Search Documents

In response to Dr. Ledoux's paper, a large number of metallurgical establishments and individual assayers expressed their willingness to co-operate in the plan he proposed. The necessary samples were prepared as follows : Matte.—A car-load of matte was put through a Blake crusher, then automatically subdivided into tenths by a Taylor and Brunton sampler, and one-tenth passed through Cornish rolls and through a 12-mesh screen. This was again subdivided by an automatic sampler into tenths, and a final tenth, representing 1 per cent. of the original lot, was finished by hand-sampling on an iron floor until 100 pounds remained. This was pulverized to pass a 40-mesh screen and then thoroughly mixed and divided in the presence of my assistant for distribution to the parties co-operating. Copper Borings.—These were taken from a lot of anodes, the dip-samples from several batches having been united, remelted and cast into a plate, which was proved by assay to be of uniform quality in its different parts. Borings from this plate were intimately mixed and divided in the presence of my assistant. Samples were sent out November 1,1894, with the following letter: New York City, November 1, 1894. Samples of matte and copper (about I pound each) carefully prepared in the presence of my assistant and sealed with his seal as below, are sent you by express for assay and report according to the plan of Dr. Ledoux. These samples are constituted about as follows: Matte. Copper. From. To. From. To. Copper, per cent.,.....50 60 ..........., Gold, oz. per ton,.....2 3 0.20 0.50 Silver, oz. per ton,.....100 150 140 180

Jan 1, 1896

By Cyril Stanley Smith

ON the 6th of February 1684, Dr. Martin Lister mentioned at a meeting of the Royal Society1 that "brass is magnetical," and promised to give an account of that assertion at some other time. He repeated his promise but never fulfilled it, and it was left for William Arderon2 to show, in 1958, that brass could be made magnetic by hammering and that it would retain polarity after magnetizing. Twenty-seven years later Cavallo3,4 examined the matter in great detail. Working with cast calamine brass, he showed that it could be made magnetic by hammering and nonmagnetic by subsequent annealing at a red heat. He found that annealing at a very high temperature caused the samples to lose their magnetic quality permanently, even after subsequent cold-working, but that remelting and cold-working restored it. He encountered some samples of brass that could not be rendered magnetic by any treatment. Experiments in which these were remelted with iron additions gave negative results, and Cavallo concluded that iron impurity was not the cause of the magnetism. He worked with 50-grain (3-gram) samples melted under the blowpipe, hence cooled very quickly. Bennet5 made whole crucible charges from copper and zinc, and found the resulting brass ingots to be magnetic only when iron had been added and then only after cold-working. All these observations applied to material in the cast condition, in which coring would produce a continuous spectrum of composition and cooling would result in varying degrees of precipitation. This knowledge of the subject seems to have been forgotten in the nineteenth century. The older brass was made by the calamine process and frequently contained iron in amounts of 0.5 per cent or more, absorbed from the impure ore with which the copper and charcoal were heated in making the brass. When metallic zinc became available in commercial quantities, calamine brass gradually disappeared, and with it the knowledge of its curious magnetic properties. Only when sensitive apparatus replaced the compass needle of the earlier investigators could the effects be detected in relatively pure metal. The effect of cold-working in inducing ferromagnetism was rediscovered by Bitters in 1930 in a sample of impure copper, and this was confirmed by Lowance and Constant,9 Honda and Shimizu, 10,11 and others. In the same year, Tammann and Oelsen12 showed that copper-rich copper-iron alloys after certain heat-treatments could be rendered ferromagnetic or made more strongly ferromagnetic by cold-rolling. Kussman and Seeman13 showed that the change of susceptibility of relatively pure copper on cold-working was associated with the iron content, and concluded that actual precipitation of iron was caused by cold-working, which is a satisfactory theory until one considers the improbably high rate of diffusion that this would involve. When studying precipitation phenomena in

Jan 1, 1941

By T. Yoshioka, Paul A. Beck

SILICON, germanium, and tin occur with both the white tine-type structure and the diamond cubic structure. In the latter form these elements are semiconductors; in the former they are metallic. The metallic form of germanium and silicon is obtained only under high pressure.' For all three elements the transition from the semiconductor to the metallic state is accompanied by a decrease in the atomic volume of somewhat more than 20 pctily2 Table I. At such a large compression the widening of the s and p bands is sufficient to make the energy gap of 1.1 ev, or less, of the semiconductor disappear, giving rise to the metallic state.*

Jan 1, 1965

By Walter von der Linden

A description is presented of the mining conditions of four longwall shield type support installations in the Pittsburgh seam in northern West Virginia and southwestern Pennsylvania. Details of roof control and operating procedures, production and performance data, and equipment description and basic engineering specifications are given for these four longwall installations. The range of mining heights was between 150 and 250 cm (60 and 95 in.). The major accomplishment of the shield supports in all four faces was the provision of an almost 100% availability for coal cutting; i.e., the face-down time due to roof control problems and support maintenance requirements was minimal.

