limiting hypotheses, not necessarily exclusive, are discussed. One involves p.referentia1 grain bozindary diffusion of nitrogen. the other the production of a zone of ferrite, stpersatcirated with respect to nitrogen, from which austenite precipitates helerogeneozisly on the a-a gyain boundaries. In many phase transformations which occur by nu-cleation and diffusion-controlled growth, information on the parameters which control the rates of nuclea-tion and of growth is frequently not quantititative. The present work describes a continuation of efforts to obtain quantitative data on growth rates in systems where thermodynamic and kinetic factors are known independently, and thus where comparison with models of the growth process is possible. The work has been conducted on iron-base systems for two reasons. Firstly, there are several interesting transformations in this system, many of which are of practical importance. Secondly, the information on phase diagrams, activities, and diffusion coefficients is more complete in this system than in any other. These data are still inadequate to check all the effects of alloying elements, but at worst it is possible to make estimates and thus examine order-of-magni-tude agreement with proposed models. It will be necessary to do this in the present work. The problem studied was the growth of nitrogen-austenite in from the surface of large-grained columnar crystals of alloyed ferrite exposed to an NHs/Hz atmosphere. Earlier work by Grozier et al.' had suggested that growth of austenite may occur preferentially along grain boundaries of alloyed ferrite, whereas zone-refined (ZR) iron shows no such effect, Fig. 1. Growth of nitrogen-austenite into single crystals of zone-refined ferrite is planar provided sufficient nu-cleation sites for austenite are present, and is controlled by volume diffusion of nitrogen through the

Jan 1, 1967

By Hans W. Brodbeck

The main problem in tunneling without the use of explosives lies in the development of tools capable of continuous mechanical destruction of rock, resulting in a fragmentation which lends itself to a smooth, uninterrupted transportation of the broken rock away from the tunnel face. While all moles of U.S. design mainly achieve this by crushing the rock by means of "disk cutters" or "roller bits," a boring system based on the principle of cutting the rock came into being in Europe, whereby the rock is worked in a manner very similar to the milling of metals. For tunneling purposes, this principle was first developed by the late Austrian engineer Wohlmeyer. Between late 1962 and the spring of 1965, the first experimental machine was tested in a German coal mine, working in coal and shale over a distance of some 3000 ft, divided over two runs separated by a period of time to allow for equipment modifications. In 1964, a collaboration was started between Wohlmeyer and the Habegger engineering firm of Thun in Switzerland. The normal Habegger range of equipment consists of aerial ropeways, ski lifts, and certain tool machines, to which in later years have been added monorail passenger-transport systems. One of these was installed as the main mode of transport at the 1967 World Fair in Montreal. After taking over the Wohlmeyer patents, Habegger further developed the original cutting principle, aiming at more robust machines in order to be able to tackle harder rock. A first machine was built and tested at a site near Thun in sandstone averaging 17,000 psi compressive strength and limestone of 25,000 psi. In May 1966 this machine was delivered to Japan for the boring of a pilot tunnel for the Honshu-Hokkaido railway connection under the sea. A second machine, incorporating many improvements based on experience gained with this first mole, was built during 1966 and tested in the same limestone as mentioned previously (25,000 psi), before being installed to bore the head race tunnel of the Julia hydroelectric power scheme near St. Moritz, Switzerland, in the early summer of 1967 (Fig. 1 ) .

Jan 1, 1970

By E. J. Wasp, T. C. Aude, F. B. Raymer

Abstract-The following paper deals with technical aspects of terminal facilities for western coal pipelines. The information is taken from the Ohio and Black Mesa pipelines and the proposed one in Wyoming. This paper first discusses the feed terminal, the product that it must produce, and the reasons for coal cleaning. Then, in the delivery terminal section, the various methods of dewatering the coal and some recent innovative ideas on bunkering the dewatered product and storing the dewatered coal in large outdoor piles are discussed.

