Search Documents

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges'' as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952

By Robert Mehl

IN examining the progress of metallurgical science, the critic must remember that most of our present knowledge of metals and alloys has been accumulated through the needs of industry and commerce rather than through the desire and efforts of a large body of scientists interested primarily in developing a science of metals. The progress of metallurgy, scientifically speaking, has been irregular, and little given to the exhaus-tive exploitation of important scientific fields. The experienced engineer now recognizes the need for the development of the basic science upon which his engineering rests. In addition to the increase in knowledge which results from the normal requirements of industry, a development of the basic science of the behavior of metals and alloys is as desirable in metallurgy as in any other branch of science and engineering. The continued growth of the science of metals-as of every other science-requires studious attention to the principles that underlie the behavior of matter, with the result that knowledge in the several fields of interest should continue to increase. Among the various subjects recognized as important in physical metallurgy few have a wider significance than that of diffusion in solid metals. The phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this, the process of diffu-sion is of first importance practically. The formation of alloys by the annealing of mixed powders, first practiced by Faraday and Stodart81 in 1820 and in more recent years investigated by Masing187,189 and others, has led to the development of special alloys like Carboloy, Vascoloy-Ramet, Genelite, Elcon68, and has recently been applied to the production of noble-metal alloys for electrical contacts"'.

Jan 1, 1936

By Henry Lloyd Smyth, J. Ralph Finlay

The most important area of the so-called Keewatin rocks of northern Minnesota is that which runs westerly from Lake Saganaga, near the national boundary, and finally disappears beneath the drift (or has not been farther traced), in the neighborhood of Vermilion Lake. With this belt we have a general acquaintance, extending back some four years. During the past year we have had the opportunity of studying in considerable detail a small part of it, embracing an area of about 12 square miles on the south and east shores of Vermilion Lake. In this paper we desire to record our observations and conclusions, which seem to us important. II.—Literature. Outside the Minnesota Geological Survey, the list of the investigators who have studied the geology of the Vermilion Lake area is not long. Whittlesey, in 1876,* mentioned the occurrence, in the area about Vermilion Lake, of rocks resembling the Canadian Laurentian. Chester,? in 1884, described the iron-ore at Vermilion Lake as occurring in connection with jasper and quartzite, intimately bedded with the country-rock, chiefly sericite schist, and standing in a nearly vertical attitude. The Vermilion iron-bearing rocks, and those of the Mesabi range, he says, are of the same age.

Jan 1, 1896

MISCELLANEOUS U.S. 0,029,598 - Extraction of vanadium values from vanadiferous iron oxide ore. A pelletized mixture of ore, limestone and bentonite is roasted in an oxidizing atmosphere to form calcium vanadates, the calcine ground, the ground material leached with aqueous ammonium carbonate or sodium carbonate to produce a vanadium-rich solution while leaving an insoluble residue of calcium carbonate and/or calcium bicarbonate along with undissolved iron values, and the solution separated and treated for its vanadium content. This patent is a reissue of U.S. Patent No. 3,853,982, dated Dec. 10, 1974. C. B. Bare and J. W. Pasquali, assigned to Bethlehem Steel Corp. Mar. 28, 1978. 7 pp. (423-68). Filed: 3-3 1-77 (783,352).

Jan 1, 1979

By Graham Bright

Metal mines were developed long before coal mines and the early lighting of underground workings was effected by torches and candles. The early coal mines were outcrop workings and little trouble was experienced from gas, but as the mines became deeper and shaft mines were opened it became apparent that an open-fame lamp was exceedingly dangerous where gas occurred. No satisfactory way of lighting gaseous coal mines was found until Sir Humphrey Davy brought out his famous safety lamp in 1815. The introduction of the Davy lamp was a great step forward but it was unsatisfactory from a light standpoint because the gauze absorbed a large percentage of the light given out by the flame. Clanny corrected this by the introduction of a cylindrical glass lens, which not only permitted a free distribution of the light from the flame but added greatly to the safety by eliminating the possibility of the flame coming in contact with the gauze and by protecting the flame against air currents. A very complete story of the flame safety lamp since its inception is given in the U. S. Bureau of Mines Bulletin No. 227, by J. W. Paul, I;. C. Ilsley and E. J. Gleim, published in 1924. A little more recent publication, known as Safety in Mines Research Board Paper No. 4, entitled "The Light Power of Flame Safety Lamps," by R. V. Wheeler and D. W. Woodhead, was published in England in 1927. The flame safety lamp was the only lamp available for gaseous mines for about 100 years. Although the incandescent electric lamp has been in use over 50 years, it was not found safe to use this lamp from wired circuits in gaseous locations. The storage battery was advocated shortly after the development of the incandescent lamp but until the introduction of the tungsten filament in the miniature mine-lamp bulb, the battery lamp was not a real possibility because of the excessive weight of the battery necessary to produce a sufficient amount of light. The actual development of the electric-battery type of lamp took place largely between 1910 and 1915. In England and Europe, the developmenb was almost entirely along the

