Search Documents

By S. S. Marsden, S. H. Raza

An experimental study of the flow of line-textured. aqueous foams through Pyrex tubes is described. The foams range in quality F (ratio of gas volume to total volume) from 0.70 to 0.96 and behave like pseudoplastic fluids. At lower flow rates they exhibit laminar flow ad have apparent viscosities which increase with quality, and which cover a range of 15 cp to 255 poise for tubes of 0.25- to 1.50-mm radius rj. At higher flow rates a plug-like type of flow is developed, the extent of which increases with both T and ri. When the same foams flow through either open or packed Pyrex tubes, remarkably high streaming potentials ?E are often generated. These can easily reach 50v if nonionic foaming agents are used, but are at least an order of magnitude less for ionic foaming agents. A linear relationship between ?E and the pressure differential ?p is observed; this usually extrapolates to positive values of ?p at ?E of zero. The slope of the line increases with both F and ri. An equation was derived to describe the streaming potential of non- Newtonian fluids in circular tubes and was used to correlate experimental results. The calculated < potentials are of the right order of magnitude. INTRODUCTION Foams are both unusual and inniguing in their physical properties, and have been the subject of many scientific studies. However, present knowledge of foams is still fragmentary, specific and often contradictory. Apparent viscosity of foam is the physical property of greatest interest to both rheo1ogists and engineers. sibreel reported that the apparent viscosity decreased with increasing shear rate in a manner similar to some non-Newtonian fluids. Penny and Blackman2 reported that fire-fighting foams had both a limiting shear stress and a tensile yield stress. There is little doubt that some foams at least behave like non-Newtonian fluids, and have apparent viscosities considerably higher than those of either constituent phase. The high apparent viscosity of foam with its concomittant effect on mobility ratio and sweep efficiency no doubt prompted several attempts by research groups to use foam as a displacing agent in porous media. Based on recent experience, most of these groups probably succeeded in completely blocking fluid flow in the porous media and then abandoned their efforts. Two groups apparently found the successful combination of experimental parameters at about the same time.3,7 Others have recently added to our knowledge of foam flow in porous media and its use as a displacing agent.8-13 An experimental problem encountered by Fried3 was a transient blockage of foam flow in porous media when distilled water was used to prepare the foam-producing solution. Fried surmised that this was due to an electrokinetic effect and he eliminated it by using electrolytes in preparing foaming solutions. He also measured the streaming potential of a number of foams in capillary tubes which he found to be appreciably higher than those obtained when the constituent liquid flowed under comparable conditions. This paper presents results of a more comprehensive study of the streaming potential generated by aqueous foam flowing in both open and packed Pyrex tubes. It also adds to knowledge of the rheology of these foams as deduced from their flow behavior in open tubes. APPARATUS AND PROCEDURE A diagram of the apparatus used is shown in Fig. 1. Details of its construction, testing and use are described elsewhere.14 Careful selection of materials, extreme cleanliness and rather elaborate electrical insulation and shielding were necessary to obtain reproducible results (±5 percent). Both streaming potential and streaming current were measured with an electrometer. The design of the foam generator developed for this work is novel (Fig. 2). It will produce uniform fine-textured foams at pressures sufficiently

The following list contains the names of members whose death notices have been printed in MINING AND MDTALLURY from April 5. 1944 through March 15. 1945, Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns. [ ]

Jan 1, 1946

By Lucius W. Mayer

The iron-mines of the Ilsede Hütte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bülten. The Ilsede Hütte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bülten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bülten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; S, 0.02 to 0.09; and CaCO3, 40 per cent. Directly above the conglomerate is limestone, b, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to, 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It clips approximately 10° S.E., and strikes N. 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at G, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine was essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Sep 1, 1908

