Search Documents

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By A. Lubinski, J. L. Logan, W. S. Althouse

A4ost gas twells and flowing oil wells are completed and treated through a string of tubing and a packer. Changes in temperature and in pressure inside or outside the tubing will: (I) if free motion of the tubing inside the packer is permitted, increase or decrease the length of the rubing; or (2) if free motion is prevented, induce forces in the tubing and on the packer. If pressure inside the tubing is greater than outside, the tubing may buckle helically even in the presence of a packer-to-tubing tension. The tubing will always buckle, and much more severely, if free motion is permitted. The buckling may be prevented by pulling the tubing in sufficient tension. The prediction of these forces and tubing movement has here to fore been based upon calculations that did not inciude helical buckling. This paper preseitts means with which these length or force changes can be calculated while taking into account the effect of helical buckling. To avoid damaging formations, failure of remedial operations, or damage to the tubing or packer, application is made to practical problems involving calculations of the required length of seals, amount of sluckoff or tension, and prevention of permanent corkscrewing. INTRODUCTION Leakage of a packer may result in costly failures of such operations as squeeze cementing, hydraulic fracturing, etc. To avoid such failures, the authors are often asked questions pertaining to the length of necessary seals, the amount of necessary slackoff, etc. Published work' does not take into account helical buckling of tubing. Investigation of helical buckling was prompted by the fact that allowance must be made for this phenomenon in order to provide relevant answers. In the past, theoretical work on helical buckling was confined to conditions for which such buckling does not The mathematical treatment of behavior in a buckled condition, given in the Appendix, is novel. Assumptions upon which this investigation is based are listed and discussed in a special section. The following are a few of the many kinds of problems which may be solved with this paper. 1. Consider a packer in which tubing may move. Such movement will occur after pressures and temperature are changed. The paper provides means for: (a) calculating the amount of such movement and, therefore. the required length of seals; and (b) calculating the necessary amount of initial slackoff, for which there is no danger of unsealing the packer, if the length of seals is given. Such calculations, as well as those which follow, tully take into account the fact that part of the movement ib due to elastic helical buckling of the lower part of the string. This buckling may occur even in tubing under tension. Insufficient initial slackoff for a given length of seals, or insufficient length of seals for a given slackoff, may result in costly failures. A field case of such a failure will be given further in this paper. 2. In the case in which tubing cannot move in the packer, changes of pressure and temperature result in tubing-to-packer forces and forces in the tubing above the packer, both of which may be calculated. This knowledge is important because, if these forces are too large, the) could damage the packer or the tubing. 3. For wells in which wireline tools are to be run through the tubing, the paper provides means to keep the tubing from buckling, thereby permitting free passage of tools. 4. In deep wells, mainly in the presence of large casing, tubing may become "corkscrewed", i.e., take a permanent helical set. A field case is described further in the text. Using this paper, one may calculate in advance conditions under which permanent corkscrewing would occur, and then take preventive steps. HELICAL BUCKLING Consider a string of tubing, freely suspended in the absence of any fluid inside casing, as shown in Fig. I(a). Now consider an upward force F applied at the lower end of this tubing. This force compresses the string; and if the compression is large enough (which is always the case in actual problems), the lower portion of the string will buckle into a helix, as shown in Fig. 1 (b). The lower end of the tubing is subjected to a compression F. This compression decreases with the distance from the bottom and becomes nil (neither compression nor ten-