Jan 1, 1978

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By Earl R. McMillan

Though much has been written during the past several years about the Russian success in using hydraulic jets for coal mining, little or none of the published information, in so far as this writer has observed, has been of any use or practical application in this country. It is true, according to their published reports, that the Russians were pioneers in the use of high-pressure water jets in the mining of coal. They report the use of water jets for this purpose as early as 1936. However, according to a survey of foreign literature on the subject made by the U.S. Bureau of Mines1 a few years ago, water jets in the USSR, as well as in other nations including New Zealand, Poland and West Germany, were used principally to sluice the loosened coal after it had been previously drilled and blasted, rather than to cut or break it from the solid face. The interest of the Northern Pacific in the potential application of a high-pressure water jet to the actual extraction of coal, particularly in steeply dipping beds, originated in a visit by this author to the operations of the American Gilsonite Co. at Bonanza, Utah, in March 1958. After seeing the extraction, on a commercial basis, of gilsonite from a 22-ft wide vertical vein of this solid material with a 3/8-in. diam stream of water under approximately 2200 psi, it was felt that, with some modifications, water jets were the solution to the problem of economically mining the steeply dipping (i.e., steeper than 20º) coal beds in the State of Washington.

Jan 6, 1962

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Papers in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J--Mineral Industry Education Division, K¬-Mining Administration, and 1-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed or mimeographed are available but only on request.

Jan 1, 1944

By R. L. Blackwood

The solid inclusion cell for absolute in situ stress measurement has been found to give reliable results in coal. The cell is described briefly, along with the methods of installing, overcoring and taking readings in underground coal mines. The validity of the cell performance is demonstrated by reference to the stress-relief curves obtained during overcoring and a three-dimensional B.I.E.M. analysis of the installation to test for stress anomalies deriving from the geometry of the overcoring groove-borehole-cell arrangement. Case studies of two stress measurement projects using the cell are presented for coal mines in New South Wales, Australia.

Jan 1, 1982

By F. E. Calkins

THE following presentation of the more important accumulated facts and probabilities involved in copper ore deposition is based on my experience in examination work and study of the extensive litera-ture of the subject; to make personal mention of all sources of information would require the naming of a small army of able geologists and other investigators who have contributed to, building up the science. I have tried to present the salient features of the subject in logical order and condensed form, and to point out the relative importance of processes involved. Doubt-less many geologists could suggest some changes and many additions. ORIGINAL SOURCE The original source of all copper was in the earth's interior; it has been brought to the outer part of the earth, within reach of man, in three ways: (1) By intrusions and flows of basic igneous rocks containing copper in minute quantities, presumably as silicate or sulfide. No orebodies have been formed by this method. (2) As segregations within intrusive igneous rocks, the copper minerals having solidified at the same time as the rock itself. The few deposits known to have been formed in this manner have been of little or no importance. The oft quoted Sudbury nickel-copper deposits are now known to belong to the class following. (3) By gaseous or liquid aqueous emanations from ,large deep-seated masses of intrusive molten rock. These emanations, or mineral solutions, ascended through zones of connected openings in the earth's crust and dropped their load at points far above their source. Deposits formed in this manner were the primary source of nearly all, if not all, of the world's copper production.

Jan 10, 1923

By G. B. Richardson

WHILE examining a number of curves showing the production of petroleum, the author was impressed by the rather uniform relationship between the cumulative production from the beginning of development FIG. I.-ACTUAL' AND COMPUTED PRODUCTION OF PETROLEUM IN WEST VIRGINIA. down to the time the peak was attained and the estimated total production. The curves examined showed an average ratio of cumulative peak production1 to total production of approximately 30 per cent. FIG. 2.-ACTUAL AND COMPUTED PRODUCTION OF PETROLEUM IN CAT CREEK FIELD, MONTANA. These relations were discussed with C. E. Van Orstrand, geophysicist of the Geological Survey, who investigated the subject mathematically.

Jan 3, 1925

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Papers in Classes C-Iron and Steel Division, D Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J Mineral Industry Education Division, Mining Administration, and L-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed or mimeographed are available, but only on request.

