Search Documents

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By J. L. Wyatt

J. W. Tomlison—It seems probable that the author's conclusion, that the conductivity of the slags decreases with increasing content of FeO, is erroneous due to the method of plotting the data. Thus, the results of other workers2,3,13,14 show that the conductivity of molten oxide slags increase with increasing temperature, indicating that the trend of the curve shown by the authors is due to the fact that the data for the slags containing relatively small amounts of FeO are at higher temperatures than those for the slags containing relatively large amounts of this oxide. In this connection the work of Wejnarth2 may be mentioned in which in an investigation of a series of iron silicate slags, the conductivity was found to increase with increasing content of FeO; the fact that the author's slags contained TiO2 probably does not affect the issue since it has been shown15,16 that, at least as far as conductivity is concerned, this oxide behaves essentially the same as silica and that mixtures of the oxide with silica have a very low conductivity of the order of 10-4 mhos at 1750°C. In connection with the experimental technique it may be noted that bubbles of carbon monoxide would probably be produced at the surface of the graphite electrodes in contact with the melts thus rendering the accuracy of the measurements somewhat open to question. J. L. Wyatt (author's reply)—Dr. Tomlinson makes reference to works by Martin and Derge, which indicate that slag systems containing no TiO2 are charac-terized by an increase in conductivity with an increase in temperature. Further, I have cited his examples, which indicate a drastic increase with small temperature change. The results of Dr. Derge's work have no bearing whatsoever on the results of this paper, since the slags under study here contained up to 70 pct TiO2. One cannot generalize on slag systems as a whole on the basis of any one family, for there are definite compounds of ionic nature formed in each system, and the ionic mobilization of these is something that cannot be determined without actual experimentation. Dr. Tomlinson makes reference to an unpublished work which, he claims, shows that titanium dioxide behaves the same as silica in regard to conductivity. Since I have not had 'an opportunity to see the paper I cannot make any comments, but unless the same slag system was studied there can be no specific comparison of results. If the decrease in conductivity of the slag was due entirely to temperature phenomena, as Dr. Tomlinson indicates, then one is without an explanation of the values shown in the paper for slags containing from 10 to 20 pct FeO. I cannot agree that the deviation in findings was appreciably related to temperature change; further, I believe this point was completely covered in the paper. References 13 Endell and Hellbrügge: Glasstech. Ber. (1942) 20, 277. 14 Bockris, Kitchener, Ignatowicz and Tomlinson: Faraday Society. Discussion (1948) 4, 265. 15 Tomlinson: Thesis, London 1949. 10 Bockris, Kitchener, Ignatowicz, and Tomlinson: Unpublished work.

Jan 1, 1951

By G. R. Leverant

RECENT investigations1,2 of the low-cycle fatigue behavior of pure copper under strain cycling conditions have shown that a unique saturation stress level is eventually attained for each value of applied plastic strain amplitude. The dislocation substructure of copper at the saturation stress level is in the form of cells whose diameter decreases with increasing saturation stress level, i.e., plastic strain amplitude. In addition, both the saturation stress level and the cellular substructure are completely reversible. That is, the saturation stress level and accompanying cell size are determined solely by the present conditions of testing and are, therefore, independent of any previous cyclic history. The mechanical and substructural reversibility observed in pure copper, which has a relatively high stacking fault energy, is not observedz for Cu-7.5A1 which has a much lower stacking fault energy. This implies that easy cross slip (wavy slip) is a prerequisite for reversible fatigue behavior. A dispersion of fine, nondeformable particles of a second phase in a metal matrix tends to stabilize substruc- tures introduced by forming operations during subsequent elevated-temperature heat treatments.3 This raises the question as to whether a finely dispersed second phase can induce an element of irre-versibility into the cyclic deformation behavior of a wavy slip material at room temperature, due to partial stabilization of the initially introduced substructure. Since nickel has a higher stacking fault energy than copper,6 pure nickel should be characterized by cyclic reversibility. Therefore, TD-nickel* (Ni-2ThO.r) was

