Search Documents

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By R. Al-Hussainy, P. B. Crawford, H. J. Ramey

The effect of variations of pressure-dependent viscosity and gas law deviation factor on the flow of real gases through porous media has been considered. A rigorous gas flow equation was developed which is a second order, non-linear partial differential equation with variable coeficients. This equation was reduced by a change of variable to a form similar to the diffusivity equation, but with potential-dependent diffusivity. The change of variable can be used as a new pseudo-pressure for gas flow which replaces pressure or pressure-squared as currently applied to gas flow. Substitution of the real gas pseudo-pressure has a nrtmber of important consequences. First, second degree pressure gradient terms which have commonly been neglected under the assumption that the pressure gradient is small everywhere in the flow system, are rigorously handled. Omission of second degree terms leads to verious errors in estimated pressure distributions for tight formations. Second, flow equations in terms of the real gas pseudo-pressure do not contain viscosity or gas law deviation factors, and thus avoid the need for selection of an average pressure to evaluate physical properties. Third, the real gas pseudo-pressure can be determined numerically in term of pseudo-reduced pressures and temperatures from existing physical property correlations to provide generally useful information. The real gas pseudo-pressure was determined by numerical integration and is presented in both tabular and graphical form in this paper. Finally, production of real gas can be correlated in terms of the real gas pseudo-pressure and shown to be similar to liquid flow as described by diffusivity equation solutions. Applications of the real gas pseudo-pressnre to radial flow systems under transient, steady-state or approximate pseudo-steady-state injection or production have been considered. Superposition of the linearized real gas flow solutions to generate variable rate performance was investigated and found satisfactory. This provides justification for pressure build-up testing. It is believed that the concept of the real gas pseudo-pressure will lead to improved interpretation of results of current gas well testing procedures, both steady and unsteady-state in nature, and improved forecasting of gas production. INTRODUCTION In recent years a considerable effort has been directed to the theory of isothermal flow of gases through porous media. The present state of knowledge is far from being fully developed. The difficulty lies in the non-linearity of partial differential equations which describe both real and ideal gas flow. Solutions which are available are approximate analytical solutions, graphical solutions, analogue solutions and numerical solutions. The earliest attempt to solve this problem involved the method of successions of steady states proposed by Muskat.' Approximate analytical solutions' were obtained by linearizing the flow equation for ideal gas to yield a diffusivity-type equation. Such solutions, though widely used and easy to apply to engineering problems, are of limited value bemuse of idealized assumptions and restrictions imposed upon the flow equation. The validity of linearized equations and the conditions under which their solutions apply have not been fully discussed in the literature. Approximate solutions are those of Heatherington et al.. MacRobertsl and Janicek and Katz.' A graphical solution of the linearized equation was given by Cornell and Katz. Also, by using the mean value of the time derivative in the flow equation, Rowan and Clegg' gave several simple approximate solutions. All the solutions were obtained assuming small pressure gradients and constant gas properties. Variation of gas properties with pressure has been neglected because of analytic difficulties. even in approximate analytic solutions. Green and Wilts8 used an electrical network for simulating one-dimensional flow of an ideal gas. Numerical methods using finite difference equations and digital computing techniques have been used extensively for solving both ideal and real gas equations. Aronofsky and Jenkins"I " and Bruce et al.11 gave numerical solutions for linear and radial gas flow. Douglas et al." gave a solution for a square drainage area. Aronofsky 13 included the effect of slippage on ideal gas flow. The most important contribution to the theory of flow of ideal gases through porous media was the conclusion reached by Aronofsky and Jenkins" that solutions for the liquid flow case'" could be used to generate approximate solutions for constant rate production of ideal gases. An equation describing the flow of real gases has been solved for special cases by a number of investigators using numerical methods. Aronofsky and Ferris 10 onsidered linear flow, while Aronofsky and Porter 17 considered radial gas flow. Gas properties were permitted to vary as linear functions of pressure. Recently, CarteP 18 proposed an empirical correlation by which gas well behavior can be estimated from solutions of the diffusivity equation using instantaneour values of pressure-dependent gas