Jan 2, 1978

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By J. R. Long, R. S. Dean, D. C. Root, E. T. Hayes

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By H. Schwartzbart, J. R. Low

Annealed, .Poly crystalline, low carbon steel exhibits a phenomenon known as the "yield point." If such a steel is loaded in tension, the load increases steadily with elastic strain, drops suddenly, fluctuates about some constant load value for a time and then rises with further strain. The load at which the sudden drop occurs is called the "upper yield point"; the load at which deformation proceeds at constant load is known as the "lower yield point"; the amount of elongation at constant load is termed the "yield point elongation." Deformation which occurs during the yield point elongation is heterogeneous in nature, deformed metal existing next to undeformed metal. The drop in load from the upper yield point is concurrent with the formation of a band of deformed metal which usually appears at a stress concentration such as a fillet and at an angle of approximately 45" with the direction of pull. As deformation proceeds during the yield point elongation, the deformed region grows until the entire specimen has been strained an amount equal to the strain in the first band. A phenomenon very often associated with the yield point is that of strain aging. Aging in steels may be of two types: quench aging, or precipitation hardening, and strain-aging. Strain aging differs from precipitation hardening in that if the metal is merely strained instead of given a solution anneal and quenched, it then undergoes changes in properties similar to those observed in quench aging. The yield point effect and strain aging are most markedly exhibited by low carbon steel, but have been observed in other alloys. Numerous explanations for the mechanisms of both phenomena have been advanced, but the evidence for the acceptance of any of the hypotheses is incomplete. One of the explanations of the yield point phenomenon frequently proposed is that there exists a honeycomb of grain boundary material that supports the load above the yield strength of the ferrite and that when this network ruptures, the ferrite flows with no increase in load. This notion was first advanced by Dalbyl in 1913 and has been since put forward in more concrete form by many investigators. The testing of this hypothesis was, in part, the object of the present investigation. Similarly, the mechanism by which strain aging occurs remains to be explained. Presumably, it is a precipitation hardening phenomenon similar to quench aging, the precipitation being initiated by strain. However, it is not known whether the process is a solution and precipitation effect or a change in solubility due to strain. One obvious method of determining whether or not the yield point is a grain boundary phenomenon is to determine if single crystals exhibit a yield point. Low and Gensamer2 have shown that carbon and nitrogen are responsible for the yield point and aging in steel and that these effects can be eliminated by the removal of these elements through wet hydrogen purification. Single crystals that have been grown in wet hydrogen treated material must then be recarburized or re-nitrided in order to evaluate the effect of grain boundaries. In the present investigation, single crystals of iron which had been annealed in wet hydrogen to remove the carbon and nitrogen were cut into two specimens having the same orientation with respect to the tension axis. Of these, one specimen was pulled in tension in the wet hydrogen treated state and the other was carburized or nitrided and tested similarly. All the crystals were examined for a yield-point and strain aging. The grain boundary hypothesis for the explanation of the yield point in steel has been tested only indirectly previously. Arrowsmith,3 Andrew and Lee,4 Edwards and Pfeil,5 Fell,6 Ludwik and Scheu,7 Winlock and Leiter8 and others found a decrease in proportional limit and yield point effect with an in-

Jan 1, 1950

By W. A. Wood, W. H. Reimann, K. R. Sargant

A study is made of the microstructural changes produced in armco and pure iron subjected to alternating torsion at amplitudes above and below the knee of the S/N curve. The aim was to identify the basic mechanisms of fatigue and to find why they should give rise to a sharp S/N knee in contrast to the type of S/N curve shown by fcc metals. It is found that the basic structural change above the knee in the iron is a pronounced cell formation in the grains, which determines irregular micro-cracks, and below the knee a dispersion of fine slip that determines a dispersed pore formation in the grains. Comparison of these changes with those in fcc metals similarly tested shows that they do not include an intermediate structural change, a concentrating of slip in narrow bands with associated slip-band cracking, that characterizes the fcc metals and accounts for their different type of S/N curve. RECENT conferences on basic mechanisms of fatigue emphasize that fatigue damage takes many forms: for example, cracking in slip bands (Thompson1), at grain boundaries and inclusions (Hempel'), at precipitation zones in alloys (Han-stock, Forsythe), or at surface notch-peak effects, both hypothetical (Mott, cottrel16) and observed (Wood). Evidently it is not easy to see in this diversity a basic mechanism. At the same time the contributions suggest that some reconciliation may be possible if distinctions are drawn between three phases of the fatigue process: initiation of damage at nuclei, distribution of these nuclei, and the final macroscopic crack system. In initiation, the relevant features appear to be that nuclei may appear early, at least by 1/100th to 1/1000th of the life of a test specimen; that they may do so at many independent centers, appearing according to some observationsa as pores or voids; and that they are not necessarily self-propagating, damage spreading rather by their multiplication. In distribution, the relevant feature appears to be that they form preferentially in zones where the microstructure becomes abnormally strained (as defined more closely below). Now in these two phases the basic fatigue process should be systematic. But, at the same time, the "abnormal strains" in particular set the stage for considerable diversity in the final phase of macroscopic cracking, for where zones of abnormal strain develop will depend on what kind of fatigue deformation is applied and what kind of prior processing the test material has had. On this view it seems desirable to know what in