Jan 1, 1936

By Graham Bright

Metal mines were developed long before coal mines and the early lighting of underground workings was effected by torches and candles. The early coal mines were outcrop workings and little trouble was experienced from gas, but as the mines became deeper and shaft mines were opened it became apparent that an open-fame lamp was exceedingly dangerous where gas occurred. No satisfactory way of lighting gaseous coal mines was found until Sir Humphrey Davy brought out his famous safety lamp in 1815. The introduction of the Davy lamp was a great step forward but it was unsatisfactory from a light standpoint because the gauze absorbed a large percentage of the light given out by the flame. Clanny corrected this by the introduction of a cylindrical glass lens, which not only permitted a free distribution of the light from the flame but added greatly to the safety by eliminating the possibility of the flame coming in contact with the gauze and by protecting the flame against air currents. A very complete story of the flame safety lamp since its inception is given in the U. S. Bureau of Mines Bulletin No. 227, by J. W. Paul, I;. C. Ilsley and E. J. Gleim, published in 1924. A little more recent publication, known as Safety in Mines Research Board Paper No. 4, entitled "The Light Power of Flame Safety Lamps," by R. V. Wheeler and D. W. Woodhead, was published in England in 1927. The flame safety lamp was the only lamp available for gaseous mines for about 100 years. Although the incandescent electric lamp has been in use over 50 years, it was not found safe to use this lamp from wired circuits in gaseous locations. The storage battery was advocated shortly after the development of the incandescent lamp but until the introduction of the tungsten filament in the miniature mine-lamp bulb, the battery lamp was not a real possibility because of the excessive weight of the battery necessary to produce a sufficient amount of light. The actual development of the electric-battery type of lamp took place largely between 1910 and 1915. In England and Europe, the developmenb was almost entirely along the

Jan 1, 1936

By T. D. Murphy

The element silicon, with its usual partner, oxygen, plays the same role on this planet relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO,) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO, tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide SiO, (analogous to its congener carbon in CO and CO,); a tetrachloride SiCl, (analogous to CC1,); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117°- 200°C but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures-such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao, et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert, et al., 1973; Pecora, 1960).

Jan 1, 1975

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By L. F. Terry, H. K. Ihrig, D. J. Sabin, Ralph E. Davis

This paper presents the results of a study of the comparative values of the several fuels commonly used by industrial plants. It shows that the energy actually recovered from any fuel and turned into useful work is dependent upon several factors: (1) the total energy available in the fuel, (2) energy losses resulting from combustion reactions and (3) energy losses dependent upon the mechanics of the firing operation. The chemistry of combustion and the losses resulting therefrom are discussed. The Advantages and disadvantages of the several mechanical methods of firing and the resulting heat losses in each are developed. Data obtained from several typical fuel operations, where careful records have been maintained, are presented to show that the practical results in the actual operation are in harmony with the theoretical results developed in the earlier part of this paper. Water power and solid, liquid or gaseous fuels are at present the only commercial sources of energy. The economic utilization of any one of them depends, in the final analysis, on the cost of energy per unit of finished product to which the energy is applied. The location of the plant utilizing the particular fuel chosen is a large factor in the original choice. The cost per unit at its original natural source, or even in its delivered form, is not always the final measure of its worth. The use of electricity as a source of energy illustrates this to the extreme. Electric current produced from water power is very cheap in certain localities. In Norway, current is sold as low as ½0# per kw-hr., while in dry cells it costs as much as $10 per kw-hr. Yet the sale of dry cells is a large business. The selling price of gas also varies widely. In some localities natural gas for the manufacture of carbon black sells for as low as $0.02 per million British thermal units, while artificial gas for domestic purposes sells for as high as $6 per million B.t.u. Obviously the cost per unit of energy is not the final determining factor in its purchase. Any discussion of the economic utilization of fuels must include costs in relation to the units of finished material manufactured. In large central power generating stations, this is the over-all cost per kilowatt-hour, and in ceramic firing the cost per unit of finished product of a certain quality is the criterion of economic utilization.