Jan 1, 1968

By Edward J. Felten

Binary Cr-A1 alloys containing from 2.5 to 30 wt pct Al and 0.7 wt pct Y were heated in oxygen, air, and nitrogen between 1000" and 1200°C. The reacLivity of the alloys was found to be dependent both on the alloy composition nnd the nature of t he atmosphere. In oxygen, nllojs containing up to 15 to 20 wt pct A1 reacted to produce an external scale of Crz03 and a subscale consisting Predominently of Al203. Alloys contazning 20 to 30 wt pct A1 react in oxygen to produce an A1203 external scale and little m no subscale. The latter alloys were markedly more oxidation resistant than those of low alurninum content. In air, the alloys on which an external Crz03 scale was formed were found to be permeable to nitrogen ns evidenced by the copious amomts of chromium and aluminum nilrides observed ns part of the subscale. The reactizities in nir (or nitrogen) of these alloys increase <m their aluminurn contents increase. However, alloys on which Al,O, us an external scale is formed were nol culnerable to nccelerated attack in air, and no eltldence of nitvide subscnles were observed. For all alloys, yttrium serwed pYimarily to improve oxide adhrence. THE role of chromium in the oxidation resistance of Fe-Cr alloys &apos;-&apos; and that of aluminum in Fe-Cr-A1 al10s&apos; has received considerable attention in recent years. This is understandable since many of these alloys have excellent oxidation resistance due to the formation of either a Cr203 or a-Ala03 film between the metal and the oxidizing atmosphere. Small additions of yttrium or other rare earth metals are effective in preventing spalling of the protective oxide from the metal substrate."" In contrast, little is known regarding the oxidation resistance of Cr-A1 alloys, although some work has been done by Tumarov et a1.&apos; The poor niechanical properties exhibited by Cr-A1 alloys make them undesirable for use as structural components, but their use as coatings cannot be disregarded. The use of chromium-rich aluminide coatings for refractory metal alloys is an example of the potential use of this type of sytem. The purpose of this work is to examine the oxidation behavior of Cr-A1 alloys containing 2.5 to 30 wt pct A1 and 0.7 wt pct Y. The effects of temperature, atmosphere, and thermal cycling have been determined. EXPERIMENTAL PROCEDURE The alloys used in this investigation can be divided into two groups. Those containing 2.5, 5, 7.5, and 10 wt pct A1 and 0.7 wt pct Y were extensively evaluated in the temperature range from 1000" to 1200°C. Alloys containing 15, 20, 25, and 30 wt pct A1 and 0.7 wt pct Y were tested only at 1200°C. All of the alloys were prepared by standard arc-melting techniques in the form of cylinders approximately 4 in. long and 19 in. in diam. Wafers were cut from the cylinders and subsequently subdivided into rectangular coupons. The alloys were brittle and therefore some cracks were found in almost all specimens. The coupons were prepared for oxidation by mechanically polishing through 600 grit Sic paper, and were thoroughly degreased just prior to testing. Two types of oxidation experiments were conducted, namely; cyclic tests in which the specimens were examined and weighed after each 2 hr exposure, and continuous thermal balance tests run in a controlled atmosphere (oxygen, air, or nitrogen) for 20 hr. In the former test the spalled oxide was not included when the specimens were weighed. The physical condition of a specimen was noted visually after each cycle and testing was continued either to failure or until the performance of the specimen was well characterized. Both Micro and Semi-Micro Thermal Balances (Ains-worth) were used in the continuous tests. The oxidized specimens were sectioned and prepared for metal log raphic examination. The specimens were polished through 600 grit Sic paper. After polishing through 6 and l p diamond, a final mechanical polish with Linde B-Alz03 was used. Specimens containing 2.5 pct A1 were etched electrolytically using a 10 pct oxalic acid solution at 4 v for about 2 sec. Selected specimens were examined in the electron microprobe analyzer. Oxide specimens were examined by standard X-ray diffraction techniques. EXPERIMENTAL RESULTS For convenience, the test results have been broken down according to the exposure temperature, and further subdivided according to the type of test and atmosphere employed. Because of the poor quality of the specimens a larger than normal amount of scatter was observed in the measured rate constants. Also, the evaluation of the weight gain data was done on a somewhat arbitrary basis and may not be truly representative. However, the results obtained do show a significant trend in behavior regarding both alloy composition and the nature of the oxidizing atmosphere. I) Oxidation Behavior at 1000°C. A) Continuous Oxidation estsin Oxygen. This series of experiments was run in the Ainsworth Micro-Thermal Balance using pure oxygen at a pressure of 76 mm Hg. Under these conditions all specimens oxidized in accordance with the parabolic rate law over a major portion of the exposure time; the rate constants appear in Table I. The oxide formed externally on all specimens was predominantly Cr,O,, which was generally adherent. In some cases a slight amount of spalling in the form of a fine powder was noted. a-A1203 was observed as a subscale, along with Yz03 in all alloys. Alloys containing up to 7.5 wt pct A1 oxidize more rapidly than the Cr-0.7Y alloy.