Jan 1, 1964

Idaho Bureau of Mines and Geology, University of Idaho, Moscow, Ida. John W. Finch, Director. A list of publications will be sent upon application. A series of Bulletins and Pamphlets have been issued by the Bureau to date since 1920 Of the Bulletins, six are out of print, and a charge is made for eight. Each of the Bulletins, in the main, treats of the geology and resources of a particular district in Idaho, as follows (only available Bulletins listed): Bulletin 1, South central Idaho (1920), 15 cents, 7, North central Idaho (1924), 50 cents, 8, Bonneville, Bingham and Caribou counties (1924), 50 cents, 9, Boise Basin (1924), 50 cents; 10, Boundary County (1926), 50 cents; 11, Region about Silver City (1926), 50 cents; 12, Clark Fork district (1930), 50 cents, 14, Eastern Cassia County (1931), 50 cents, Press Bulletin 15, Teton County (1927), Bulletin 16, Melon Valley near Buhl (1927); 17, Concerning land slips near Whitebird, Idaho (1928) The 37 Pamphlets are issued free of cost, and each treats, also, in the main of the geology and resources of a particular district in Idaho Nos 1, 2, 3, 4, 5, 7, 8, 10, 17, 18, 20, 22, 25, 26, 30 and 35 are out of print Of those available, attention may be called to Pamphlet 6, Reported platinum occurrences near Coeur d' Alene (1925), 11, Bruneau River Basin, 12, Power and Oneida

Jan 1, 1933

In cooperation with the United States Bureau of Mines and the Idaho Bureau of Mines and Geology, the University of Idaho offers in the School of Mines a number of fellowships. These fellowships are open to college graduates who have had good training in mining, metallurgy, or chemistry, and who are qualified to undertake research work. The income of each fellowship is $720 a year for the 12 mo. beginning July 1, 1919. Fellows will register as students in the University of Idaho and become candidates for the degree of Master of Science in Mining or Metallurgy (unless this or an equivalent degree has been earned). Their class work-will he directed by the heads of the departments of instruction, but the greater portion of their time will be spent in research work under the direction of the Bureau of Mines staff resident at the University. The purpose f this work is to undertake the solution of definite problems confronting the mining and metallurgical industries of the State of Idaho. For 1919-20 the following subjects are being considered: 1. Flotation-with especial reference to differential separation of various minerals. 2. Availability of western wood oils for flotation purposes. 3. Treatment of the complex gold-silver ores of southern Idaho. 4. Ore-dressing problems. 5. Mining problems. Applications, with certified copy of collegiate record, statement of professional experience, and names and address of three references, should be addressed to The Dean. School of Mines. Moscow Idaho_