Jan 1, 1967

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

By F. L. Ransome

The following paper aims to present in a much condensed form the salient results of a detailed geological study of the Bisbee quadrangle, Arizona, carried on during the latter part of the year 1902. It is essentially an abstract of the final official report which will shortly appear in the series of professional papers of the U. S. Geological Survey, accompanied by maps, sections and illustrations. I. Geography. The Bisbee quadrangle, which includes the Warren mining district, lies in Cochise county in the southeastern part of Arizona. It is inclosed between the meridians 109" 45' and 110" 00' and the parallels 31" 30' and 31" 201, the latter being locally the Mexican boundarg line. The area of the quadrangle is about 170 square miles, and includes the southeastern half of the Mule Mountains, one of the smaller of the isolated ranges characteristic of this part of Arizona. The Mule Mountains, while less markedly linear than the Dragoon, Huachuca, Chiricahua, and other neighboring ranges, have a general NW-SE. trend. They may be considered as extending from the old mining town of Tombstone to the Mexican border, a distance of about 30 miles. On the northwest they are separated by the broad, flat floor of Sulphur Spring Valley from the Chiricahua Range, and on the southeast by the similar broad valley of the Rio San Pedro from the Huachuca Range. The maximum width of the range is about 12 miles, and its greatest elevation attained by Mt. Ballard, west of Bisbee, is 7,400 ft. above sea-level. An index-map, showing the geographical position of the Bisbee quadrangle, is shown in Fig. 1. The town of Bisbee (Fig. 2), with an estimated population of 6,000, is crowded into a few narrow confluent ravines near the

Jan 1, 1904

[JOSEPHSON, W. G.: The Argonaut Mine of Today, M88, 475 JOUET, C. H., biography, M29, 258 Joule-Thompson effect, 98, 381 JOWETT, J. H., biography, M83, 276 JUDSON, S. A.: Operations in the Gulf Coast of Texas and Louisiana for 1926, G26, 659 JUDSON, S. A., EASTON, H. D. JR. AND SCHAEFFER. W. A. JR.: Estimation of Petroleum Reserves in Prorated Fields 114, 11. Abs., YB35, 50 JULIHN, C. E.: Copper---An Example of Advancing Technology and the Utilization of Low-grade Ores. Brookings Lecture, in Mineral Economics (1931 volume, B. W. Mudd Fund)]

Jan 1, 1936

By Shun-ichi Satoh

The electric arc welding of cast iron has been studied by Braune Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer Candy, Neese, Miller, Carter, American Welding Society, Namack Lebrun, Achenbach, Jansson, Xochendorffer and others.' The write of this paper has been able to obtain a series of cast irons, from gray tc white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (Sic) and graphite (C). In this work, he found the curious phenomenon of barium carbonate.

