Search Documents

By John Freeman

THE die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the, minimum amount of scrap to be sheared from the pressing as it comes from the-die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By F. W. McQuiston

Idarado Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation I2,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. Ores The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper. lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galenn is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (I) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic inter-growth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. Plant Practice Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1949

The Report on the Manufacture of Coke for the year 1880 by J. D. Weeks1 includes an historical account of the early days of coke-making that is very complete and accurate, and but little can be added to it to fully cover the period prior to 1885. The few additional references that have been found follow. The earliest suggestion found about making coke in this country is in a letter from D. M. Randolph to Harry Heth, dated August 22, 1808. Heth was then operating the mines in the Richmond, Virginia coal field and had sent Randolph to England to investigate steam engines for hoisting and pumping and other conditions in the coal industry there. The letter was written in London and said: "I shall explain to you, how, by turning Deep Run fine coal in Coak, to make great profit from what has heretofore been useless. You will do well to ascertain the price and amount of demand for this article throughout the U. States among brewers and manufacturers. I know how also to make every bushel of such fine slaty coal, fetch as much as any of the best grate coal, by turning it into Coak: and that too, after paying all expenses of the process."2 His interest was to use the slack more for domestic purposes than otherwise, probably, although what the interest of brewers would be in coke as fuel does not appear. Nothing ever came of this suggestion, and so far as known, no coal from this field was coked excepting in gas-making. The Plumpsock Iron Works, mentioned by Weeks as having used coke, was advertised for sale in June 1818.3 It was stated that stone coal was the only fuel used at the works, the pit being within 100 yards of the forge. "Three men with a horse and cart are sufficient to raise coke, and haul to the forge all the coal necessary for keeping the works in full operation." The coke, of course, was made in ricks, or heaps, and not in ovens. The first real coke oven in this country was probably built in Connellsville, the coal coming from a mine nearby on Mounts Creek. L. L. Norton operated an iron foundry and was persuaded by his foreman, one Nichols, who came from Durham, England to build a coke oven. The oven was 12 feet square, and the first coke was produced in 1833. Later

Jan 1, 1942

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By W. A. Bates, R. J. Miller

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By R. J. Miller, W. A. Bates

Although cresylic acids have been standard frothers in flotation for many years, there has been little discussion of their nature in the metallurgical literature. Aside from references in the patent literature, the paper by Landolt, Hill, and Lowyl in 1930, which resented a study of the frothing and collecting properties of some of the constituents of crude cresylic acids, represents the only contribution of this type. The close froth control required in the delicate selective separations of present-day flotation operations have required the flotation metallurgist to choose his frothers with care, and have caused him to require of the manufacturer a closely controlled, uniform product. A background of knowledge of the chemical composition and physical and chemical properties of the frothers, by which their action may be correlated, should aid in selecting frothers for particular flotation requirements. Further, the recent almost complete replacement in flotation of coal-tar cresylic acids by those derived from petroleum makes it especially desirable to review the flotation behavior of the acids from the old and the new sources. In view of these facts the Milling Methods Committee of the A.I.M.E. suggested to the Oronite Chemical Co. of San Francisco the preparation of a paper on the subject, and this paper has accordingly been prepared as a contribution by the California Research Corporation, the research affiliate of the Oronite Chemical Co. The discussion is from the following aspects: (I) constitution and properties; (2) sources; (3) comparison of coal-tar and petroleum cresylic acids; (4) characteristics as frothers, with particular reference to the effect of the substitution of petroleum acids for coal-tar acids. Constitution and Properties Cresylic acids are commonly regarded as mixtures of orthocresol, metacresol and paracresol. This was, indeed, the former meaning of the term, but in recent years it has been loosely applied to any mixture of alkyl phenols boiling above 190°C.; that is, excluding only phenol itself. This means that cresylic acids, as they are known today, may consist of mixtures, not only of the three isomeric cresols, but of six xylenols and of a variety of higher boiling homologues. Generically the constituents of cresylic acids are alkyl phenols, and they are often so designated in the literature to avoid the more indefinite term, "cresylic acids." They form an homologous series starting with phenol, which has the familiar benzene ring, with an hydroxyl group in place of one of the hydrogen atoms. The series of alkyl phenols is formed by the substitution of alkyl side chains, such as methyl, ethyl, propyl, butyl, etc., for hydrogen atoms of the benzene ring of phenol. Some