Jan 1, 1970

[THE BLAST FURNACE Blast Furnace U. S.A., M. O. Holowaty, and C. M. Squarcy Part I - Colonial Ironmakers (JOURNAL OF METALS, May, 1957)3 Part II - The Age of Mineral Coal (JOURNAL OF METALS, July, 1957) 9 Part III - From Falling Creek to Zug Island (JOURNAL OF METALS, October, 1957 17 Sterling, Ringwood, and Greenwood, R. W. Shearman and F. Weston Starratt (JOURNAL OF METALS, September, 1959) 23]

Jan 1, 1961

By W. N. Miner, R. O. Elliott

Electrical-resistivity )measurments were made be-trueetz room temperatrive and 1.5 oK on five different stocks of cerium metal, and the results were correlated with the types, amounts, and distribution of the impurities present. Magnesium, which appeared to be distributed as a solute throughout the cerium matrix, was found to have a large effect on the residual resistivity, 1 at. pct Mg being sufficient to increase the residual resistivity by about 10 microhm-cm. The formation of ß by repeated thermal cycling between room temperature and liquid-helium temperature is attributed to the deformation and faulting that occurs during the ? D a transformation. In preparation for starting a proposed study of cerium-rich alloys, we examined samples from severa1 stocks of cerium metal in order to choose the purest stock for future use in making the alloys. Low-temperature electrical-resistivity data were used to gain initial information about the purities of the stocks. Additional information was subsequently obtained from chemical analyses, density measurements, optical metallography, and electron-micro-probe analyses. Cerium that has been annealed at high temperature and cooled to room temperature has the fee crystal structure (? phase) with a = 5.16Å. When cooled further, in the region between about 250" and 150°K, some of the fee phase transforms to the double hcp form (ß phase) with a = 3.68 and c = 11.92Å. The remainder of the room-temperature fee form (and perhaps some of the hexagonal phase) transforms electronically in the vicinity of 100° K to the more dense or "collapsed" fee form (a phase), a - 4.85A, by transferring about 0.5 electron per atom from the 4f level to the valence band. Very little work related specifically to the effects of impurities on the physical properties of cerium has been reported in the literature. Gaume-Mahn1, 2 has studied the effects of calcium, magnesium. iron, silicon, and tantalum on the electrical resistivity and magnetic susceptibility of cerium between 60o and 300°K. Gschneidner, Elliott, and McDonald3 have discussed the effects of total impurity content on the hysteresis of the a —? (reversible) transformation and on the formation of the 4 and "a-? intermediate" phases. Smith and Morrice* have reported the effect of total impurity content on the resistivity of cerium at 4 and 293°K. In none of these reports, however, is it apparent that the distributions of the impurities were determined, L.r., whether the impurities were present in inclusions or in solid solution in the matrix is not mentioned; nor does it appear that the phase purity of the cerium was always considered. In the present study, five different stocks of cerium were involved. One was represented by a single sample of electrowon cerium, which was all that had remained from a stock of high-purity material obtained from the U.S. Bureau of Mines, Reno, Nev., in 1959. The other four stocks were recently purchased from commercial sources and were specified to be 99.9 wt pct pure. EXPERIMENTAL Cerium stocks designated as #1, #2, #4, and #5 were obtained from commercial suppliers for the specific purpose of finding a reliable source of high-purity cerium. Although the purity level of the cerium was specified to be 99.9 pet, the specifications did not include limits as to the amounts of various impurities that would be acceptable. Consequently the chemical analyses of the different stocks varied widely. Stock #3, which had been obtained from the U.S. Bureau of Mines and which was the purest on the basis of chemical analyses, consisted of a single specimen of electrowon cerium. It was included in the examination for purposes of comparison. Table I contains the chemical and spectrographic-

