Search Documents

By A. S. Eve

IN the spring of 1930, the question was raised as to the possibility of estimating the depth to which the pyrrhotite-nickel deposit at the Falconbridge mine extended in the earth. This body is 7500 ft. long, it dips at 80° to the north, and it is fairly straight with slight sinuosities. Dr. F. W. Lee suggested that it might be possible to solve the problem by measuring the vertical magnetic intensity, with a good magnetometer, both near the surface of the earth and also at a level a 'few feet higher in the air. The writer regarded this suggestion with some scepticism, but it was decided to put the scheme to a prac¬ tical test. In July, 1930, Dr. Lee, Dr. Keys and I ' the writer, with Mr. Joyce and Mr. Belloc as assist¬ ants, made a firm, light wooden platform (Fig. 1) E measuring 4 by 4 ft. on the top, which was 10 ft. above ground. This platform could be moved easily a few yards by four men, and carried across I country in a wagon or by motor truck. Some iron nails were used in its construction, but we were not able to detect their influence on the - Askania magnetometer. Nevertheless, in future work, the use of iron should be completely avoided. Readings were taken along a traverse at right L angles to the orebody, at several stations, both on FIG. 1.-VERTICAL the ground and on the platform. The excess read- ASKANIA MAGNETOM¬ ETER ings, over the dike, as compared with those about 10 ETER ON A FT. HIGH. PLATFORM 800 ft. away, are shown in Table 1. The largest reading, 6.8, is open to suspicion and should be rejected. The depth of the top of the orebody is known by electrical survey, and by actual drilling, to be about 112 to 123 ft., and the covering is sandy glacial drift. Similar readings were taken over a long straight magnetic diabase dike. These also are shown in Table 1. The magnetic vertical intensity is consistently less at the higher level, which is l0 ft. above the lower level.

Jan 1, 1931

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1915 to Jan. 10, 1916. ANDERSON, FRANK BASIL, Min. Engr., Sampler, Copper Queen Cons. Min. Co., Bisbee, Ariz. BAILEY, LEWIS NEWTON, Min. -Engr 4227 St. James Place, Sail Diego, Cal. BELL, JAMES E., Min. Engr., Care Chile Exploration Co., Chuquicamata, Chile, South America. BONILLAS, YGNACIO SAFFORD, Min. Geol., Copper Queen Cons. Min. Co., Bisbee, Ariz. BRADLEY, GEORGE OLIVER, Mech. Engr Hobart Bldg., San Francisco, Cal. CLARK, GEORGE L., Min. Engr Vipond Mine, Schumacher, Ont., Canada. CONKLING, RICHARD A., Geol., Roxana Petroleum Co. of Oklahoma, Tulsa, Okla. GOHRING, W. B.. Geol., Supt. of Mines, Calumet and Arizona Min. Co., Warren, Ariz.

Jan 2, 1916

INTRODUCTION Within the past few years Clark (1972), King (1970), and King, et al. (1973), have summarized porphyry molybdenum occurrences. Clark (1972) includes as porphyry or stockwork deposits some occurrences more recent exploration has shown to be of other genetic types. King (1970) and King, et al. ( 1973) provide broad general descriptions that unfortunately are restricted to the US. Nor does the King, et al. (1973) description have benefit of the Wallace (1974), Hall, et al. (1974), or Giles (1975) data on alteration, fluid inclusions, or isotope chemistry. The synthesis presented here up- dates these older summaries, eliminating all but the well established porphyry molybdenum deposits as well as enumerating the unifying characteristics displayed by these deposits within the Cordillera of North America. This type of deposit occurs in the South American Andes as well, but Andean deposits are not well documented so only North American Cordilleran deposits are considered. Stockwork, porphyry, and Climax type molybdenum deposits are synonymous geo- logical labels for the large molybdenite de- posits found in parts of the western Cordillera of North America (Khruschov, 1959). These labels describe and define the type of deposit discussed herein. The term porphyry is preferred for this chapter because it describes the common characteristics; it separates the molybdenum deposits from the porphyry copper deposits, which have many similarities but also important differences. This usage also eliminates blanket application of the word stockwork to breccia pipe deposits such as Boss Mountain in British Columbia. J. R. Woodcock has contributed much to this chapter; his influence, original data, and thoughtful comments qualify him as co-author. Porphyry molybdenum deposits are characterized by fine-grained molybdenite occurring alone or with quartz and/or pyrite in fractures and open spaces of stockworks and breccias. The molybdenite is generally less than one millimeter across and in many cases too fine-grained to be seen with the aid of a hand lens. Occasionally some deposits con-