Jan 1, 1946

By J. S. Aronofsky, H. J. Ramey

Potentiometric model studies of the five-spot water flood to determine the influence of mobility ratio upon injection or production histories are described. The results suggest a method for the correlation of data from field pilot tests for the estimation of an effective mobility ratio and its effect upon field water floods. The effect of the well spacing-to-well radius ratio upon production histories is presented. A method of accounting for this factor is suggested. The influence of injection (or production) rates and injection and production well pressures upon production histories is shown. The five-spot well pattern was investigated for water-to-oil mobility ratios of 0.1 to infinity. INTRODUCTION It has been well established that mobility ratio has an important effect upon flood patterns.1,2,3,4,5 It should be equally apparent that injection and production histories must also be influenced by mobility ratio. However, none of the articles referred to above mention the importance of being able to predict the effect of well pressures (or injection rates) during the entire time history of a waterflood operation. A complete description of production histories (the terms "injection" and "production" are synonymous for the steady-state model under consideration) would provide values for well pressures and interface positions at any time for a specified injection rate. conversely, if the waterflood problem is specified in terms of a constant injection well pressure, then it would be desirable to know the injection rate and interface positions at any time. This paper describes the results of potentiometric model studies which were used to analyze the influence of mobility ratio on injection or production histories. A method is presented for calculating production histories over a range of ratios of well spacing-to-well radius. The basic method described in this paper to evaluate production histories is to: (1) determine interface position as given in Ref. 1, and (2) measure electrical current and voltage drop for each interface position. It should be mentioned that the current state of knowledge on flood patterns as affected by mobility ratio shows that significant discrepancies exist between the results of various investigators2,3,4,5. It is beyond the scope of this paper to discuss the reasons for such discrepancies. However, the method of determining production histories presented in this paper could be applied to any of the swept-area patterns presented in the literature. All results given in this paper are based on a set of swept areas obtained by the potentiometric method. Potentiometric analyzer technique is adequately described in the literature, but the basic assumptions involved in work of this nature bear repetition. It is assumed that: 1. A distinct oil-water interface exists in the reservoir; only water is mobile in the region behind the interface (water zone) and only oil is mobile in the region ahead of the interface (oil zone). 2. There is a fixed mobility value, (k/µ) w associated

Jan 1, 1957

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By Carleton C. Long, George F. Weaton

Two years ago the general features of the St. Joseph Lead Company's zine-smelting process were described.' At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtowlz smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the company's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; SiO², 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the coacentrate to a calcine of average conlposition (first 10 months of 1938): Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; SiO², 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07'; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sulphuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in, by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO² to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1943

By George F. Weaton, Carleton C. Long

Two years ago the general features of the St. Joseph Lead Company's zine-smelting process were described.' At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtowlz smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the company's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; SiO², 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the coacentrate to a calcine of average conlposition (first 10 months of 1938): Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; SiO², 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07'; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sulphuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in, by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO² to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1943

By A. A. Dor

Out of nine new major iron ore concentrators put in operation during the last three years, or expected to be commissioned in 1968, seven incorporate primary grinding mills and have a total design capacity of 13,150,000 ltpy of pellets, while only two include conventional rod and ball mill grinding circuits for a total design capacity of about 6,100,000 ltpy (Table I). This evolution in the application of primary grinding to hard, fine grained magnetite ores represents an important development in the technology of mineral processing. It has been the outcome of comprehensive testwork in the laboratory and in pilot plants.

Jan 11, 1968

By J. H. Ffolliott

ALL of the prospects that later became mines in the Ducktown district were discovered prior to 1854, and most of them were exploited before the turn of the century. It is the purpose of this paper to discuss the exploration and current development of the Boyd mine, discovered in 1853. It is in the heart of the Ducktown Basin, in the extreme southeast corner of Tennessee, and is being developed by the Tennessee Copper Co. GEOLOGY The geology of the district has been fully described in many papers. Probably the most complete description is that of Emmons and Laney.I The rocks of the district are considered to be of Lower Cambrian age and are a part of the Great Smoky formation, consisting mainly of interbedded graywacke and mica schist, in which the ore deposits occur. The ore bodies are included in an area of about 6 sq. miles, 2 miles wide and 3 miles long striking N. 45° E., and may be grouped into three general lode systems. The northeast system, including the East Tennessee, London and Burra Burra ore bodies, and the southeast group, comprising the Polk County, Mary and Calloway deposits, are all characterized by relatively high copper values. The ores of the central system, which includes the Eureka, Boyd, Old Tennessee and Cherokee ore bodies, are low in copper and high in total sulphide content. Boyd mine lies roughly halfway between the Old Tennessee and Eureka ore bodies [ ] and 2500 ft. in the hanging wall of the Burra Burra mine (Fig. 1). Elevation of the surface is about 1725 ft. above sea

Jan 1, 1942

Robert Campbell Gemmell, assistant managing director of the Jackling allied porphyry mining properties in Utah, New Mexico, Arizona and Nevada, died suddenly on Oct. 25, of heart trouble, while traveling from Hurley, N. M., to Los Angeles. To shape justly even an outline of the brilliant career and uniquely charming personality of Mr; Gemmell is well-nigh impossible, and any effort so to do can but demonstrate the inadequacy of language to sound the depths of soul-stirring sentiments. To touch upon his more important work, and afford even a limited conception of his general worth and character, is all I can hope to do.

Jan 1, 1923

Robert Campbell Gemmell, assistant managing director of the Jackling allied porphyry mining properties in Utah, New Mexico, Arizona and Nevada, died suddenly on Oct. 25, of heart trouble, while traveling from Hurley, N. M., to Los Angeles. To shape justly even an outline of the brilliant career and uniquely charming personality of Mr; Gemmell is well-nigh impossible, and any effort so to do can but demonstrate the inadequacy of language to sound the depths of soul-stirring sentiments. To touch upon his more important work, and afford even a limited conception of his general worth and character, is all I can hope to do.

Jan 1, 1923