Jan 1, 1929

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

By Richard H. Olson, Lawrence A. Roe

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% Si02, 31.89% MgO, and 4.75% H20. However, as an industrial commodity, talc rarely approaches theoretical purity. Nevertheless, the impure talc products of commerce find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are tremolite, chlorite, dolomite, mica, and magnesite. Steatite was originally a mineralogical name applied to pure talc. In today's commerce steatite generally refers to the massive variety of talc suitable for electrical insulator manufacture. Block steatite ore can be machined into various shapes. Impure varieties of massive or block talc are still commonly referred to as soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soapstone and talc, this is a natural thing since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as "slip") have been grouped together and called soapstone or talc. Further, there is a mineralogical relationship of pyrophyllite to montmorillonite and talc to hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Indians on Santa Catalina Island, CA. In the mid-1800s, soapstone from deposits along the western foothills of the Sierra Nevada mountains was used by white settlers for building and ornamental stone and in the linings and foundations of furnaces (Anon. 1956). Previous to 1916, the annual recorded production in California did not exceed 2000 tons. In the period 1912 to 1918, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 9,000 to 20,000 tons. In the mid-1930s, the use of talc in wall tile grew rapidly. In California, the production of talc grew to 63,000 stpy in 1943. The post-war building boom helped California production to grow to 120,000 tons in 1951. In 1968, production was 165,000 tons, 1969 was 145,000 tons, 1970 was 185,000 tons, and 1972 was 155,000 tons. Talc mining in New York state dates to about 1878 when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville, New York. In 1893, this operation was sold to the International Pulp Co. which changed its name to the International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc. in 1974. A new talc operation, the Gouverneur Talc Co. owned by the R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 200 stpd (Gillingham, 1950). Subsequent expansions have increased capacity to over 600 stpd. The Vermont talc industry began just after the start of the 20th century. Talc was discovered in the area of the present Johnson, VT, talc mine in 1902. The American Minerals Co. initiated plant operations at Johnson in 1904. The Magnesia Talc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963; Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine has a long history as a producer of talc crayons. The Eastern Magnesia Talc Co. was formed in 1924 by a merger of the Eastern Talc, Co.

Jan 1, 1983

Jan 1, 1951

By T. Egleston

FOR a great part of the progress of the world we are indebted to the works of engineers. It is to them that we owe our means of rapid transportation, our canals, our railroads, our bridges, many of our automatic machines, and most of those appliances which, by facili tating or decreasing the amount of human labor to be expended and by utilizing the great forces of nature, have made the present progress of the world possible. Their education is a matter of momentous interest to the whole civilized world. I have, therefore, thought that some discussion of the theory upon which their education should be based would be of interest to this body, and have ventured a few reflections and suggestions upon the subject. The word education, in its original signification, meant the draw ing out of a man what there was in him. In our common schools the practical work of education consists in putting into the brain a larger number of facts than can be retained, which are consequently more or less understood and digested. It ordinarily consists simply of teaching a round of abstractions or facts which when not assim ilated are not only useless to the individual, but generate careless habits of thought and make more or less untruthful, unfaithful or unsuccessful men. In most of our schools a procrustean system is adopted; all are made to advance upon one general plan, the quick being kept back and the slow dragged on at a rate too great for their power of comprehension. Until within a very few years it has been a theory in common school education that the brain alone should be developed, and that little or no attention need be paid to the train-