By Michael P. Robinson

It has been suggested that streaming potentials are not nomlally logged because the streaming potentials known to be generated across mud filter cakes are substantially cancelled by streaming potentials generated in contiguous shale beds. Laboratory measuments of streaming poterztials acrons hand specirnens of shale have been adduced as evidence to support the suggestion. The experiments show that streanzing potential depends on the resistivity of the equilibrating solution and on pressure drop. Meizsurenlents were made perpendicular to the bedding planes of the shales. The mechanism of streaming potential generation in shale which the suggested cancellation theory iniplies has been critically examined. Conclusions reached are tested by comparing self potentials logged before and immediately after changing the resistil~ity (but not the weight) of mud in a borehole. The resultant SP change is found to equal the theoretical electrochetnical potential change, i.e., cancellation of .strearning potential is independent of mud resistivity. Since streaming po/entials generateal across mud filter cakes depend critically upon mud reistivity, shale .strearlling potential in situ must he equally sensitive. Using plausible values for the pemleahility, porosiy arzd compressibility of shale, the van Ererdingerl-Hurst approach shows that the pressure drop between horehole pressure and formation pressure in a radially honzogeneous shale is unlikely to coincide with the zone of filtrate invasion. If, perchance. this coincidence occurs with one mud a chatzge 10 a second must result in non-coincidence, i.e., a .YP logged in the second mud should show a streaming potenlial. The dilernrna may he overcome by postrrlating: (I) perrneabilities of shale7 parallel to their beddine planes greatly exceed their cross-bedding permeabilities; (2) a resistivity-sensitive mud cake of low permeability forms either on the face of, or probnhly in the lanlinations of, many shales. These postulates are examined with reference to the pres.sure and SP histories of the McClosky and Aux Vases zones in the Illinois Basin and some srcpport for them found. It is concluded that a definitive solultion to the streaming potential problem does not exist. INTRODUCTION Recently Gondouin and Scala' published a contribution to the streaming potential problem which is notable particularly for the elegance of its experimental techniques. The conclusions drawn by Gondouin and Scala from their studies amplified those previously suggested by Schehck'. In essence they suggested that the streaming potentials known to develop across mud filter cakes" are not normally observed on SP logs because they are largely cancelled by streaming potentials generated in adjacent shales. This suggestion appears so reasonable that many workers in the logging field will be prone to accept it. We incline strongly to the view that the suggestion is basically correct. Nevertheless, it is important to realize that the cancellation hypothesis in the form put forward by Gondouin and Scala does not appear to meet all the known experimental facts. It is the principal intention of this note to call attention to what appears to be a flaw in the relevancy of the experimental evidence adduced by Gondouin and Scala and to suggest an alternative hypothesis to remove it. The consequences of the new hypothesis are compared with field data which, we believe, are unique. A second but not less important purpose of this note is to emphasize that even the new hypothesis does not fully explain all field observations. Hence we conclude that further study of the streaming potential problem is required before it can be said that a definitive solution to it has been attained. The bare experimental bones of laboratory data on streaming potentials appear to be as follows. 1. A streaming potential is developed across a mud filter cake. This streaming potential is virtually independent of cake thickness but depends on the mud resistivity. The relationship is of the form, 2. A streaming potential is developed across a shale. This potential is independent of shale thickness but depends on the resistivity of the permeating solution if the shale has been first equilibrated in this solution. The relationship is of the form, The relationship in (1) was determined first by Wyllie3, confirmed by Gondouin and Scala and qualita-

By H. B. C. Nitze

A description of some of the magnetic ore-deposits in this region should be of interest to the mining and metallurgical public, inasmuch as very little has been said or written concerning them. I refer to the magnetite deposits of Franklin and Henry counties, Va., and of Stokes county, N. C. These deposits remained comparatively unexplored until recently, when the construction of the Roanoke & Southern R. R. through this territory has called attention to them, by furnishing the means of transportation for the ores. It is true that the ores have long been known, at least locally, and were smelted in catalan forges and old-fashioned, cold-blast charcoal-furnaces long before and during the late war. At the present time, however, the old workings are caved in, filled up and over-grown to such an extent that, as a rule, but little can be learned from them. No prospecting of any consequence has been done, and as my time was too limited and the territory to be examined too extensive to permit additional openings of a more satisfactory nature to be made, the incormpleteness of some of the data I have to offer (notably, those referring to the absolute width of the veins) will be pardoned. It will hardly be necessary to say that this ore-bearing formation belongs to the Archaean, or Eozoic age, the usually occurring rocks being schist, shale, gneiss, granite, sandstone and quartzite. The stratigraphy is, as a rule, quite regular (excepting in the Danbury section, Stokes county, N. C.), the general strike being northeast and southwest, and the dip nearly vertical. The country is gently roll-

Jan 1, 1892

By Thomas H. Leggett

In speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining practice, since this has been already well described both in the Transactions' and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a whole, marking its general development and the lines of its future progress. In a paper entitled Deep-Level Shafts on the Witwaters-rand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,' presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (p. 975): '" In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discuesed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy wae vitally necessary for both

