Search Documents

By AIME AIME

I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability.

Jan 1, 1967

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

By Simon D. Strauss

Production and consumption of nonferrous metals in the United States during 1950 were at peak levels for the postwar period, as is shown in Tables I, II, and III. The trend of production was upward through most of the year. At the year end, with the possible exception of the Tri-State zinc-lead district, the large mining operations in the country were running at capacity. The absence of serious labor interruptions during the year was an important contributing factor in the increased out-put of metals, since in each of the previous postwar years there had been a number of major strikes which affected production adversely.

Jan 2, 1951

By A. J. de Witte

It has been observed that upon invasion of a sand containing oil or gas and connate water by mud filtrate the hydrocarbons are more rapidly flushed by the filtrate than is the connate water.' In time, it appears that the following displacement pattern emerges: oil (or gas) is being swept ahead by connate water which, in turn, is pushed by invading fluid. Eventually the connate water may have "banked up" sufficiently to form a zone of appreciable thickness leading the invading front. In the extreme case, Fig. 1 shows how the situation will develop.' Immediately adjacent to the borehole (radius r) there is a zone, the invaded zone proper, where the connate water has been flushed out completely and which contains only residual oil or gas and mud filtrate. This zone (extending out to a radius ri) grades more or less abruptly into the next (thickness A), which contains only residual hydrocarbon and connate water. Beyond it, again more or less sharply bounded, extends the virgin formation with the original interstitial water saturation Sw. The various saturations are indicated in Fig. 1. The three zones generally will be marked by resistivity contrasts owing to their different fluid contents. As the connate water is usually more saline than the invading fluid, the second zone having a high connate water saturation forms a concentric cylindrical ring or annulus of low resistivity R, around the borehole.',' It will be referred to as the "low zone." Fig. 1 shows schematically the resistivity profile. It is clear that the phenomenon of a low zone could not occur in invaded water sands. The presence of a low zone, therefore, would be a qualitative indication of a hydrocarbon-bearing formation. Granted that the phenomenon is real, if it were pronounced enough to be detected, one might thereby have a means of locating oil or gas in the ground. This is the aim of the "displacement logging" method.' In any case, the presence of a low resistivity zone will affect the reading of electric logs. Using conventional log interpretation techniques, one must be aware of this and, if necessary, correct for it. Whether correction or detection should be the goal will depend primarily on the magnitude of the effect. The type of log which is likely to be affected most is the induction log. The current pattern of an induction log is concentric with the borehole. Any concentric ring of low resistivity, therefore, will tend to become crowded by current lines. This zone of maximum current density will obscure the relative contributions to the current conduction by other portions of a bed making, for instance, the contribution of the virgin formation less significant and thus detracting from the value or the induction log as an R, reading device. The present note is intended to ascertain the maximum possible effect of a low zone in the extreme case portrayed by Fig. 1 on three commercially available types of induction logs, sc., 5 FF 27, 5 FF 40 and 3 F 60. Type 5 FF 27 or 5 PF 40 is currently run in conjunction with a 16 in. normal and SP log. This combination is gradually replacing the regular electric survey (two normals and one lateral) as a standard log in many areas. On the basis of the scheme of Fig. 1 (sharp boundaries between successive zones), the thickness of the low zone may be computed for various amounts of infiltration measured by the ratio of invaded zone diameter to hole diameter D,/d. Referring to Fig. 1, we can set up a material balance for the water displaced from the invaded zone proper and the water present in the low zone. The volume of connate water displaced from invaded zone upon flushing by mud filtrate is: V1 = e p (r2 - r2) ? Sw . where c = bed thickness ? = porosity Su, = original connate water satu-ration. The volume of water finally accu-mulated in the low zone is: Vz = e p [(r1 -?)2 - r2 4] ? Sw . where SW1 = 1 — Sor = "water" saturation in the invaded and low zones both. The volume of water originally present in the low zone is:

Jan 1, 1958

By L. R. Plitt, E. O. Lilge

Tests carried out with both kaolin and silica slurries show that flocculants of the polyacrylamide type can be used to improve the thickening performance of hydrocyclones. This thickening improvement demonstrates that contrary to previously held theories, flocs can be formed which are capable of resisting the shear forces in a hydrocyclone. For the 1.25-in.-diam cyclone used, optimum thickening occurs when the flocculant solution is injected into the slurry stream at or near the feed inlet. Hydrocyclones offer many distinct advantages over gravity thickeners. These advantages include simplicity, low initial and operating costs, small space requirements, and flexibility of operation. In spite of these advantages hydrocyclones have not been widely used as thickeners. The main reason for their lack of application is that hydrocyclones are unable to efficiently remove semicolloidal particles (less than 5 microns) from the suspending solution. In gravity thickeners, the fine particles can be induced to form particle aggregates, or flocs, which have the settling characteristics of large particles. In the hydrocyclone, however, it was always assumed that the existence of shear would prevent the formation of flocs.1-3 Thus, if no floc structure is retained, the thickening hydrocyclone must be designed so that its separation size is below the size of the smallest particle to be recovered. To obtain a very small separation size requires the formation of very high centrifugal forces, which necessitates the use of small-diameter cyclones. Small hydrocyclones have, in turn, very low throughput capacities which render them impractical for many industrial thickening applications. Thus, if the effects of flocculation cannot be utilized, the usefulness of hydrocyclones as thickeners remains limited to pulps which contain no very fine particles. It is well established that most substances acquire a surface electric charge when brought into contact with an aqueous medium. The repulsive interactions between similarly charged particles act to prevent flocculation. One method of flocculating a dispersion is to neutralize the repulsive surface charges by the addition of an electrolyte. The reduction of the electrostatic surface charge (Zeta potential) then permits the universal van der Waals attractive forces to operate between the atoms of the various particles and form particle aggregates. The lime additions used by thickener operators promotes flocculation by this mechanism. A second method of flocculating a dispersion is by the addition of long-chain macromolecules. In this case flocculation is brought about by a bridging mechanism in which the molecules are adsorbed with part of their length on two or more particles, thus forming a molecular bridge between the particles.4,5 The molecules also form bridges between themselves when a single particle is bonded to several polymer molecules. The type of bonding between the flocculant molecule and the particle may be hydrogen bonding, chemical bonding, or electrolytic attraction.6 The flour and glue which are used as thickener additives are believed to promote flocculation in this manner. In the past decade synthetic long-chain polymers with extremely high flocculating capabilities have been developed. The flocs formed by these new polymeric flocculants are larger and more shear-resistant than those formed by the presence of electrolytes.7 The advent of these flocculants raises the question: Are the flocs formed by these synthetic polymers stable enough to resist the liquid shearing forces in a hydrocyclone? The investigations reported in this paper were carried out in order to provide some answers to this question. EXPERIMENTAL WORK For the bulk of the test work a 5% slurry of commercially available kaolin with an average particle size of 5 microns was used. An initial evaluation of the available flocculants was carried out to determine which flocculant formed the most shear-resistant flocs. A combination of the techniques used by Healy7 and Booth8 was used for this purpose. This initial study revealed that the neutral high-molecular weight polyacrylamides produced the most shear-resistant flocs. One of these flocculants, Separan MGL*, was selected and then used for all the hydrocyclone tests. The flocculant was dissolved in water and added to the hydrocyclone as a dilute solution.

Jan 1, 1968

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By J. C. Konopka, S. A. G. Poppen, E. K. Roesner

Many shafts have experienced stability problems during shaft sinking because the designer failed to fully appreciate the conditions he would encounter. Some shafts have failed during construction because the ground supports provided to compensate for the expected conditions were inadequate despite the most careful investigations and analyses. To design a ground support which is ultimately safe to achieve stability during shaft sinking would be too costly and impractical and, therefore, many shafts would simply not be constructed. The design of a ground support for shaft sinking based on an intimate understanding of the expected ground behaviour and stress development during excavation combines the art of mining with the science of geotechnical engineering. Where no historical design data is available, the designer of the ground support must: 1. classify the rocks and soils and assess their behavioural characteristics; 2. calculate the primary and secondary stresses; 3. design and/or select a ground support system which will ensure stability of the excavation during shaft sinking.