Jan 6, 1919

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

By C. G. Black

The purpose of this paper is to present data obtained from an investigation conducted on the grindability of coal by the American Society for Testing Materials Tentative Standard ball-mill method. This investigation has been conducted over a period of a year, during which time several hundred tests were run on a wide selection of different coals coming from Pennsylvania, Ohio, West Virginia and Kentucky. The data herewith presented tend to show that the tentative standard ball-mill method might give results that are misleading and that a volume measure might be more indicative of the true grindability of materials of varying specific gravity. A means whereby the time element might be reduced has been studied and other phases of this work such as preparation of samples, mechanical screening, reporting results and duplicating tests have been investigated. It is hoped that all criticism offered in this paper will be taken as constructive, with the purpose ill mind of perfecting the method now tentative to show the true conditions 2nd of making optional the manner in which certain parts of the test might be conducted to meet diversified laboratory conditions. Weight and Volume The results of grindability on extraneous material from the coal scam obtained with the present tentative standard ball mill method indicate easier grinding of these materials as compared to most coals. Varying amounts of these impurities in the coal therefore may cause a raising of the grindability index and may lead to the erroneous conclusion that coals containing large amounts of these foreign materials are easier to grind. For a true comparison of grindability, it would seem necessary to grind to the same particle weight. If material were sized in a commercial mill by means of an air current set at a velocity to remove 1.60 sp. gr. float coal ground to 80 per cent minus 200 mesh, any 1.60 sink particles would be left behind, and in order to remove this 1.60 sink material by the same current it would be necessary to grind finer and produce a

Jan 1, 1936

ROESLER MAX-Geology of the Iron-Ore Deposits of the Firmeza District, Oriente Province, Cuba. Discussed by William Kelly, J. T. Singewald, Jr., B. L. Miller, J. D. Irving, L. C. Graton, C. P. Berkey 439 SINGEWALD, J. T., JR., AND MILLER, B. L.-The Manganese Ores of the Lafayette District, Minas Geraes, Brazil. Discussed by L. C. Graton, J. T. Singewald, Jr., F. Lynwood Garrison HARDER, E. C.-Manganese Ores of Russia, India, Brazil, and Chile. Discussed by J. T. Singewald, Jr., E. C. Harder 454 SCHRADER, FRANK C.-Geology and Ore Deposits of Mohave County, Arizona. Discussed by J. C. Anderson McDOWELL, J. SPOTTS-A Study of the Silica Refractories. Discussed by J. W. Richards, H. D. Hibbard, W. F. Rochow, J. B. Umpleby-: 460 PHALEN, W. C.-The Conservation of Phosphate Rock in the United States. Discussed by E. G. Spilsbury 462 NORTON, S., AND LEFEVRE, S.-The Magnetic Concentration of Low-Grade Iron Ores. Discussed by G. C. Foote, J. L. W. Birkinbine, F. L. Nason 462

Jan 4, 1917

By Hiro Minagawa

Japan's contact with the mining industry of British Columbia began as far back as 1952 with the first shipment of iron ore from the Texada mine. Five years later, the Big Three steel mills of Japan-that is, Nihon Kokan Kaisha, together with Yawata and Fuji Steel Mills-dispatched a coal survey mission to inspect coal mines in British Columbia. This resulted in 100,000 tons of coking coal being initially imported by Japan from western Canada in 1959. Also in 1959, Yawata, Fuji, NKK, Kawasaki and Sumitomo sent an iron ore survey group to Alaska and Canada. During the preceding year, Nippon Mining Company and Sumitomo Metal Mining Company initiated a project whereby they would assist in the development of Cowichan Copper on Vancouver Island. As a net result of this activity Japanese mining groups, who had heretofore concentrated on Southeast Asia and South America, finally turned their eyes toward Canada. It was in the fall of 1960 that the government of Japan, in order to keep pace with Japan's rapid economic development, announced a long-range economic plan whereby her gross national income would be doubled by 1970. This had the effect of further propelling Japan's desire to develop sources of raw material supplies abroad. With the development of Craigmont Mines and the signing of a long-term contract to export copper concentrates to Japan, and with the Sumitomo group's extending financial assistance to develop Bethlehem Copper, Canada itself began to realize that Japan was indeed a very important market for British Columbia. A number of surveys to develop mines in British Columbia was begun with an eye on Japan as the major market, and the activity has continued to this day.

