Search Documents

By Alexander Bowie

Of the following problems, some have been suggested by recent articles in technical journals, which have led me to believe that the mathematical discussion here submitted may be of use to mining engineers. Problem I. To Find the Grade or Angle of Inclination upon which the Power Required to Move a Loaded Car Down-hill Will Haul an Empty One Up-hill. Let a be the desired angle of inclination; C, the coefficient of' friction; W and w, the weight in pounds of the loaded and of the empty car, respectively.

Jan 1, 1902

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th'rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling' in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

Briefly, an open stope is one in which the ore is taken out and no filling is put in; the only support for the walls may be posts or pillars of ore. Such a method is limited to orebodies with strong walls and ore strong enough to stand unsupported over the back of the stope. Details vary and depend on the dip of the vein, mode of breaking ground, method of handling broken ore, and so forth. The examples given are the Beat-son, Birmingham district, Mineville district, and Cornucopia.

Jan 1, 1925

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By W. E. Field

In the Coast Mountains approximately 110 miles north of Vancouver, the gold mine of Bralorne- Pioneer Mines Ltd. lies at an elevation of 3500 ft. The deepest or 41 level in the mine is at an elevation of 1400 ft below sea level, and the rock temperature on this level is 122.5°F. The thermal gradient is 1 "F increase in temperature for each 67.5 ft increase in depth. The mine produces between 500 and 600 tons per clay, utilizing an adit two internal shafts, and one service shaft from surface. The Queen shaft, extending from the 26 to the 41 level, IS the deepest, and most production now comes from this area. Stoping in by cut and fill using mill tailing hydraulic backfill.

Jan 12, 1963

By Forest Mintz

Many oil and gas producers find it advantageous to borrow against the value of their hydrocarbon re- serves. This paper considers the requirements for a reserve based loan and the calculations that a bank would perform to arrive at a loan amount. Three of the most common loan structures, i.e. a term loan, a production payment, and a revolving credit/term loan will be discussed. A typical outline for each type of loan is presented. Finally, a comparison of major considerations in the three financing techniques is shown.

Jan 1, 1982

By Oliver C. Ralston, Foster Fraas

Electrostatic methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to bene-ficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollas-tonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. The Separator The separator used in these tests is of the nonhomogeneous field type shown in Fig Ia. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll."

Jan 1, 1949

By J. M. Hassler

NOWHERE can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, acid as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone.

Jan 1, 1937

By M. J. Stewart, F. Weinberg

PREVIOUS investigations into convective flow in molten metals have examined systems in which the length-to-height ratio of the enclosure is large, usually using long graphite boats.''2 In normal castings this ratio is generally small and it is not possible to extrapolate the results of previous work to casting configurations. The present investigation was undertaken to examine liquid flow in systems of low length to height ratio. The apparatus used for the experiments is shown in Fig. 1. The molten zone of tin is contained in an aluminum mold of inside dimensions 6.4 by 6.4 by 0.31 cm. A heating block containing a resistance coil is attached to one end of the mold and a cooling block is attached to the other end. These are used to produce a wide range of temperature differences across the mold. The mold is contained in a stainless steel tank which is heated from the outside by resistance heaters to give the required operating temperature during the experiment. Temperature measurements in the molten tin are made with an iron-constantan thermocouple PT equal to 5 atm. The phase diagram derived by us was the same as that found by Krivsky and Schuhmann, except for a similar discrepancy in one boundary line representing the gas composition in equilibrium with SO a. The vapor pressures of the pure components can be neglected at 1700°K, 1 atm and 2500°K, 5 atm. There-fore, in these cases PT is essentially the total pres-sure in the system. This is valid for all the diagrams presented by Krivsky and Schuhmann except for the one at 2500°K and 0.01 atm, where the vapor pressure of silicon is comparable to PT.6 This work was supported in part by the American Iron and Steel Institute. 'C. E. Wicks and F. E. Block: Thermodynamic Properties of 65 Elements, U S. Bur Mines, Bull. No. 605, 1963. R. P. Elliott: Constitution of Binary Alloys, 1st supplementary, McGraw-Hill Book Co., New York, 1965. 3W. A. Krivsky and R. Schuhmann, Jr.: Trans. TMS-AIME, 1961, vol. 221, pp. 898-904. 4M. F. Ancey-Moret, M. Olette, and F. D. Richardson: Mem. Sci. Rev. Met., 1964, vol. 61, pp. 169-76. 5J . F. Elliott and M. Gleiser: Thermochemistry for Steelmaking, vol. 1. Addison-Wesley, Reading, Mass. 1960. 6 J.Drowart, G. De Maria, and M. G. Ingraham: J. Chem. Phys., 1958, vol. 29, p. 1015. probe of 0.4 mm diam inserted into the open top of the mold. Radioactive sn113, in the form of a small sphere, was gently lowered into the molten tin at point A in Fig. 1 THERMOCOUPLE> WATER ARGON END HEATER QUENCH ARGON Fig. 1—Apparatus for detecting liquid flow. Point A indicates position the tracer was introduced.