By N. A. Gokcen, M. N. Dastur

In metallurgical process industries a knowledge of true melting and casting temperatures is very essential for increasing the operating efficiency as well as improving the quality of the finished product. Optical pyrometers are widely used for the purpose because of their cheapness and ease of operation. It is an unfortunate fact, however, that this mode of measuring temperature entails a source of severe error inasmuch as with all non-black bodies, the temperature observed is always below the true temperature owing to deficient emissive power. Hence, the need for emissivity correction arises. In 1913 Bidwell1 obtained emissivity values of 0.36-0.48 for a temperature range of 1520-1800°C. He measured the true temperature of molten iron by sighting into a carbon cavity immersed in the iron under an atmosphere of hydrogen. In 1914 Burgess2 determined the emissivity of a smooth surface of liquid iron free from oxide to be 0.37 under an atmosphere of hydrogen. He claimed to have attained an accuracy of within 5°C at 1500°C with an optical pyrometer using monochromatic light. He reported that no difference appeared to exist between the emissivities of pure iron and of steels containing considerable percentages of carbon, nickel or manganese; nor was there any appreciable variation of emissivity with temperature from 1530 to 1571°C. Wensel and Roeser3 found an elnissivity value of 0.4 for temperatures above 1375°C for cast iron. The average emissivity value for carbon steels reported by Leiber,4 odd,5 Hase6 and Umino7 range from 0.4 to 0.45. Knowles and Sarjant8 made an extensive study of emissivity of molten iron and steel over a wide range of workshop and laboratory conditions. Observations of true temperature were made with immersion thermocouples, and correlated with apparent temperatures indicated by optical pyrorneter readings taken on the pouring stream as it passed over the lip of the crucible. The emissivity of Armco iron was shown to be of the order of 0.4, rising slightly with increasing temperature. But for plain carbon steels containing up to 1.0 pct carbon the emissivity was shown to fall slightly with increasing temperatures. The results of their investigation are in agreement with those of Guthmann.9 Naeser,10 Spencer," Todd5 and Hase6 in regard to the relation between emissivity and temperature for plain carbon steels. However, Goller12 has found a rise of emissivity with increasing temperature for the same steels. Results of several investigations are given in Fig 1. Measurement of True and Apparent Temperatures The necessity for an accurate optical temperature scale for liquid iron in studies of gas-metal equilibria led to this investigation. Experimental measurements were carried out in the induction furnace used by Dastur and Chipman13 in their studies of the reaction of hydrogen with oxygen in liquid iron. The furnace as modified for this work is shown in Fig 2. The atmosphere of the furnace was a mixture of purified argon with hydrogen containing a small controlled amount of water vapor. Gases were preheated by means of a platinum-10 pct rhodium resistance coil. The stream of hydrogen sweeping across the surface of niolten iron vir-

Jan 1, 1950

By George Kunz

(Butte Meeting, August, 1913.) . THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World&apos;s Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact. that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it-would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct. weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.2

Jan 7, 1913

United Engineering Trustees, Inc. W. D. B. MOTTER JR., &apos;44 A. L. QUENEAU, &apos;41 ALBERT ROBERTS, &apos;43 The Engineering Foundation GEORGE D. BARRON, &apos;44 F. F. COLCORD, &apos;42 A. L. QUENRAU, &apos;41 Engineering Societies Library Board A. T. HASTINGS, &apos;41 J. W. LAIST, &apos;44 A. B. PARSONS, EX-Officio T. T. READ, &apos;42