Jan 1, 1978

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

J. A. MATHEWS, ? Syracuse, N. Y. (written discussion§).-This paper by Prof. Hoyt, together with the papers by Messrs. Jeffries, Clayton, Rawson, and Moore, submitted at this meeting, constitute a valuable symposium on what might be called the "mechanism of failures." Prof. Hoyt has not emphasized too strongly the importance of the notched-bar test, or the notch as a feature of a structural design. There has been a good deal of misunderstanding in reference to the value of the notched-bar test, and various vibratory tests such as the Wohler, White-Souther, Stanton, and Upton-Lewis have been devised. This form of testing has received more attention abroad than it has here, and has been the subject of a great many very careful investigations. I have heard many expressions of surprise at the apparent lack of agreement between the results of vibratory tests and the results of shock tests. It is not necessary that the values obviously should agree, because obviously different properties are being tested. In reference to the presence of notches or sharp corners in the construe tion of machines or parts, would say that these more frequently lead to fatigue failures than to typical notch-bar failures clue to sudden impact. I have seen a number of airplane crankshafts that had apparently failed due to a keyway that was left with fairly sharp angles at the bottom. The material satisfactorily responded to every test, including the notched-bar test, nevertheless the shafts failed, showing a fatigue break, usually spiral and sometimes making at least one complete turn around the shaft. The lack of concordance between supposedly duplicate notched-bar tests in my experience has been most often due to lack of care in the machining of the test piece itself. Prof. Hoyt draws attention to a report of Charpy in 1909, in which two steels of almost identical physical properties show very different results in the notched-bar test. He states that the microstructure at once showed that one steel was in poorer condition than the other. More recent experience has shown other cases of this kind where not even the microstructure serves to reveal any startling differences in structure.

Jan 4, 1919

By Jasper L. Stuckey

GEOGRAPHICALLY, North Carolina consists of three divisions, the coastal plain on the east, the piedmont plateau in the center, and the Appalachian mountain region on the west. Geologically, the State may be divided into two main divisions, an eastern or coastal plain region, and a western or piedmont plateau and mountain region. The eastern region is underlain with unconsolidated sands, clays, marls, and shell limestones varying in age from Cretaceous to Recent. The western region is, in general, underlain with gneisses, schists, slates, sheared volcanics, and igneous intrusives of Pre-Cambrian age. In the mountain and upper piedmont portion of the western region are several areas of irregularly metamorphosed sediments of early Paleozoic age. Throughout the piedmont plateau and a part of the mountain portion of the western region, important areas are underlain with igneous intrusives of late Carboniferous age. Along the eastern edge of the piedmont plateau are two narrow belts, trending northeast-southwest, underlain with sediments of upper Triassic age. Although North Carolina contains a

Jan 1, 1947

By Arnold Hague

At the Buffalo meeting, October, 1888, Dr. Raymond presented a paper entitled: "Soaping Geysers" (p. 449 of the present volume), in which he called attention to the use of soap by tourists to cause eruptions of several of the well-known geysers in the Yellowstone Park. Incorporated in this paper appears a communication received from me, written from camp in the Park, in reply to some inquiries on the subject. The letter discussed somewhat briefly the means employed by visitors to the Park to hasten the eruptions from hot springs and reservoirs of hot water, which remain dormant for days, or even weeks or months, at a temperature near the boiling-point, without any display of geyser-action. As the paper has called forth considerable comment, I desire to elucidate one or two points in relation to the temperature of the springs, and to answer some inquiries about the composition of the thermal waters. In the summer of 1885, a Chinaman, employed as a laundryman for the accommodation of the tourists at the Upper Geyser Basin, accidently discovered, much to bis amazement, that soap thrown into the spring from which he was accustomed to draw his supply of water produced an eruption in every way similar to the actual workings of a geyser. Tourists with limited time at their command, who had travelled thousands of miles to look upon the wonders of the Yellowstone, soon fell into the way of coaxing the laundryman's spring into action, to partly compensate them for their sore disappointment in witnessing only the periodical eruptions of Old Faithful. Successful attempts upon this spring soon led to various endeavors to accelerate action in the dormant and more famous geysers. In a short time, so popular became the desire to stimulate geysers in this way, that the Park authorities were compelled to enforce rigidly the rule against throwing objects of any kind into the springs. In connection with a thorough investigation of the thermal waters of the Yellowstone Park and the phenomena of the geysers, I undertook a number of experiments to ascertain the action of soap upon the waters and to determine, if possible, those physical conditions of various pools and reservoirs which permitted the hastening of an

Jan 1, 1889

Report of Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I herewith present a report of some of the more important activities of the Institute for the year of 1922. The outstanding feature of the year is the optimism felt by our members despite the continued depression in the mining industry. January 1, 1921, found many of our members out of employment or drifting into other industries to tide them over the depression; but almost universally the feeling has been that this was but a temporary condition and that sooner or later the necessary production of raw materials would enable these members to return to their former activities and renew their participation in Institute affairs As the year passed conditions improved and, before it ended, many had found employment in their previous occupations. Bearing in mind that this depression has been very real, we have reason to be well satisfied with the work that the Institute has been able to do The loss of members through inability to pay dues has been large, and income has been correspondingly reduced, but it proved to be materially in excess of that anticipated early in the year, so that a substantial and unanticipated balance was carried forward toward the activities of 1923.