Jan 1, 1909

By H. C. Spaulding

The rapid increase, during the last few years, in the number and magnitude of applications of electric power-transmission to commer cial uses in this country, has been due principally to three causes: first, the ability and enterprise of those who have been identified with the progress of electrical industries, since electric illumination became an economic fact instead of a laboratory-experiment: sec ondly, the readiness of the American people to adopt new and ad vanced methods as soon as their superiority has been fairly demon strated; and thirdly, tile economy and flexibility of the apparatus employed, when properly designed and constructed, and installed under suitable conditions. Basing our judgment on the world's advance in scientific devel opments during the past century, we may reasonably conclude that in no other country would the pioneeis of electrical invention, whose names have now become household words, have received the prompt and plentiful financial support which has enabled them to inaugurate undertakings of exceptional magnitude, even in this era of tremendous monetary organizations. And, on the other hand, we have seen, in the numerous financial and engineering failures inseparable from such rapid development, the natural results of a too implicit faith in electrical omnipotence. It is not to be wondered at that conservative engineers have been slow to adopt this new and mighty agent in the solution of exten sive problems, and under circumstances where a single failure means not only a greater or less financial sacrifice, but the loss, in a greater or less degree, of professional reputation. Be mechanical engineer, while recognizing the fact that thousands of horse-power are to-day transmitted by electrical means, from sunning the lathe in a dentist's office to the operation of a fifty-ton travelling crane; from passing a cooling draught of air through a

Jan 1, 1891

By Robert I. Jaffee, Walter L. Finlay

IN the broad survey of the nonferrous' metallic elements contained in this book, the reader may well be impressed by the wide range of property combinations offered by the many metals and alloys the metallurgist has prepared since before Kubla Khan. The diversity is great and the overlap is considerable. It is particularly surprising, then, to find the latest structural metal new- comer designated by such extravagant terms as "Cinderella Metal," "Wonder Metal," "Miracle Metal," "The Metal of Tomorrow," "Dream Metal or Nightmare?" and "The Middleweight Champion of the Structural Metals." Of these and others, the most appropriate designation for the metal involved, titanium, appears to be that of The Middleweight Champion. Its intermediate density of 4.5 and elastic modulus of 16 million is a unique combination between the lower density and modulus of magnesium and aluminum and the higher density and modulus of copper, nickel, and iron. It is light, strong, ductile, and corrosion resistant. A chemical neighbor in group IV of the Periodic Table, zirconium, is similar to titanium in many respects but is appreciably denser, 6.5 instead of 4.5, less stiff and relatively much less abundant. On the other hand, the resistance of zirconium to acids and alkalies is better than that of titanium. Also, compensating for its higher density, lower stiffness, and somewhat lower strength level compared with titanium, zirconium has much better permeability to slow neutrons and is much more suitable as a material of construction for nuclear reactors.

Jan 1, 1953

By T. Egleston

The importance of condensing the gases which escape from furnaces so as to save both the fine particles of ore carried off mechanically and those which are volatilized, has for a long time occupied the serious attention of metallurgists in all parts of the world. It was my good fortune during the last summer to visit the lead and silver works at Ems, near Coblentz on the Rhine, and through the politeness of Mr. Freudenberg, general director of the works, to study in detail their methods of condensation, and to receive from him the important results which have been obtained through a series of experiments lasting over a number of years. I have thought, that these results would be of great interest to the members of the Institute and to other metallurgists in the United States, and I have, therefore, with the assistance of Mr. Freudenberg, prepared a careful, detailed description of the construction of the flues, as well as an account of the various experiments which have been made with them, and the conclusions arrived at as the result of these experiments. It may be said, in general, that the reason why so little attention has been paid in the metallurgical works of the United States to the collection of flue-dust, is that we are not generally aware of the large amount of material carried off by the gases. This is owing partly to the fact that little or no attention is paid to the subject, and also to the fact that the assays, which are almost invariably made in the dry way, show a result so much below the real contents