Jan 1, 1983

By J. W. Halley

THE effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. PUBLISHED WORK A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimm1 found no change in Olsen ductility, Rockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.15 per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength 0f from 100 t0 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0.50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. EXPERIMENTAL WORK Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1942

By P. F. Richardson, J. L. Perisho, W. J. Roe

Handling and transport of coal during the winter months can be a severe problem. The inability to unload frozen coal from rail cars produces serious economic and logistic problems due to transportation delays, rail car shortages, and demurrage on the rail cars. One method of dealing with the problem of unloading frozen coal has been to spray freeze conditioning agents onto the coal before it is loaded into rail cars. Both water soluble and oil based formulations have been used as freeze conditioning agents. The water soluble treatments generally contain a polyhydroxy alcohol, such as ethylene glycol, or salts of alkaline earth metals, such as magnesium chloride and calcium chloride, as freeze point depressants. The oil based treatments consist principally of hydrocarbons, such as No. 2 oil or diesel fuel. The authors' tests have shown significant differences in the effectiveness of these freeze conditioning agents, depending on the particular coal substrate being treated. These differences correlate with the coal porosity and inherent moisture of the substrate. In general, the greater the porosity of the coal, the smaller the effect of the freeze conditioning agents. Coal porosity has a greater impact on water soluble freeze conditioning agents than oil based products. The authors investigated the pore structure of a variety of coals using mercury intrusion. Findings were related to the effectiveness of different freeze conditioning agents as measured by unconfined compression strength tests. In general, coals with a large number of very small pores (between 0.05 µm and 0.03 µm) do not respond as well to freeze conditioning chemicals.

Jan 1, 1986

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg's stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg's phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

THE strike and dip of bedded formations is readily determined by trigonometry if some marker horizon is intercepted by three holes. If no marker can be identified and if orientation of the cores is unknown, as is the usual case in diamond drilling, the determination still can be made readily by the use of a stereonet if the bearing, inclination, and angle the bedding makes with the core axis is known for each of the three holes. Such determination, valid only if the bedding orientation is fairly uniform within the area drilled, is considered simpler, faster, and more effective than any solution previously published. Method: The steps of this procedure are as follows: 1) Mark north and south poles on tracing paper placed over stereonet.* 2) Plot the three diamond drillholes by drawing a line from the center of the net in the direction of the bearings of the holes. Then rotate the paper until each line, in turn, lies along the equatorial diameter of the net; the end of each line is determined by the inclination of the hole measured in degrees from the periphery toward the center of the net along the equatorial diameter. Fig. 1 illustrates a vertical hole and a hole inclined at —23" due east. 3) With the projection of one diamond drillhole along the equatorial diameter, measure from the end of the hole, to the east and then to the west, a dis- tance in degrees equal to the core axis-bedding plane angle. Find two more points by measuring the same number of degrees north then south along the great circle from the end of the drillhole. Draw a circle, the center somewhere along the direction of the projection of the drillhole, to connect these four points. Draw circles for the other two diamond drillholes in the same manner. See Fig. 1 for two circles representing core axis-bedding plane angles of 35" and 23" and Fig. 2 for these plus a third circle representing a core axis-bedding angle of 42" in a hole bearing S 50 W inclined at —52". 4) Rotate the tracing paper until one great circle on the stereonet is found which is tangent to all three of the circles or parts of circles derived in the previous step. Trace this great circle on the paper and join its ends with a straight line passing through the center of the net. The bearing of this line is the strike of the bedding. In Fig. 2 the bedding strikes N 77 E. 5) Rotate the paper until the strike is along the polar diameter of the net. The dip of the bedding is determined by measuring along the equatorial diameter the distance in degrees from the periphery of the net to the great circle derived in step 4. The dip of plane illustrated in Fig. 2 is 55" to the N 13 W. Fig. 3 indicates the solution for three holes whose bearings and inclinations are N 20 W and —43o, due E and —30°, S 30 W and 23" with core axis-bedding angles of 30°, 50°, and 43" respectively. The bedding (stippled area) strikes N 44 W and dips 70" to the southwest.