Jan 1, 1931

Jan 1, 1951

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to begin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTURES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, depending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1951

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Ivor Jenkins

Processes employing 'controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,' but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By John S. Marshall

The purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bituminous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper. Mining Methods and Equipment The mine is in the vicinity of Wilkes-Barre, Pa., in the Buried Valley area of the Susquehanna River. Seven veins were mined, varying in thickness from 18 in. to 8 ft. The cover overlying the veins varied from 200 to 800 ft. Three-fourths of the 1200 acres of property was covered with from 100 to 200 ft. of water-bearing gravels and clays, which prevented first mining under rock cover less than 50 ft. and pillar removal under rock cover less than 100 ft. The property was opened by two shafts sunk on the mountainside to avoid the sand and gravel present in the river valley. The veins dipped an average of 5" from the shafts. In certain areas the veins were practically flat and in some places a reverse pitch as high as 5" was encountered for short distances. A daily output of 3800 tons was hoisted on a two-shifi; hoisting operation. The mining consisted of 75 per cent pillar removal, and of the total production in the later years of operation 80 per cent was loaded by shaker conveyors, chain conveyors and scraper loaders. Shaker conveyors accounted for 70 per cent of the total output; chain conveyors and scraper loaders for 10 per cent. All conveyor work was double-shifted and 25 per cent was triple-shifted. A total of 87 shaker-conveyor units were on the property, of which 75 were kept in operation at all times.

Jan 1, 1940

By Irwin Roman

THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years,1 but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1932

By William P. Blake

Postscript to the paper read by Prof. William P. Blake at the Lake Superior meeting, September, 1904. POSTSCRIPT.*-Since the publication of my paper upon the blackening of the surface of rocks in desert regions, I have noted that similar views of the origin of superficial discoloration in the case of certain rocks from the Salt Lake basin of Utah have been expressed by Prof. George P. Merrill. In the pamphlet, he described the brown-coated weathered boulders from Tooele county, reaching the conclusion that the discoloration was due to the solution of the manganese and iron compounds 'in the interior of the boulder, while they were in the water, and the gradual bringing of this material to the surface through capillarity and its oxidation when exposed.