Jan 12, 1963

By R. G. Ward, D. R. Gaskell

Using the maximum bubble pressure technique, the densities of iron silicates at 1410°C have been measured blowing helium, nitrogen, and argon. By ensuring equilibrium between the melt and the blowing gas with respect to oxygen potential and by minimizing tempcrature cycling of the furnace, iron precipitation in the melt has been prevented. Thus the previously reported effect of blowing-gas composition on the densities of the melts has been eliminated. Consideration of the oxygen densities of the melts gives an indication of the structural changes accompanying composition change. The density-composition relationship of iron oxide-silica melts in contact with solid iron has been the subject of several investigations1-7 and considerable disparities exist among the various results obtained. Of these investigations, all except one5 have employed the maximum bubble pressure method. In the most recently reported of these investigations1 the density-composition relationship obtained blowing nitrogen differed from that obtained blowing argon. The measured densities obtained under nitrogen were greater than those obtained under argon, the difference being a maximum at the pure liquid iron oxide composition and decreasing with increasing silica content. This observation rationalized the disparities existing among the results of the earlier investigations, showing that two lines, one for nitrogen and the other for argon, could be drawn to fit all the earlier results. No explanation for this phenomenon could be offered. Chemical analysis of rapidly quenched samples of melt for dissolved nitrogen, and direct weighing measurements, excluded solution of nitrogen in the melt from being the cause of the increase in density. The range of blowing gases was extended by Ward and Hendersons who measured the density of liquid iron oxide bubbling helium, nitrogen, neon, argon, and krypton. The measured density was found to decrease smoothly with increasing atomic number of the bubbling gas. The work reported here is a continuation of the program initiated by Ward and Sachdev7 to study the densities in multicomponent melts in which the iron oxide-silica system is the solvent. As such it is necessary to explain or eliminate the anomalous densities of iron silicates under different atmospheres, and the present rede termination was carried out towards this end. EXPERIMENTAL The maximum bubble pressure method of density determination was again employed and the experimen- tal apparatus used was essentially the same as that used by Ward and Sachdev.7 A molybdenum-wound resistance furnace heated an ingot iron crucible of internal diameter 1 in. containing a 2-in. depth of melt. The bubbling gas was blown through a 1/4 -in.-diam mild steel tube onto the end of which was welded a 2-in. extension of 1/4 -in.-diam ingot iron rod, drilled out to 5/32 in., and chamfered to an angle of 45 deg. The blowing tube was introduced to the furnace through a sliding seal and its position was controlled by a vertically mounted micrometer screw which allowed the depth of immersion to be determined with an accuracy of ± 0.01 cm. A Pt/Pt-10 pct Rh thermocouple was located below the crucible and temperature control was effected initially by means of an on-off controller and later by a saturable core reactor. The bubble pressure was determined by measurement of a dibutyl phthalate manometer using a cathetometer. PREPARATION OF MATERIALS Iron oxide was produced by melting ferric oxide in an inductively heated iron crucible in air. The liquid was quenched by pouring onto an iron plate. Silica was prepared by dehydrating silicic acid at 650°C for 12 hr. RESULTS Before any measurements of the density of a melt were made, the density of distilled water at room temperature was measured bubbling helium and argon. Both gases gave the density as 1.00 ± 0.01 g per cu cm which showed that the density of the manometric fluid (dibutyl phthalate) was not affected by contact with the blowing gas. With the furnace controlled by an on-off temperature controller an attempt was made to measure the density of pure liquid iron oxide by bubbling argon. The furnace atmosphere gas and bubbling gas were dried over magnesium perchlorate and deoxidized over copper turnings at 600°C. It was found that the pressure required to blow a bubble at a given depth increased slowly with time, and thus it was impossible to obtain a unique value for the density of the melt. Inspection of the blowing tube after removal from the furnace showed that rings of dendritic iron had precipitated from the melt onto the immersed part of the tube. This is shown in Fig. l(a) where the various "steps" correspond to different depths of immersion. The precipitation of iron was considered to be due to one or both of two possible causes: i) The composition of the liquid iron oxide is that of the liquidus at the temperature under consideration and can be expressed by the equilibrium