Jan 1, 1956

Jan 1, 1929

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

By R. L. Smith, I. G. Greenfield

The binary system Ga-Sb has been investigated by thermal, X-ray, and metallo-graphic methods. 'The intermetallic compound GaSb melts at 705.9OC and forms a eutectic with antimony at 11.8 atomic pct Ga. This eutectic melts at 589.8OC. A eutectic appears to be formed at 29.8°C but is too close to the composition of pure gallium to be detected. IN the course of an investigation of the semiconducting properties of the intermetallic compound, GaSb, the phase equilibrium between gallium and antimony has been investigated. Recently, the phase diagram of similar systems, such as In-Sb,' In-AS,' and Bi-As3 have been determined. These diagrams have the same general appearance in that an intermetallic compound is formed at 50 atomic pct and a eutectic is formed on both sides of the intermetallic compound. Jenny,& who has been investigating the semiconducting properties of intermetallic compounds, has concluded from thermal data of several alloys that the phase diagram of the Ga-Sb system resembles those mentioned previously. This paper represents a more detailed study of the Ga-Sb equilibrium. Experimental Procedure The gallium that was used to prepare the alloys was obtained from A. D. Mackay Inc. and the Aluminum Co. of America; the latter reported the purity as 99.95 pct. The antimony was obtained from Bradley Mining Corp. who specified a purity of 99.997 pct. Since the intermetallic compound of GaSb was prepared primarily to be used for further studies of the semiconducting properties, additional purification by a standard zone-melting technique under an atmosphere of hydrogen was performed. Hall-effect measurements on this material indicated an impurity content of less than 3 ppm.5 The antimony also was purified by zone melting and used in conjunction with the compound GaSb to make the necessary alloys for the determinations of the antimony-rich side of the phase diagram. The antimony-rich alloys were chill cast in Vycor tubes which were evacuated to a pressure of less than one micron. Since these alloys expand on freezing, precautions were taken to prevent oxidation of the ingot in the event the tube fractured. To insure homogeneity, the brittle alloys were ground and then placed in the furnace for the thermal-arrest determinations. Since the cost of gallium is high, the experimental procedure was complicated somewhat because of the necessarily limited sizes of the melts. In order to economize, the gallium-rich side of the diagram was determined by using a 35 g ingot of pure gallium initially and adding increasing amounts of antimony in order to obtain additional alloys. The furnace used in the determination of the cooling curves is illustrated in Fig. 1. A 2¼ in. quartz tube, sealed at one end, was fitted with a brass flange which was attached with DeKhotinsky cement. The brass collar was water cooled to prevent the cement from softening. An "0" ring was used to provide a seal between the brass collar and the furnace cover. Nichrome ribbon was wound around a 2 ½ in. asbestos-covered copper core which was used to reduce the thermal gradient in the furnace. The insulation consisted of alternate layers of asbestos and aluminum foil surrounded by sil-o-cel refractory and

Jan 1, 1956

By AIME AIME

OPPORTUNITY may not be knocking but it, at least, is waiting for you, your family and your friends in that amazing republic south of the Rio Grande. For the first time we are able to publish the official itinerary for the forth-coming Mexico City meeting of 1936. As shown on Page 351, the deluxe special train leaves St. Louis on Thursday. Nov. 5 at 5:30 p.m., returning to St. Louis on Nov. 18 at 8:15 a. m. The schedule provides seven days and six nights in Mexico City with numerous excursions to nearby towns and resorts. The oldest surviving city in' North America is Mexico City, dating back at least to the twelfth century. It was the Aztec capital when Cortez arrived in 1519. The famous cathedral still standing was built on a foundation of sculptured Indian images and the remains of a great Aztec temple. Today it is a city of romance.