Jan 1, 1941

By Edmund Newton

The steel industry of the United States has depended in the past almost wholly upon imports for its supplies of manganese. Many of the important domestic sources yield ores leaner in their natural condition than the foreign ores the steel industry. has been accustomed to use. To make them available, therefore, either the ores must be concentrated or the practice of the steel industry modified. Roughly 25,000 T. annually of high-grade manganese ores are used for dry batteries for chemical purpose, and in other ways; while approximately 750,000 T. are required for making steel. , By present practice, every ton of steel takes an average of about 14 lb. (1.8 kg.) of metallic manganese. This is generally added to the steel in the form of an alloy, the standard alloys being the 80-per cent. ferro-manganese and the 20-per cent. spiegeleisen, During the year 1917, 286,000 T. of ferromanganese and 193,291 T. of spiegeleisen were made in this country, the former largely from imported ores; and 45,381 T. of ferromanganese. was imported. The metallic manganese represented by these alloys was 304,000 T., the product of roughly 800,000 T. of high-grade ore and 345,000 T. of low-grade ore. Manganese Deposits in the United States Before the war manganese ore was mined in relatively small quantities in the Appalachian region, including Virginia, Tennessee and Georgia, and in Arkansas, but owing to the increase in prices during the past three years manganese mining has been undertaken also in Montana, California, Arizona, New Mexico, Nevada, Utah, and Minnesota. From data now available it appears that in this country deposits of high-grade manganese ores are usually small, while materials lower in manganese and higher in iron occur in appreciable quantities. Our total quantity of manganese-bearing material is relatively large, but on

Jan 1, 1920

By W. Crafts, J. L. Lamont

Electrolytic extraction of carbides from quenched and tempered steel and their examination under the electron microscope were found to be helpful in understanding the mechanism of secondary hardening in alloy steels1 and the same technique has been applied to isothermally transformed steels. A preliminary survey of the utility of the method has indicated that it has promising possibilities for investigating the characteristics of pearlite and bainite. The examination of a few carbon and chromium steels has suggested that pearlite is formed with carbides of two varieties representing the lamellar and nonlamellar forms and that bainite appears to form with a structure analogous to, but significantly different from, martensite. Procedure The method used for examining the carbides was similar to that described previously.1 The chromium steels used in the investigation were made from an Armco iron base in an induction furnace and were not treated with grain-refining deoxidizers. The composition of the steels is given in Table 1. Three-inch square ingots were forged and rolled to 1/8-in. thick sheet for use in the isothermal studies. After rolling, the sheets were sandblasted to remove the rolling scale. Specimens approximately 3/4-in. wide and l1/2-in. long were prepared from the 1/8-in. sheet. They were heated in a salt "bath at 2100°F (1150°C) for 1/2 hour, transferred to other salt baths at 1300°F (704°C), 1000°F (538°C), 800°F (426°C), or 600°F (315°C), held for various periods up to 100 hr and finally quenched in water. After quenching, the specimens were cut in half, one half being submitted to microscopic examination and the other half being used for the electrolytic extraction. The isothermally transformed specimens were submitted to examination under the light microscope to determine the degree of transformation and type of structure and were photographed at 2000 X. Carbide residues were obtained by electrolyzing in 10 pet hydrochloric acid and collecting the residue in glycerine to minimize attack by the acid. As pointed out in the earlier paper, the carbides are attacked to some degree during electrolysis. This attack is relatively minor on the coarser carbides but may be quite severe on the fine bainitic carbides. The residues were washed free of the glycerine with water and alcohol. The alcohol was removed by repeated washings of amyl acetate, and the amyl acetate suspensions were transferred to stoppered vials. Debye-Sherrer X ray diffraction patterns of the residues were prepared using a chromium target. A selection based on the microstructure and X ray data was then made of samples considered most illustrative of the progress of transformation. Electrolytically extracted residues from these samples were submitted to examination by W. D. Forgeng and A. C. Jenkins on the electron microscope at the Research Laboratories of The Linde Air Products Co. and electron micrographs were made at X 5000 and enlarged to 25,000 X. The micrographs obtained with both the light and the electron microscopes are mounted side by side in the accompanying figures. Although no effort was made to establish the T-T-T diagram for the chromium steels, the times for holding in the salt bath were adjusted with the intention of making the samples represent different stages in the transformation at temperatures of 600, 800, 1000, and 1300°F. The degrees of transformation and results of X ray examination are shown in Tables 2—4. The carbide designations refer to orthorhombic or trigonal carbide types and are not meant to imply that the compositions are exactly as indicated. X ray Diffraction Data The occurrence of Fe3C and Cr7C3 in these steels was found to be consistent with published data on comparable chromium steels. Steels A and B with relatively low ratios of carbon to chromium contained Cr7C3 in the pearlitic structures and FeuC in the