Jan 1, 1923

By Sidney Powers

Discussion of the paper of SIDNEY POWERS and ALFRED C. LANE, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 535 to 548. N. L. BOWEN, Washington, D. C. (communication to the Secretary*). -This detailed study and. complete demonstration of differentiation as a result of the sinking of crystals has a great general significance in petrogenesis. If this action can be demonstrated in an effusive body, even though a very thick one, how can one doubt its possibility in large intrusive bodies? The authors speak of the sinking of augite and the rising of plagioclase but I should consider that they should depend entirely on the former action to obtain their results. It is true that in my experiments, to which the authors refer, a floating of crystals was in one case obtained, viz., in the case of tridymite crystals, but it must be remembered that tridymite has an exceptionally low density. Plagioclase crystals, on the other hand, are of nearly the same density as basaltic liquid. Under magmatic conditions they might be a little heavier than the liquid or a little lighter, we do not know which, but the margin would be exceedingly small and any motion resulting, whether upward or downward, would be correspondingly small in the usual case. For this reason I should think that the sinking of pyroxene should be considered probably the sole factor in producing the observed result, for which purpose it appears to be entirely adequate. The measurements of grain have also a certain significance in this connection. In the experiments referred to a difference of grain was obtained in different parts of the charge, which was entirely independent of the rate of cooling but connected with the fact that a sinking crystal does not depend entirely upon diffusion for the collection of its material from the surrounding liquid. The crystals which sank a considerable distance were therefore exceptionally large. Now in the Cape Spencer flow the augite crystals are normally (top and bottom) somewhat smaller than the plagioclase crystals, but in the layer somewhat below the middle,

Jan 5, 1916

By D. R. George, J. R. Ross, J. D. Prater

In the United States nearly 200,000 tons of copper per year are being produced, by leaching waste rock and oxidized copper ore with dilute sulfuric acid-ferric sulfate solutions and precipitating the copper on scrap iron. The flow of solutions is in excess of 80 million gpd. A survey conducted by the U.S. Bureau of Mines in late 1965 at 14 mines in Arizona, Utah and Nevada, showed that with a few exceptions, the solutions contain from two to a maximum of 15 ppm U3O8, and there is strong evidence that these represent equilibrium concentration and not merely an accumulated in-process inventory resulting from recycling the solutions for many years. Consequently, it is believed that uranium could be recovered at a constant rate as long as mining and leaching operations continue. Preliminary surveys and estimates by the USBM indicate a production potential of possibly 1000 tons of U3O8 per year at a cost of less than $8 per lb if the major process streams from most of the large copper mines in the western United States were to be treated. Laboratory research by the USBM showed that the uranium could be efficiently recovered as a specification-grade uranium concentrate by a combination of ion exchange resin and solvent extraction of liquid ion exchange techniques. A joint pilot plant investigation by Kennecott Copper Corp. and the USBM was conducted on solutions from the Bingham Canyon mine to evaluate a new system of countercurrent ion exchange developed during the laboratory studies. In subsequent small-scale continuous tests, recovery of uranium from the pregnant eluate by solvent extraction and chemical precipitation techniques was investigated.

Jan 1, 1968

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By Harold Markus, Gerhard Derge, Arthur Grobe

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from ½ to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.1°. Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

Discussion of the paper of GEORGE S. RICE and H. H. CLARK, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2563 to 2571. NORMAN V. BRETH,* Pittsburgh, Pa.-It was my privilege to visit in the last two months on behalf of the U. S. Bureau of Mines 10 mines where electric shot-firing systems controlled from outside the mine are installed. I will describe briefly what I saw in some of these mines, which are located in Utah, New. Mexico, Oklahoma, Alabama, and Kansas. At a mine in Utah, 230-volt alternating current is used to fire the shots, which is taken from a small transformer in the substation. The shot-iring circuit is independent of all other wires and is tested for grounds every day. There are no lightning arresters on the firing circuit. Porcelain insulators are used inside of the mine, and glass outside. The switches are situated as follows: One in the substation, one in, the shot-firer's cabin, two at each cross entry; where the shot-firing circuit crosses the trolley wire a switch is placed on either side of the entry in series with the shot-firing circuit. The miners are checked in and out of the mine. The coal is undercut and is shot down with permissible explosive, the shots being connected in multiple. There are 75 to 110 shots fired each day. A great many times there are no missed shots. If not more than two or three are missed they are left until next day. The fan is kept running at full speed when the shots are fired. The shot-firing switch is closed only once and the whole mine is shot at once. At another mine in Utah, power wires are used for shot-firing circuits; 500-volt, direct current is used to fire the shots. The only sizes of wire used outside of the power wires are Nos. 8 and 14 B. & S. gauge. The return is connected to the pipe lines and track. Porcelain insulators are. used inside of the mine.

Jan 4, 1915

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of' (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.'-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "'12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger's terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By C. R. Boyd

The region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron,........58.15 Water,.........12 96 Alumina,........2.32 Silica,.........1.09 Phosphorus,.. none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows :

Jan 1, 1880

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962