Jan 1, 1888

By E. I. Gordon

The electronic pickup tube is the image-to-video signal-converter or transducer in tele vision-like systems. Images may relate to visible light or IR excitation as in conventional TV systems, X-ray excitation as in some medical and production control applications, or electron excitation as in electron microscopy. The latter process is also important in some forms of light or X-ray sensitive pickup tubes as an intermediate step. In virtually all of these devices the image ends up as a stored charge pattern on a suitable target electrode and the video signal is created by periodically scanning the target with a low energy electron beam and removing the stored charge. In a major group of tubes radiation induced conductivity creates the charge pattern. In others, photoemission is used. In this paper an attempt is made to illuminate some of the device requirements placed on materials exhibiting radiation induced conductivity, some of the materials and techniques that are used, and the problems. The emphasis will be on visible light and IR sensitive targets although some attention will be given to X-ray and electron imaging. Photoconducting films as well as diode arrays will be discussed. ELECTRONIC pickup tubes find their greatest use in commercial, entertainment television, and in industrial and educational closed-circuit television. Video telephone systems, such as AT&T's PICTURE-PHONE System will become eventually the greatest user. Military use is also very important. Nevertheless the use of electronic pickup tubes in technology, science, and medicine is assuming ever greater relevance and demands the greatest diversity and perfection in the pickup tube art. Commercial television and closed-circuit television use requires visible light response, high resolution, low lag, and uniform response. Video telephone use requires the same plus extreme reliability, stability, and low cost. Military use emphasizes, in addition, sensitivity, IR response, and ruggedness. (Devices for far IR response will not be considered here.) The use of pickup tubes in medicine and biology emphasizes UV response for microscopy, X-ray response for radiology, and energetic electron response for electron microscopy. Astronomy and nuclear physics demands low light level response, storage ability, and resolution (here the tube is a successful replacement for film). The interested reader might profitably read Advances in Electronics and Electron Physics, vol. 12,' 16,2 and 22A3 and 22B4 for detailed discussion of the use, properties, and technology of electronic pickup tubes. In general, because of the importance of these uses, none of the above properties will be ignored. Nevertheless attention will be restricted to only those imaging devices, called pickup tubes, using a scanning electron beam to dissect the image with a resulting video signal for conventional CRT display. However pickup tubes have become so complex that many of them include components such as image in-tensifiers which would be normally excluded by this restriction. Thus some of the other imaging devices will not be ignored entirely. We will first review the fundamental elements and physical phenomena involved in modern electronic pickup tubes, then the relevant materials and some of the material problems and then an interesting goal yet to be achieved. REVIEW OF PICKUP TUBE PRINCIPLES In all modern television systems using pickup tubes there is an interval called the frame interval, during which the incoming radiation flux is allowed to produce a cumulative effect in the form of a stored charge pattern which is a replica of the radiation image, and a scan interval during which the stored charge pattern is converted into a video signal. The frame interval bears no fixed relation to the scan interval and may be shorter or longer. In conventional, real time television the scan interval including retrace is identical to the frame interval. Integration and storage is the key to the sensitivity of modern pickup tubes, in contrast to earlier tubes such as the image dissector. At equivalent light levels and without integration, the number of photons contributing to the video signal in the image dissector is lower by a factor approximating the number of picture elements in the displayed image, a number of order 10. Statistical fluctuations in the number of contributing photons represent a serious limitation to the attainable signal to noise ratio, resolution and contrast. As a result considerably greater light levels have to be used then in targets which integrate over the full frame period. Thus the crucial elements, common to all modern pickup tubes, are the charge storage surface and the scanning electron beam which is incident on the charge storage surface at very low energy. These are shown in Fig. 1(a). The charge storage insulator is generally very thin with a thickness of several microns or less. The surface of the insulator is held near cathode potential. The backplate potential is held at cathode potential or at a small positive voltage relative to cathode. The combination of storage insulator and backplate electrode is commonly called the "target". In the absence of incident radiation flux the electron beam scans over the storage surface depositing negative charge uniformly over the scanned part of the surface by virtue of the fact that the effective secondary

Jan 1, 1970

By N. P. Goss

ASTERISM appearing in X-ray Laue dia-grams is an extremely sensitive index of changes in the internal structures of indi-vidual grains of polycrystalline metals. It indicates the existence of various forms of subboundary structure or subdivision within the grain. The present viewpoint is that the grain is made up of lattice blocks having substantially the same size and shape.1-4 When these blocks all assume exactly the same orientation, the crystal is perfect and asterism is absent. Cleaves and Thompson5 observed that the hardness of iron is virtually constant over a range of grain sizes. It is quite possible that the subboundary structure caused this, and that the latter is just as important as grain size itself. While the experiments reported here are not con-clusive, they do support this viewpoint. Metals can, under certain conditions, be prepared entirely free from asterism, but this preparation does not necessarily require long heating or slow cooling, as will be shown here. In this paper a distinction is made be-tween mosaic and distorted grain struc-tures but the difference is only a matter of degree. In a previous paper9 it was shown that the grains can become distorted even during heat-treatment. The block structure exists inherently, even in a perfect crystal; the size and shape of these crystallites, or lattice blocks, varies, depending upon a number of factors. Goetz, for example,7 has shown that a metal before crystallizing from the molten state must go through a paracrystalline phase with oriented groups of atoms about 10-14 to 10-15 c.c., or 10 5 cm. in size.