Jan 1, 1950

ALABAMA Altoona.-Cain, J. America.-Foreman, J. T. Anniston.-Cowie, L. K. Foster, R. N. Rogers, R. F. White, H. E. Ashland.-Sturdevant, J. C. Bessemer. Ball, E. M. McKenzie. W. C., Jr. Morgan, C. Birmingham.-Abbott, C. E. Adler, J. E. Aldrich, T. H. Aldrich, T. H., Jr. Ashton, J. J. Burgin, G. E.

Jan 1, 1923

GOVERNMENT ESTABLISHES DIVISION OF ENGINEERING Government supervision of employment for technical men has been inaugurated by the United States Employment Service, through the establishment of a Division of Engineering, with A. H. Krom, of Chicago, formerly Secretary of the American Association of Engineers, as Director. War demands on the engineering profession have already caused a serious shortage of men with mechanical designing experience and those with practical experience in chemical engineering. At present the professional organizing mediums reach less than 20 per cent. of the estimated 300,000 technical men in the country. This is not a satisfactory arrangement for war times. All the technical men of the country must be reached and, in addition, all men with technical experience must be carefully registered so that they will be immediately available. The advantages of such a governmental registering and systematizing of employment will be apparent at once, to the engineer. Considering that this is principally an engineer&apos;s war, the importance of Federal direction of distribution and conservation of the technical service of the country is apparent. The Service will he started through the office of the Director of Engineering, 29 S. LaSalle St., Chicago. All technical men desiring to register for emergency Government work or permanent advancement in positions meeting their qualifications, are urged to volunteer at once for registration, classification and employment.