Jan 1, 1968

By B. G. Reisdorf

This paper describes the microstructural changes that occur when quenched ultrahigh-strength steels containing OA pet C and various amounts of nickel, silicon, and cobalt are tempered. The changes that occur in hardness, yield strength, and martensite diffraction-peak widths when these steels are tempered are related to the precipitation of the carbide phases. An unea$ectedly high silicon content (about 30 pct) was found in the E -carbide phase in a steel containing only 1.5 pct Si. TEMPERED martensitic steels have such wide-spread utility that they have been the subject of numerous investigations, and a sizable amount of literature has developed on this subject.M This investigation, which is a part of a larger program to correlate microstructure with mechanical properties at a variety of strength levels, is limited to the microstructural changes that occur when a quenched 0.40 pct carbon steel (USS Airsteel X-200 steel) is tempered, and to the effects of the alloying elements—nickel, cobalt, and silicon—on these microstructures. Used in this investigation were electron microscopy, electron-diffraction identification of the carbide phases, electron-probe micro-analysis of the carbides, X-ray determinations of retained austenite, and measurements of martensite X-ray diffract ion-peak widths. MATERIALS AND METHODS The chemical analyses of the eight heats examined eats No. 30 through 37) are shown in Table L Heat No. 30 has the chemical com~osition of Airsteel X-200, and the remaining seven heats contain various amounts of nickel, chromium, cobalt, and silicon. The heats were air-melted in an induction furnace and cast into 8 by 8 in. ingots that were subsequently heated to 2300 and rolled to 1-in.-thick plate. Oversize 0.505-in.-diam tensile specimens were rough-machined from the plates and austenitized in air at 1700° F for half an hour and oil-quenched. The specimens were then tempered in air at temperatures of 400° to 1000 for tempering times of 1, 4, and 16 hr, and finish-machined to 0.505-in.-diam tensile specimens. Electron micrographs were prepared from Formvar replicas of the midthickness of tensile-specimen shanks that had been electrolytically polished and etched in nital. Electron-diffraction patterns were obtained from carbon-extraction replicas. The replicas were prepared by etching the sample surface in the same manner as for microscopy, evaporating carbon on the etched surface, and re-etching the sample to free the carbon film and the precipitate particles. Electron-probe microanalysis was performed on some of the extraction replicas. To obtain adequate fluorescent X-ray intensities, several thicknesses of replica were exposed to the electron beam so that the results represent an average composition of the extracted particles rather than an analysis of single precipitate particles. The retained austenite contents of the specimens were determined by an empirical X-ray diffraction

Jan 1, 1963

By E. A. Swedenborg, J. S. Ross

Oil-field waters enter into many underground problems with which the petroleum engineer has to deal. Whether the problem is one of infiltration or natural encroachment, it is always desirable to determine the source of the water before commencing repair or remedial work. The usual mechanical tests for determining the source of extraneous water in wells are slow and expensive. An excellent means for the identification of oil-field waters may be afforded by their chemical characteristics when the chemical character of waters from the various sands has been established by careful sampling and analysis cautiously interpreted. In the Salt Creck field, Wyoming, a fairly high degree of efficiency has been attained in the control of field operations by utilizing the information afforded by the analysis. All of the operating companies appreciate this means of identifying waters, with the result that water-sampling has become general practice. Most of the chemical work dealing with Salt Creek waters has been done since the laboratories of the Midwest Refining Co. and the U. S. Geological Survey, were established in the field; the former in 1922, the latter in 1924. A spirit of cooperation has existed between the company and the government personnel by which many of the data for this paper were made available. Sands of the Salt Creek Field The principal sand horizons in the Salt Creek field are the Shannon, First, Second, and Third Wall Creeks, Dakota, Lakota, Sundance and Tensleep. Of these the important oil producers are the First Wall Creek, Second Wall Creek, Lakota and the Sundance. The Third Wall Creek is lenticular and is productive in only a few wells in the southern end of the field. There are also a number of shale wells, but they do not produce water in any appreciable amount. The stratigraphic position of these sands and their relative thicknesses are shown on the condensed composite section of Salt Creek

Jan 1, 1929

Jan 1, 1881

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939