Jan 1, 1947

By A. L. Holley

THERE is a growing demand for pure and cheap material for fine open-hearth steel ; a material not only very free from phosphorus, but from carbon and silicon; so that it may he rapidly converted into steel. Iron and steel scrap are not trustworthy as to quality, and they are often dear. There are three methods of purifying cheap materials for the open hearth. 1. Mechanical puddling, as done at Creusot, which removes 90' per cent. of the phosphorus from the pig iron. 2. Krupp's washing process (the conduct and results of which I fully described in a former paper*), which eliminates 70 to 80 per cent. of the phosphorus and most of the sulphur and silicon from pig iron. Neither of these processes would sufficiently purify, for very fine steel, those very impure pigs which are cheapest in many parts of the United States: 3. The process of producing directly from the ore an iron which is practically pure chemically, although mechanically mixed with the impurities of the ore. This is the oldest of iron processes ; one form of it, the Catalan forge, employed to produce charcoal blooms, is still in use, but its great cost is rapidly throwing it out of competition. Among the modern attempts to produce iron direct from the one, on a large scale and at a cheap rate, several have been in various respects successful. Dr. Siemens's process of treating a ton and a half or more of ore and the coal to deoxidize it, in a rotating gas furnace, and bringing out, in some four hours, a ball of chemically pure iron so soft that the fluid and impure slag may be squeezed out of it, is the most attractive and the most highly developed of all the modern direct processes. I have watched it, from time to time, since 1874, and have noted a steady improvement. It may now be said to have passed the experimental stage, although, like older processes, it must be adapted by practice to special materials. The cause which has been more potent than all others, including the defects of the best direct processes, to bring these processes into disrepute, is the waste-ful treatment of the direct product. With one or two exceptions (when failure was due to other and obvious causes), the direct product has been made into wrought iron (weld iron). Even Dr. Siemens has, at Towcester, in England, and at Park, Bro. & Co.'s, in Pittsburg, set up his apparatus for this purpose. Is it likely that

Jan 1, 1880

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

T. R. HARRISON, Washington, D. C. (written discussion). *-Mr. Kowalke shows that a high resistance millivoltmeter is subject to smaller errors, due to change in resistance of the thermocouple to which it is attached, than is a low-resistance instrument. He uses as examples instruments having resistances of 30 and 2 ohms, respectively. At the Bureau of Standards, resistances above 300 ohms would be considered high and 30 ohms rather low. In the tests on calorized-iron thermocouples, a difference between the first and third calibrations of the couples serves to show changes due to the intermediate heat treatment and only under certain conditions would changes in calibrations due to changes in the wire be detected by ,a recalibration after 1 1/2 in. had been cut from the hot-junction end of the couple and the ends rewelded. The calibration of a couple depends only on the thermoelectric prop-erties of that part of the couple which lies within the region of non-uniform temperature, i.e., the temperature gradient; hence, so long as the temperature gradient falls along wires of similar thermoelectric properties no change in the electromotive force is produced by altering the metals of those parts of the circuit that are at uniform temperature. Usually at the cold-junction end of the circuit, copper leads, brass binding posts, manganin resistance coils, and various other materials form part of the circuit, but so long as all are at a uniform temperature (or if for each junction between unlike metals there is a similar opposing junction at the same temperature) no resultant thermoelectromotive force will be produced thereby. Likewise, if a length of several inches at the hot-junction end of the couple is at uniform temperature, it matters not if this section is unlike other parts of the couple, so long as there is good metallic connection and no source of e.m.f. other than thermoelectric is present. Cutting off part of the hot end of the couple within such a region of uni-form temperature would not alter the e.m.f. of the couple.

Jan 12, 1919

By C. R. Boyd

The sulphuretted ores of Carroll and Grayson Counties, Va., Ore Knob, Ashe County, N. C., and Ducktown, Tenn., in their general position, are in the prolongation of the same massive deposits. The existence of the extensive ore-bodies has been well-established, not only in a practical way, but by the careful research of a number of men of science, including Dr. T. S. Hunt, Professor Kerr, Dr. Genth, Rogers, Safford, Professor Egleston, Dr. H. E. Colton, the writer, and others, and described in one or more of the volumes of our Transactions, as well as in other publications. The greater quantity of' these ores being pyrrhotite, although much of them carry nonmagnetic disulphide, their reduction on the gronnd will probably lead to better results than an attempt to mine and ship them to distant places; and their use as sulphuric acid producers, to be employed in the cheap manufacture of valuable fertilizers, will be chiefly the subject of this paper. The great deposits of Carroll County, Va., are now nearer to railway transportation than any of the others, being six to eight miles from the Cripple Creek extension of the Norfolk and Western Railway, now being constructed, the grading of which is in an advanced state of completion. I am not able to state what are the present prospects of an early completion of the contemplated line of railway to Ducktown. For a long while, during the time those deposits were mined and reduced for their copper, the works were forty miles from any railway ; and the same may be said of Ore Knob, N. C. The deposits in Carroll and Grayson Counties, Va., being now the most accessible to cheap transportation, will naturally claim the greater part of our attention ; though it may be pertinent to remark, just here, that the ores of Ducktown, like those of Carroll and Grayson, Va., exist in the undecomposed levels as iron and copper sulphurets, much of which is a non-magnetic disulphide, as stated, with occasional exhibits of sulphides, such as covellite, erubescite, etc. There are, now and then, small quantities of silver, lead, and zinc,