Jan 1, 1940

By Edgar C. Bain

Jan 1, 1932

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910

By Franz Wever

ACCORDING to Tammann,1 the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted-the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes in properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by lowing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By Arthur Crowfoot

INTRODUCTION The principal object of this paper is to present data on the development of the revolving convex round table as a concentrator for the through 0.07-mm. slimes from the ores of the Butte district, although same brief notes on the earliest recorded use of this type of concentrating table in the ore-dressing plants of the Lake Superior region and of the Butte district are also presented. The revolving convex round table belongs to the class of concentrating tables known as film-sizing tables, these tables using the relative transporting power of a film, or thin sheet of water, as it flows over a quiet inclined surface, to separate the minerals of a sorted product.

Jan 8, 1914

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By B. F. Fackenthal

At the session of the Bethlehem, Pa., meeting of the Institute, held in the Durham Cave, at Durham Furnace, on the afternoon of May 20, 1886, I exhibited some specimens of a fibrous white efflorescence which had exuded from the pig-iron at that time being made at Durham Furnace. As some of the members expressed an interest in the matter, I promised to have complete analyses made, and to report the result in a paper to the Institute. The presentation of the paper has been long delayed, but there appears to be no other literature on this subject, and it may still be of interest. The efflorescence was found to exude from the pig-iron where the pigs were broken hot from the sow; the entire fracture of both pigs and sow often being entirely coated with this material. Sometimes there was only a white surface, as if the ends had been daubed with white paint; but in most cases the material was found in small globules and in thin sheets. If the iron had been broken a little too hot, arid in consequence had " bled " on separating from the sow, some of the efflorescence would be found deposited 011 the iron-drippings, and on the incrustations of sand in the pig-bed. The globules were irregular in shape, some of them equivalent in mass to spheres three-eighths of an inch in diameter, but most of them much smaller. The thin sheets were also irregular in shape, and, although they were not porous, were often riot thicker than a spider-web. Some of them were produced by the peeling-off&apos; of the thin coating on the pigs above referred to. They were opalescent in appearance, and some of them had an area equivalent to two square inches; but the largest pieces would fall apart in handling. Several ounces of the efflorescence could often be picked up, or scraped off the pigs, after each cast.

Jan 1, 1901

By Alden Greninger

IN a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form { 133 } . In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form {110}, and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices are body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in mark-ing habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orienta-tion of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix.

Jan 1, 1938

By T. C. Shelton, W. M. Huang

One of the problems arising from the use of modern machines and systems in coal mining is increased emission of explosive gases into the mine passageways. Interest in degasification of coal seams has grown. The authors summarize the results of coal permeability tests done at Virginia Polytechnic Inst. on one of the fundamental aspects of the problem. There are undoubtedly many factors that affect the emission of gas from coal but the permeability of coal to gas flow would seem to be fundamental. However, there is very little information on coal permeability to gas flow available in the U.S. at the present time, despite the fact that such knowledge would appear to be significant in any degasification effort. Studies made recently in the mining engineering laboratories at Virginia Polytechnic Inst. have determined values of permeability on 1-in. cubes of selected coals. COAL PERMEABILITY The permeability values given in this paper are based on adaptations of Darcy&apos;s law formulated by Henry Darcy in I856 from experiments with fluid flow in porous media.&apos; Using air as the gaseous fluid, they were obtained by employing similar methods as are used to dete1:mine the permeability of petroleum and gas reservoir rock specimens. Permeability is. a measure of the ease with which fluids flow through a porous substance, and it is governed by the connected pores within a porous medium. If a few large-sized pores, fractures or channels are present within the medium, the medium can have great permcnability without significant porosity. It is reasonable to assume, therefore, that the permeability of coal, due to its structure, is based on fractures connecting the pore space left as the result of some degree of devolatilization or other changes of the substance from which coal was formed. The results of this irvestigation tend to validate this assumption in that the values obtained indicate a close relationship between the rank and permeability of coal. COALS TESTED AND PROCEDURE The coals whose permeability values were determined in this investigation are given in Table I.

Jan 1, 1962