Jan 1, 1968

By E. J. KENNEDY

METHODICAL AND EFFECTIVE: thus may be characterized the fall meeting of the Iron and Steel and Institute of Metals Divisions at the Hotel Statler, Buffalo, N. Y., on Oct. 4 and 5. Approximately 200 registered. Interest centered 1111 the technical papers which were keenly followed, with substantial discussion: During the entire week of the National Metal Congress (Oct. 3 to &apos;i), there were also other sessions of interest&apos; to metallurgists, directed by the America11 Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron arid Steel and Machine Shop Practice Divisions of the American Society of Mechanical En,&apos; the Wire Association and the American Drop Forging Institute. The National Metals Exposition at the 174th Regiment Armory was well attended.

Jan 1, 1932

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By G. S. Baker, S. H. Carpenter

Langenecker has reported significant reduction in strength of high-strength metals during ultrasonic t&apos;ibration. Decreases in static yield stress an order of magnitude greater than the calculated stress amplitude of vibrations were reported by him for a stainless steel and for tungsten. in the present work, attempts were nzadc to verify such large reductions in yield and flats stresses using resonant librations of measured amplitudes. The results show that both the soft metals (copper and aluminum) and the high-strength metals (sleels) hare reductions in yield and .flow stresses no larger than the stress amplitude of libration. BLAHA and Langenecker,&apos; investigating the effect of vibratory stresses on the deformation of zinc and aluminum, found a decrease in the static yield and flow stresses approximately equal to the vibratory stress imposed. Langenecker later extending this work to high-strength metals such as stainless steels and tungsten2 found a much larger effect. In these metals the static yield and flow stresses decreased by an amount more than an order of magnitude greater than the calculated vibratory stresses. It was suggested that this phenomenon could be a serious hazard to high-strength structures in an acoustic environment, such as a large rocket at launch, or could be used advantageously in the working of hard-to-work materials such as the refractory metals. Langenecker and others3 have investigated the effect of high-amplitude vibrations on many metal-forming operations. The results have been quite favorable with usually a large decrease in the energy necessary for the forming operation. The processes, however, involve large frictional forces and it is not clear whether the decreases in forming forces are to be ascribed to decreased friction or to decreased flow stresses. The present paper reports an attempt to determine the effect of accurately known vibratory stresses on the static yield and flow stresses. I) EXPERIMENTAL TECHNIQUE The standard multicomponent resonator technique for measuring internal friction has been adapted to allow simultaneous high-amplitude vibration, internal-friction measurement, and tensile deformation. This has been described in detail elsewhere.4 Longitudinal oscillations of approximately 50 kc frequency are excited in a multicomponent resonator by a quartz transducer. A second transducer measures the amplitude of vibrations. Fig. 1 shows a schematic drawing of the resonator and grip arrangement and the displacement pattern produced. Since the centers of the dummy bars are at displacement nodes, they represent points where attachments will not materially affect the vibrations. The force is applied by a standard Instron tester. The sample may be deformed while simultaneously vibrating at up to 104 strain amplitude. 11) EXPERIMENTAL RESULTS The effect of high-amplitude vibrations on the yield and flow stresses of copper. aluminum, tantalum. a soft iron, and a stainless steel has been measured. In addition samples of tungsten vibrating at stress levels up to 10&apos; dynes per sq cm have been subjected to static stresses near the static yield stress with no indication of macroscopic deformation. Fig. 2 gives typical results for 99.999 pct polycrys-talline copper. A vibratory stress of 7 x 107 dynes per sq cm is applied at points "a" and removed at points "h". The behavior of aluminum is identical. In agree-

Jan 1, 1967

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.&apos;-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b&apos;/a,+Qc/a&apos; [2]

Jan 1, 1963

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-&apos; It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969