Jan 1, 1970

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By Ernest F. Burchard

Fluorspar is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluorspar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available. Arizona Fluorspar has been reported as occurring in Arizona in the following localities: near Duncan, Greenlee County; near Naco, Tombstone, and Paradise, Cochise County; Black Mountain, Mojave County; 25 miles southwest of Tucson, and at Helvetia and Silver Bell, Pima County; near Mammoth mine, Pinal County; in Yavapai County, 7 miles from Aguila, and in the Bradshaw Mountains; and near Dome, Yuma County. Production has come principally from the Castle Dome district, Yuma County, with minor quantities from Greenlee, Pima and Yavapai counties. The writer examined deposits in the Castle Dome district, Yuma

Jan 1, 1934

By Earle Schumacher

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10° C. in temperature. The precise location of this line is also important, in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By W. T. Cardwell

Physically absurd, triple-valued saturations appear in the straight-forward solution of the Buckley-Leverell equations for the displacement of oil by water or gas. From an engineering viewpoint, the triple value causen no difficulty. It is well known how it may be compensnted in order to obtain physically meaningful, numerical results. From a scientific viewpoint, the question still arises: What did the triple value mean? This paper explains how and why the triple value arose in non-capillary Buckley-Leverett theory. The discussion should serve as a background for the understanding and use of the modern method of characteristics in di.~pkzc(>ment theory. INTRODUCTION Displacement theory was introduced to petroleum technologists in 1 941 by Buckley and Leverett.' Their first equation, which they wrote down without derivation, was equivalent to the following: ?s/?t= - qr/F ?f/?r (1) where S = saturation of displacing fluid (a fraction) r = time q,. = total volumetric velocity of both the displacing phase and the phase being displaced (usually, but not necessarily, assumed to be a constant) F = porosity (a fraction) f - fraction of the total volumetric velocity that is the volumetric velocity of the displacing phase (assumed to he a function of S only x = distance. Buckley and Leverett called Eq. I "a material balance equation". Actually it is derived from both a continuity equation, or material balance equation, and Darcy's law. Buckley and Leverett jumped from their Eq. 1 immediately to their Eq. 2, which was the equivalent of the following: (?x/?t)x = qr/F df/ds = qr/F f'(s) (2) The jump from Eq. 1 to Eq. 2 involves apparently simple mathematics, but in that apparently simple mathematics lies a subtle point that is part of the key to the meaning of the triple value to be discussed here. Eq. 2 may be readily interpreted as saying that a point of constant saturation (on a saturation-vs-dis-tance curve) moves with a constant velocity that is proportional to the total volumetric rate, inversely proportional to the porosity, and is otherwise a function of the saturation itself. So that if one knows the derivativc with respect to saturation of the fractional flow function, f(S), for each saturation, one knows the velocity of each point of the moving saturation-vs-distance curve. The function f(S) can he determined experimentally and its derivative f'(S) can be calculated. It turns out that the experimentally derived f'(S) is not a monotonic function of S, but instead it has a definite maximum and declines away at both high and low saturations. This in turn means, in accordance with Eq. 2, that on a moving saturation-vs-distance curve, ccrtain intermediate saturations will travel faster than the saturations either higher or lower. The result is indicated in Fig. 1. In Fig. 1, the abscissas represent distances along a column of porous medium, which column is assumed to be uniform in cross-section perpendicular to the ab-scissal direction. The ordinates represent fractions of pore space occupied by the displacing phase, which may be either water or gas. It is assumed that the saturation is uniform over all planes perpendicular to the abscissal direction. The saturation is a function only of time and one space variable. Time variation of the saturation is represented by change in shape of a curve such as curve AGJ, which represents the initial saturation-vs-

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

Another excellent Swedish underground crushing plant is that at Crusher Station 51 of LKAB in Kiruna, Sweden. Bottom-dump rail cars pass over a dump scroll to discharge magnetite ore into a 288 cu yd (220 m3) pocket equipped with a Hewitt Robins E-13 vibrating grizzly feeder. The grizzly section is 59 in. (1500 mm) long and has bar spacings 3 in. (76 mm) wide. Any oversize boulders which will not pass the chute opening to the feeder are blasted. The primary breaker is a Morgardshammar overhead eccentric 55 in. by 71 in. (1400 by 1800 mm) jaw crusher powered by a 200 hp (149 kw) motor. An open side setting of 10. 8 to 11. 8 in (275 to 300 mm) accounts for the high capacity of this crushing unit (2760 stph or 2500 mtph). This figure compares favorably with the capacity of many gyratory crushers but is typical of the Swedish jaw crushing installations, which are often followed by three more stages of crushing or by autogenous grinding. Crushed ore from the jaw crusher is combined with the grizzly under- size in the crushed ore pocket and is fed by a second vibrating grizzly feeder to the secondary cone crusher. Both crushers are serviced by 50/5 ton overhead bridge cranes. During maintenance operations air -operated gates shut off the flow of ore from the dump and primary crushed ore pockets.

Jan 1, 1978

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968