Jan 1, 1883

By Bob J. Rawicki

TYPES OF WET DUST COLLECTORS Basically, there are two types of wettype dust collectors. One is mechanical, incorporating pumps, motors, fans, sprays, filters, or flooded beds. These come in many forms, but their operating principle is basically the same. The screen or flooded bed is wetted by a series of sprays. Polluted air is drawn in through a fan; here the dust particles impinge on the screen and are flushed off into a settlement tank. The air then passes through spray eliminators to the atmosphere. A great deal of time and money has been spent developing this type of collector. In laboratory tests where clean water at constant pressure, air at constant volume, and dust at low but constant mass to volume were applied, these collectors gave high percentage dust collection efficiencies. Theoretically and technically, they are very good. In practice, however, under rugged mining conditions where there are no constants, and dust load, particle size, water pressure, and volume of air vary with time, their efficiency varies dramatically. Some of the most common problems are: 1. clogging of screens 2. blocking of nozzles 3. replacement. of damaged pump stators Any of the above result in loss of air flow and dust collection efficiency. Generally, there are so many mechanical moving parts, something is always breaking down. This type of collector is very expensive in parts and labor to maintain. The second type of dust collector, which I personally developed, with the help of the British National Coal Board of Great Britain, has none of the above mentioned problems and it works on a completely different principle. My collector, the Mark III Precipitaire Wet-Type Dust Collector, (an improved version of previously successful models) has no internal moving parts, no flooded beds, screens, spray nozzles, etc. It is highly efficient - 99.8% efficiency on total collected dust and 97% on respirable dust. The pressure drop through the collector is constant, hence, air flow remains constant. There is no maintenance expenditure, be it labor or parts. The only maintenance that there is, is desludging. This, of course, varies with the dust load. With a low dust load, desludqinq may only be required every 4 weeks, but this is a very simple operation that can be handled by unskilled men and it takes only a very short time. My collector is powered by a ventilation fan that is placed on the clean air side for a longer fan and motor life. Dust is extracted solely by water action. The collector's operating principle is: Dust laden air is drawn in along ducting into a tapered scrubber section, shaped to create a self-induced curtain of water. This action washes the dust particles from the air and the collected dust settles into the bottom of the tank. Cleaned air is then exhausted via a series of spray eliminators where it is completely dried and on into the atmosphere. These collectors have been sold in Great Britain, to the National Coal Board, and throughout Europe. They have been working very well for many years now. GENERAL APPLICATIONS Dust is very dangerous; silicosis and black lung kill and disable many workers each year. Many of the mine explosions can be attributed to coal dust. By the use and application of dust collectors, these deaths and disasters can be avoided. There really is no excuse. However good and efficient a dust collector may be, it's positioning and installation arrangement is critical. The collector may remove 99% of dust supplied to it, but it takes the skill and experience of a dust control engineer to design and fit ducting, hoods, etc. to remove polluted air at source and deliver it to the collector. In some cases this is very simple; in the case of longwall machines, it is very difficult. In general, dust collectors should be used to collect dust at every point of dust generation. I have noted a great reliance on dilution as a means of dust control. I personally think this is a dangerous and unreliable method. As mines become deeper and the use of larger and more productive equipment becomes more common, reliance on dilution will be impossible and dust collectors will be essential.

Jan 1, 1982

By Harold Cook

Discussion of the paper of HAROLD EARLE COOK, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 375 to 400. ALBERT SAUVEUR, Cambridge, Mass.-I think we must all agree with Lieutenant-Commander Cook when he says that there is a great deal of room for improvement in the annealing of steel castings and that better results would be attained if the annealing were conducted in closer agreement with scientific requirements. Whether even a carefully annealed steel casting can ever be made the equal of a steel forging of good quality is still a debatable question. Nevertheless, we all realize that very greatly improved results can be attained by careful annealing. Lieutenant-Commander Cook refers to some requirements calling for annealing steel castings above the Ac1 point. He is undoubtedly right where he says that this should be the Ac3 point. Take, for example, a steel casting containing, say, 0.35 per cent. of carbon, having a very coarse structure made up of coarsely crystalline ferrite. If this is heated just above the Ac1 point the ferrite remains, of course, just as it was before, while the pearlite is converted into a solid solution, austenite. Upon cooling, all this austenite is again converted into pearlite, or sorbite, while the coarse structure of the ferrite remains unchanged and the annealing has accomplished very little. It is therefore surprising that the requirement of annealing above the Ac1 point should appear, in these specifications.

Jan 5, 1916

By Harry Seltz

SEVERAL investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeser1 has made measurements of "average heat capacities" of iron carbide between 1026° and 85° K., using a water calorimeter. His computed true specific heat at 78.1° K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0° K. The cementite used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes" has measured the specific heat of iron carbide, from 102° to 323° K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100° K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3C, S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley' has reviewed these measurements and calculations, and selects those of Roth4 and Naeser5 as worthy of most consideration. Roth has given ?H = 5400 cal. ± 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (ß) he finds OH = 5600 cal. Kelley accepts the rounded figure ?H = 5500 as the heat of formation at 298.1° K., but this value is quite uncertain.