Jan 8, 1918

By P. J. Dean

This Paper contains a comprehensive survey of the known electron-hole radiative recombination mechanisms in the family of III-V compounds. Because of space limitations, the luminescence properties of each III- V compound are not reviewed separately and exhaustively. Instead, the different known types of recombination processes are discussed in turn and exemplified with reference to the III- V compound in which they were first recognized, or are best understood. Electron-hole recombinations usually occur predominantly at impurities or lattice defects either introduced de1iberately or inadvertently present, but radiative intrinsic interband electron-hole recombinations, which occur in perfect crystals, have been observed. Recombination processes which involve the participation of impurities or lattice defects ("extrinsic" recombinations) considered include transitions in which a) free carriers recombine with carriers trapped at impurities ("free to bound" transitions) , b) electrons bound at donor impurities recombine with holes trapped at acceptor impurities ("donor-acceptor pair" recombinations), C) excitons bound to charged or neutral donor or acceptor impurities recombine radiatively (both "resonance" and "two-electron" "bound exci-ton" transitions have been observed), d) excitons bound to neutral donor or acceptor impurities recombine non-radiatively (an example of an "Auger" recombination), and e) excitons bound to impurities with the same number of valence electrons as the host atom which they replace ("isoelectronic " traps) recombine radiatively. In addition, Auger recombination processes involving one or more free carriers have been observed. These extrinsic processes all involve impurities which are present as point defects. Some apparently well-authenticated examples of the recombination of excitons bound to complex impurity-lattice defect centers including nearest-neighbor donor-acceptor pairs are also discussed. Identificalions of the transitions involved in stimulated emission from the direct gap III-V compounds are briefly reviewed. Although the examples of these recombination mechanisms are selected from the III-IV compounds ia this review, these processes have quite general relevance in semiconducting crystalline solids; irrdeed most of them have also been identified in the 11- VI compounds and elernental semzconductors. THE development of crystal growth and purification techniques in recent years and concurrent advances in the understanding of physical processes in solids has accelerated the development of a wide variety of solid-state electronic devices of proven utility. These de- vices are generally used for switching or amplifying operations in electrical circuits. Most solid-state circuit elements are very photosensitive. This photo-sensitivity is generally undesirable and the single-crystal chip forming the active portion of the solid-state device is mounted in an opaque container. The photosensitivity is made use of in phototransis-tors and photodiodes, which are among the most sensitive detectors of electromagnetic radiation particularly in the near infrared.&apos; In these devices, light is converted into electrical power. The solid-state lamp utilizes the inverse effect, namely the conversion of electrical power into light. There is an increasing tendency to use single-crystal diodes rather than the earlier electroluminescent cells in which the active material is present as a powder embedded in a suitable dielectric.&apos; The radiation is emitted at a rate far in excess of the thermal equilibrium rate for the frequencies and temperatures involved; i.e., luminescence occurs. The development of practically efficient solid-state lamps is at an early stage compared with solid- state circuit elements or even photodetectors. Considerable progress has been made in recent years, however.3 The present review is devoted to a survey of the radiative recombination processes in the semiconducting compound crystalline solids formed from elements in groups I11 and V in the periodic table. These materials exhibit the full range of known recombination processes in solids. In fact many of these processes were discovered in 111-V semiconductors. Nonradiative recombination processes, which control the lutninescence efficiency, are also discussed. Luminescence is efficiently excited in semiconductors through processes which produce large excess concentrations of free electrons and holes in the energy bands of the crystal. Transitions induced by lattice defects or impurities usually predominate in the recombination process. By contrast, luminescence in the conventional fluorescent lamp is excited by optical absorption at the luminescent impurity center itself (the activator) and/or at a second type of impurity center (the sensitizer). This latter type of photoluminescence process, occurring in doped ionic crystals with wide band gaps, is outside the scope of this review.4 I) ENERGY BAND DESCRIPTION OF ELECTRON STATES IN CRYSTALS The energy band description of the energy states available to an electron in a crystal forms the basis of our understanding of the empirical division of crystalline solids into metals, semiconductors, and insulators in accordance with their electrical and optical properties.&apos; Nonmetallic crystals have a finite energy gap between the highest energy band which is

Jan 1, 1969

By N. B. Davis

I . INTRODUCTION WHILE working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity, This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 2, 1915

By T. H. Courtney, G. W. Pearsall, J. Wulff

The mechanism, of the decrease in transition temperature of Nb3Sn was studied. Presintered Nb3Sn powder compacts were heated in a dynamic vacuum at elevated temperatures. Loss of tin resulted from these heat treatments and transition temperature as a function of tin loss was discontinuous at a critical value of tin loss. In general, decreases in transition temperature were correlated with deviations from AS a class, the A15 structure-type (also known as Cr3O or ß W) compounds have the highest superconducting transition temperatures.&apos; In this class are stoichiometry and presence of vacancies in niobium sites. The effect of vacancy distribution on the physical properties of Nh3Sn is considered. It is concluded that the close-packed atomic A chain in the A3B A15 structure must be preserved both in coutinuity and direction if good superconducting properties are to he obtained. tempting to associate these high transition temperatures with the most unique crystallographic feature of the A3B structure: the three close-packed, orthogonal chains of A atoms.&apos;0"&apos; There are at least three principal mechanisms by which the perfection of these "A-atom chains" could be interrupted: changing stoichiometry, inducing disorder, or introducing vacancies. Departures from stoichiometry in either direction in V3Ga lower the transition temperature.7&apos;8 In niobium-