By M. J. Hordon, M. A. Wright

The well-defined increase in fatigue life observed o many metals cyclicly strained at vacuum levels below 10-1 to 10-3 torr has been attributed to the critical retardation of oxygen or water vapor chemisorption at the crack tip during crack propagation.1-3 In the absence of strongly adsorbed surface films, crack re-welding during cyclic compression or dislocation escape from the plastic zone around the crack tip has been proposed to account for the observed decrease in the rate of crack growth. The increase in the critical pressure required for the transition in crack growth rate with temperature experimentally determined for aluminum was found to be generally in accord with the adsorption rate model.4 However, although the adsorption mechanism would also predict an increase in transition pressure and fatigue life with increase in cyclic loading rate, and such effects were noted by Snowden5 for lead and Hordon3 for aluminum, the opposite results were reported by Kramer et al.B in studies on aluminum. The present note describes some recent measurements of the fatigue properties of 1100-H14 aluminum at low pressures to determine the specific effect of cyclic strain frequency in the transition pressure range. Flat cantilever-type specimens of 1100-H14 aluminum shaped to produce a uniform strain gradient along the gage length were tested in reverse plane bending at constant deflection amplitudes in two independent multi-specimen vacuum fatigue systems. One series of tests using 2-in. gage length specimens was conducted in an ion pumped apparatus with 107 torr and 50 cps capacity, denoted as Unit I, utilizing fixed mechanical cams to impose the strain amplitude. An independent test series using shorter 1-in. gage length specimens was conducted in a cryopumped apparatus designed for extremely low pressures below 10-10 torr, denoted as Unit II, using an electromechanical vibrator at non-resonant frequencies up to 150 cps to provide the deflection. Both vacuum fatigue units and associated test procedures have been described previously.3&apos;7

Jan 1, 1969

By F. R. Hensel

THE alloy under discussion is a nickel-silicon bronze and is one of many age-hardening or precipitation-hardening FIG. I.-EFFECT OF QUENCHING AND AGING TEMPERATURES ON HARDNESS OF TWO TYPICAL NICKEL-SILICON BRONZES, NO. 2351 AND No. 2362. copper-base alloys. The hardening con-stituent is a nickel-silicon compound.1 The quenching temperature necessary to pro-duce hardening by a subsequent aging treatment is a function of the composition and extends from about 700&apos;C. to ()50&apos;C.; the aging temperature range extends from 400° to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Si; balance, copper.

Jan 1, 1940

By W. T. Burns

Attempts were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No. 1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles. The average composition of the furnace charges was as follows: Per Cent. Peer Cent. Copper. Precipitate,..........7.5.3 40 to 80 Purification cathodes,.....1.9 92 Refinery slag (oxide slag),.. 10.1 50 to 60 Electrolytic cathodes,... 2.1 99.9 Precipitate anode scrap,.... 3.1 99.0 Scrap copper,.........7.5 99.2 100.0 The slag from this furnace amounted to 46 per cent. of the total amount charged and was of the following average composition: Per Cent. Cu..............16.86 SiO2.............34.7 FeO.............18.8 A12O3.............13.0 CaO.............9.4 MgO.............2.7 S............... 0.47 As..............0.11 Sb...............0.006 Ag, oz per ton.....0.18

Jan 1, 1914

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,&apos; or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By T. D. Yensen

EFFECT OF ELEMENTS ON MAGNETIC PROPERTIES OF IRON THE elements aluminum,1 arsenic,2 silicon,3 tin2 and vanadium,4,8 when used in relatively small amounts as alloying elements, seem to have a beneficial effect on the magnetic properties of iron-i. e., they increase the maximum permeability and decrease the coercive force-whereas there are definite indications that boron,5 carbon,6 nitrogen,7 oxygen,8&apos; phosphorus,6 sulfur6 and titanium,4 as well as the metals of and adjacent to the ferro-magnetic group, nickel,9 cobalt,10 copper,11 and manganese,6 have a detrimental effect on these properties. The effects of calcium4 and magnesium4 are small, if any, while the effect of chromium 12 in small amounts is unknown and in large amounts is generally detrimental.

Jan 1, 1931