Jan 1, 1939

By Y. C. Liu, G. A. Alers

Using X-ray pole-figure information and the single-crystal elastic constants, the angular variation of an elastic modulus in a polycrystal can be calculated and compared to measured clalues. This procedure has been used in the past to provide supporting ecidence for a particular choice of ideal orientations in the description o the X-ray pole figure. Since it is well-known that the absolute value oj an elastic modlus oj a poly crystal cannot be acczrralely calculated from the single-crystal elastic constants, there exists a serious question about the reliability oj this modulus method in the study of textures. This paper deriz-es sez3eral simple fornzulae for the ntzgular lariatiion of Young's modulus in the plane o a rolled sheet sing the same ssuinptions which lead to the lack oj detinztion of the absolute c'alre OJ the elastic ,nodulus. The vesults show that, although the absolute isallre oj Young's modulus depends strongly on the assumptions made, the shape of the modulus vs angle curve is not very sensitive to the assumptions and thus can be used reliably in texture studies. Exatzples oj' using this criteriotz are illustrated in the text. NeARLY all poly crystalline materials have some preferred orientation in the arrangement of their grains and hence exhibit anisotropy in their properties. This preferred orientation is usually measured and studied by X-rays which yield detailed information on the statistical distribution of grain orientations in the form of pole figures. The usefulness of these pole figures in theories of texture formation and in predictions of properties has come to depend almost entirely on the characterization of the pole figure by one or more ideal orientations. Unfortunately, this characterization is not unique and different authors often present different ideal orientations to characterize a given pole figure. In order to distinguish between these different choices of ideal orientations, it is necessary to go beyond X-rays and consider other physical properties which reflect the texture' simply because any choice of ideal orientations must predict correctly the observed anisotropy in all physical properties. The most common example of this procedure has made use of the angular variation of Young's modulus with respect to the rolling direction in the plane of a rolled sheet.3 4 Here the anisotropy can be measured easily and it can also be calculated from the single-crystal elastic constants and the chosen ideal orientation. Unfortunately the methods used to calculate this anisotropy were chosen for their simplicity rather than for their mathematical rigor so that there exists a serious question as to the validity of conclusions reached by this modulus method. It is well-known5 that the absolute value of the Young's modulus of a polycrystalline aggregate cannot be calculated very accurately because different mathematical averages over the grains yield different results. It is one purpose of this paper to examine the effect of different averaging procedures on the calculated anisotropy of Young's modulus in the rolling plane of rolled sheets in order to see if this property can be used reliably in texture studies. This particular modulus and type of material were chosen because the modulus is easily measured and rolled sheet is technologically important. The results show that, although different averages yield different absolute values for Young's modulus, the shape of the modulus vs angle curve is not very sensitive to the averaging procedure and thus can be used as a criterion to check the various ideal orientations used to characterize the X-ray pole figure. Examples of this checking procedure are given in the final section. Another purpose of this paper is to examine the possibility of using the anisotropy of Young's modulus as an indicator of texture without reference to pole figures or ideal orientations. Such a use would require that different textures yield quite different shapes for the modulus vs angle curve so that the distinction between textures would be quite clear. The experimental results presented in the final section indicate that there is easily enough variation in shapes to allow modulus measurements to be useful texture indicators, par-

Jan 1, 1967

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

By L.L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. INTRODUCTION Buchans is 5 miles north of Red Indian Lake, in Central Newfound- land, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller- town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Ch, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By Francis B. Foley

In examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found a piece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstattian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: Carbon Nickel Chromium Per Cent. Per Cent. PeR Cent. Metal from skin........................... 0.34 1.26 0.63 Widmannstattian zone.................... 0.21 1.18 0.63 Metal from center......................... 0.34 1.32 0.67 Such a condition might result from decarburization followed by recarburization of the skin. This section came from one of the branch runners to the bottom of the mold, not from the main runner, and it is difficult to conceive of decarburization occurring in this portion of a runner. If the metal were stripped while quite hot, some oxidation would take place but the recarburization is unaccounted for. It could not occur by segregation after solidification—the tendency then is for diffusion and homogeneity. The following seems to fit the conditions and is offered as an explanation. The outside layer of normal structure 0.065 in. (1.6 mm.) thick was chilled on the walls of the runner brick when the molten metal first entered the runner. As the molten metal flows by, the outside of the stream

Jan 1, 1920

By JAMES GAYLE

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1905.) IT is to be regretted that the data respecting the use of dry-air blast, which was presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should. have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. In the discussion of the paper it would appear from the conclusions of some participating therein, that they have been placed at some disadvantage in considering the economies obtained through the use of dry-air blast, by reason of the data covering such a short period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs, and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natural air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jul 1, 1905