Mar 1, 1905

By H. Doi, Y. Fujiwara, K. Miyake

In order to throw light on the mechanism of plastic deformation of WC-Co alloys, compressive tests of WC-(7 to 43) vol pct Co alloys have been carried out at room temperature, and stress-micro strain relation has been investigated in detail. The analysis of the factors affecting the yield stresses reveals that the yield stresses can be predicted by modified Oro-wan's theory if one properly estimates the planar in-terfiarticle spacings. Conzpressive straining of some of the alloys by 0.066 to 0.17pct increases the decrements by a factor of as much as 3.4 to 14, whereas the corresponding increase in the electrical resistivities is less than 10 pct. The analysis of the decrement data in terms of -Gramto and Lücke theory shows that the marked increase is attributed to increased dislocation darnping itt the binder (cobalt) phase. By cornbilling the decrement data and the conzjwession duta, one obtains the relation between flow stress in shear (?t) and increase in dislocation density (p): At = const . v6 . This is interHeted to mean that the mechanism of strain hardening of CirC-Co alloys is essentially sarne as the one for dispersion strengthened alloys. The possible effect of bridge formations between the carbide particles has also been examined. OWING to the combination of hardness, strength, and other physical and chemical properties, WC-Co alloys have opened the way for unique fields of applications, the recent ones being, for instance, anvils for super-high-pressure generation apparatuses. In such applications, the alloys are frequently subjected to very high compressive stresses: these stresses may cause the alloys to deform plastically and eventually to fail. However, much remains obscure regarding the nature of the plasticity of the alloys. Evidently, the alloys owe their high strength to the hard carbide particles which frequently occupy as much as 80 to 90 pct in volume fraction, whereas the ductility required for practical applications is provided by the small amount of the binder phase between the carbide particles. When the volume fraction of the carbide phase is not very large, deformation behavior of the alloys may be described by some of the current dispersion strengthening theories. However, greatly increasing the carbide phase is thought to lead to some carbide skeleton structure or bridge formations owing to the increased chances for direct contacts between the carbide particles;1,2 this may appreciably affect the plasticity of the alloys. Regarding the effect of formation of the carbide skeleton structure, it is interesting to note the work by Ivensen et al.3 on compression tests of the alloys containing somewhat large carbide particles; they observe extensive generation of slip bands in the carbide particles after application of some preliminary compressive stresses. They interpret the results in terms of plastic deformatiot: of the carbide particles which are supposed to have formed a skeleton structure; the binder phase plays only a passive role, at least in the early stages of the deformation. That carbide crystals exhibit microplasticity at room temperature is apparent from the work of Takahashi and Freise4 and French and Thomas5 on indentation of WC single crystals. On the other hand, Dawihl and coworkers6-10 maintain that even when volume fraction of the carbide phase is very large (for instance, more than 90 pet), a very thin binder layer generally exists between the carbide particles. They interpret the results of the extensive mechanical tests in terms of the plasticity of such a layer. Gurland and Bardzil11 point out that decrease in ductility of the alloys with increase in the carbide phase is caused by the effect of plastic constraint exerted by the dispersed carbide particles. Drucker12 further develops this concept from a continuum-mechanics approach on an assumption that a continuous thin binder layer separates the carbide particles. A common feature of the studies reported so far on the plasticity of the alloys is that the information deduced is invariably qualitative in nature. Thus, very few systematic experiments for obtaining reliable and sufficiently detailed stress-strain curves of the alloys varying widely in the microstructural features have been carried out. In particular, it may be of special interest to investigate in detail the early stages of the plastic deformation of the alloys in order to shed light on the strengthening mechanism. However, such work appears to be extremely rare. Doi et al.13 recently reported a first brief account of the results of some quantitative analysis of the plasticity of the alloys in terms of dislocation theory. Their experiment was rather limited in the composition range covered (volume fraction occupied by the carbide phase: 79 to 83 pct), and thus they could not necessarily elucidate the controlling mechanism of plastic deformation of the alloys of a more general composition range. Consequently, in the present investigation, deformation behavior and some other physical properties of the alloys were investigated and discussed in more detail over a much wider composition range. SPECIMEN PREPARATION WC-Co alloys used in this experiment were prepared in cylindrical or rectangular form by sintering in vacuo compressed mixtures of tungsten carbide and cobalt

Jan 1, 1970

By Harry V. Welch

This paper presents a brief discussion of numerous devices and processes which have been utilized for the recovery of values from gases in copper reduction works and describes in greater detail the development and application in recent years of electrical precipitation, more familiarly known as the Cottrell process, to the problems of dust losses with furnace gases in copper-smelting and refining plants. The field for collection of suspended particles in gases is widely extended in our modern complex, congested .and industrialized mode of living, and its satisfactory solution is required by our increasing appreciation of the extravagant waste, unhealthful effects and nuisance which such uncontrolled emission of solid suspensions represents. Much of the special dust-recovery equipment in use today has been developed in one industry and carried over to many others. The early work of Cottrell was with sulfuric acid mists, aimed at the purification problem in contact acid manufacture, but the present uses of Cottrell equipment cover a diversified field—carbon black, combustible gas, oil mists, iron blastfurnace fumes and dusts, cement-kiln gases, as well as the purification of gases in contact and chamber acid plants and its wide and extended use in the nonferrous metallurgical field of copper, zinc and lead, and their associated metals. Dust and fume collection from furnace gases became a problem only with the modern development of large and amply powered auxiliary furnace equipment, which in turn permitted large furnace units, fast driving and large outputs of finished product per unit of furnace capacity. The ancient metallurgist with his small clay pot and hand-operated bellows had too little gas velocity to cause a real dust loss. As furnaces grew in size, flues and stacks were added, and undoubtedly the first observable dust losses were indicated by the deposits in the flue and stack base. Large flues, it was noted, collected more than smaller ones, and the expansion of a portion of the flue into a chamber represented the first serious attempt at recovery of furnace dust losses. For a century or more the settling chamber represented the best of skilled metallurgical practice in recovery of furnace dust, and it may be said to have reached

Jan 1, 1934