Jan 1, 1965

By C. R. Garr, A. R. Troiano

FLAKING or hair-line crack formation has been a major problem confronting the producer of large alloy steel forgings.&apos; Today it is generally conceded that hydrogen in one or more forms in alloy steel sections is a requisite for flaking. Hence an obvious remedy is a thermal cycle that reduces the hydrogen content to some low level. In practice, this generally means holding the material at some subcritical temperature for a period of time depending on the size of the ingot or forging. Another method that will suffice in some cases is to cool large forgings slowly, i.e., bury in ashes. In practice, this hydrogen bake is sometimes accemplished inadvertently by a series

Jan 1, 1958

By Donald R. Mason, Daniel F. O’Kane

DIFFERENTIAL thermal analysis measurements have been used to determine the ZnTe-In2Te3 pseudo-binary phase diagram. Since ZnTe and In2Te3 are both semiconductors, any intermediate compounds formed in this system should also be semiconductors according to the rules delineated by Mooser and pearson.1 The compound ZnIn2Te4 was first reported by Hahn et a1.2 and it has subsequently been prepared and characterized electrically by several workers. A brief summary of this work has been presented by Mason and O&apos;Kane3 who also report that the compound appeared to melt peritec-tically. The Zn-Te phase diagram has been investigated by Kulwicki4 who found that ZnTe has a melting point of 1290° + 2°C. The In-Te diagram published in Hansen&apos; contains significant errors, and has been redetermined by Grochowski et al.6 However, both sources agree that the melting point of In2Te3 is 667°C, with the latter authors reporting the previously observed solid-solid transformation occurring at about 550°C. Hahn ef al.2 reported lattice-parameter values for the ZnTe-In2Te3 system. The 67 mole pct ZnTe-33 mole pct In2Te3 composition was the only

Jan 1, 1965

President MRS. THOMAS T. READ 9 Windmill Lane Scarsdale, N. T. First Vice-President MRS. FELIX E. WORMSER Acorn Lane Larchmout, N. T. Second Vice President MRS. W. SPROTT BOYD The Carlyle, Madison Ave. and 76th Street New York, N. Y. Third Vice-President MRS. LOREN W. KEMP El Chico, Plainfield Avenue Metuchen, N. J.

Jan 1, 1944

By R. S. Shoemaker, F. W. McQuiston

CAMPBELL RED LAKE MINES Balmertown, Ontario 1974 Operating Data MINE LOCATION: Balmertown, in Red Lake mining area of Ontario TYPE OF MINE: Underground mine developed by vertical shaft to 4300 feet. Mining active above 3000 ft depth. ORE DESCRIPTION: Gold and minor silver.. Sulfur content about 1.3%. Ar senopyrite , pyrite, pyrrhotite, and stibnite. CAPACITY IN TONS124 HRS: 825 ASSAY: 0.66 oz Au per ton heads MILL PROCESS: Amalgamation, flotation, roasting of concentrate and separate treatment of calcines and flotation tails by cyanide. PLANT BUILDING: Mine mill and service facilities all housed in insulated and heated buildings POWER: Total consumption, mine and mill - 100 Kwh/T WASTE DISPOSAL: Impoundment of tailings. Arsenic to sealed underground storage EMPLOYEES: Total of 300 men on payroll. Housing in Balmertown and nearby communities.

Jan 1, 1975

By F. W. Sperr

The byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.).............................. 69 per cent. of coal Domestic coke (1/2 to 3/4 in.)................................ 2 per cent. of coal Breeze (under 1/2 in.)...................................... 4 per cent. of coal Surplus gas, cubic feet per net ton........................... 6600 Gas for heating ovens, cubic feet per net tor i................. 4400 Tar, gallons per net ton.................................... 9 Ammonium sulfate, pounds per net ton....................... 25 Benzols, gallolls per net ton................................. 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke," (&apos;beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writeri stated that in brass-foundry practice, Connellsville coke is considered rnuch superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in making general statements like these. The percentage of sulfur in coke depends largely on that in the original coal, and byproduct coke from a

Jan 1, 1921

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:&apos; I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,&apos; E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940