Jan 1, 1936

Single orders 2.5 c. Pamphlets 10. c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlet, of the same or different titles. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long as the supply, lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets that have been published by the Institute. Any other paper published by the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare.

Jan 5, 1917

By John Freeman

THIS paper relates entirely to the casting of brass under fluid pressure in steel dies. Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years. The successful development of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitable die-casting machines. The melting point of copper is 1084° C. (1983° F.) and of a high brass about 900° C. (1652° F.), as compared to 327.5° C. (621.5° F.) for lead, 419.4° C. (786.7° F.) for zinc and 658.7° C. (1217.7° F.) for aluminum, temperatures that are indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals.

Jan 1, 1935

By A. Hellawell

Specitlrens of the Al-Ge eutectic alloy have been frozen unidivectionally at rates between 2.5 x 10-6 and 2.5 x 10-4 cm per sec and the structure examined by optical and X-ray methods. There is no epitaxial relationship between phases, the aluminum having random orientation and the germanium a preferred (011) fiber textuve. Lamellar colonies which are BINARY eutectic alloys occur between either silicon or germanium with the metals aluminum or silver. common in this alloy are constructed from axial and nonaxial (111) plates of germanium which are related by a variety of twin configurations. Irregular or globular regions of the microstructure are composed of continuous single crystals of each phase, the germanium being heavily twinned. There is limited solid solubility in these systems, and the eutectic phases all involve diamond cubic with fcc crystal structures. In the microstructures of these eutectic mixtures the silicon and germanium crystals exhibit an almost infinite variety of shapes which are notably sensitive to

Jan 1, 1968

By T. Sterry Hunt

BUT little was known of the coals of Southeastern Ohio until the present survey of the State under Dr. Newberry began its work. The results of the geological investigations of Prof. E. B. Andrews in this region, and of the chemical investigations of Prof. T. G. Wormley, both of which appear in the reports of the survey for 1869 and 1874, and more recent special reports by the former, together with some data for which I am indebted to the kindness of Dr. Newberry, and my own limited observations, have served me for the preparation of the following notice of the coals lying on the western border of the great Appalachian coal-basin in the region drained by the Hocking River and its tributaries, and belonging to the Lower Coal-Measures. Some uncertainty exists as to the place in the succession of the lower coals to be assigned to the seams known and mined in the Hocking Valley. It is the opinion of Prof. Andrews that the inequalities of the original surface were such that we cannot identify in that region the lowest coals known in Northwestern Pennsylvania and the contiguous parts of Ohio, but that we must rather count from above downwards. These conclusions Dr. Newberry is not prepared to accept, and further researches will be necessary before certainty can be attained in this matter. Meanwhile it seems, from a study of its relations to the Pomeroy or Pittsburgh seam, that what is known as the great vein of the Hocking Valley, occupies the horizon of the Upper Freeport coal, E of the Pennsylvania survey, or No. 6 in Dr. Newberry's enumeration, counting from the base. This seam, in the region in question. assumes certain characteristics which, taken in connection with its geographical position, give it a great importance among the coals of the State. The area to be noticed includes the whole or parts of several townships in Perry, Hocking, Vinton, and Athens Counties, lying near the margin of the basin over which the vein in question assumes the character of a dry-burning or splint coal, and has a thickness varying from six to ten and even twelve feet. Its precise limit southward cannot at present be clearly defined, but it has been found as far south as the line of the Marietta and Cincinnati Railroad, with a thickness of six feet, and is mined at various points along the valley of the Hocking River, near Nelsonville, where it attains six or seven feet. To the northward, along the tributaries of this river, Sunday and Monday

Jan 1, 1874