Jan 1, 1886

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

Iron Ores and Blast Furnace Practice Concentration of Iron Ores in the United States. By T. R. Counselman. (Metals Technolog), December 1943) Selection of Blast-furnace Refractories. By Hobart M. KrANer and E. B. Snyder. (Metals Technology, April 1944) The Washing of Pittsburgh Coking Coals and Results Obtained on Blast Furnaces. By C. 1). King. (Metals Technology, September 1943) Steelmaking The Role of Basic Slags in the Elimination of Phosphorus from Steel. By Richard L. BArrett and William J. McCaughey. (Metals Technology, April 1944) The Relative Deoxidizing Power of Boron In Liquid Steel and the Elimination of Boron in the Open-hearth Process. By B. W. Gurry. (Metals 'Technology, December 1943) Manufacture and Properties of Killed Bessemer Steel. By C. C. Wright. (Metals Technology, June 1944) Hardenability Effect of Sixteen Alloying Elements on Hardenability of Steel. By Irvin R. Kramer, Robert Hafner and Stewart L. Toleman. (Metals Technology, September 1943) Effect of Quenching Temperature on the Results of the End-quench Hardenability Test. By Clarence E. Jackson and Arthur L. Chrjstenson. (Metals Technology, December 1943) Effect of Some Elements on Hardenability. By Walter Crafts and John L. Lamont. (Metals Technology, January 1944) Effect of Several Variables on the Hardenability of High-carbon Steels. By I?. S. Rowland, J. Welchner and R. IS. Marshall. (Metals Technology, January 1944) Mechanical Properties Influence of Hydrogen on Mechanical Properties of Some Low-carbon Manganese-iron Alloys and on Hadfield Manganese Steel. By Herbert H. Uhlig. (Metals Technology, June 1944) Aging and the Yield Point in Steel. By J. R. LOW, Jr., and 14. Gensamer. (Metals Technology, December 1943) Tensile Properties of Medium-carbon Low-alloy Cast Steels. By H. A. Schwartz and W. Kenneth Bock. (Metals Technology, August 1944) Variables Affecting the Results of Notched-bar 1mpct Tests on Steels. By CLarence 15. Jackson, MYRon A. Pugancz and Frank S. McKenna. (Metals Technology, August 1944) The Notched-bar Lmpact Test. By John H. Hollomon. (Meta1s Technology, April 1944) Hardness Measurement as a Rapid Means for Determining Carbon Content of Carhon and Low- alloy Steels. By K. L. Clark and NIcHols Kowall. (Metals Technology, January 1944)

Jan 1, 1944

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts'2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By Charles T. Holland

IN connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter [ ] into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. STRENGTH OF COAL It is generally agreed that one of the necessary conditions for bumps is a strong [ ] coal.1 Therefore, since the strength of coal is an important factor, a study of this property should be made. Several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines8 and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semibituminous (Pocahontas No. 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the same coal.

Jan 1, 1942

By C. L. Baker

The total production of petroleum in the Gulf Coast in 1927 was 54.541.180 bbl., .5.655.665 bbl. more than in 1926. The Texas total was 49.129.910 bbl. (Table 1) and the Louisiana tota1 5.411.270 bbl. (Table 2). Louisiana production decreased 278.028 bbl., compared with that of 1926. Spindletop produced nearly 44 per cent. of the Texas total. Initial production in Louisiana amounted to 62.865 bbl. and in Texas to 352.955 bbl.' The Oil and Gas Journal gives a total of 1145 wells

Jan 1, 1928

By J. W. Cuthbertson, R. A. Cresswell

THE constitution of Cu-rich alloys with 1.5 to 13.5 pct Sn and 0.25 to 3.0 pct Be and the precipitation-hardening characteristics of alloys with 1.5 to 13.5 pct Sn and 0.25 to 1.0 pct Be have been examined. The hardness and tensile strength of the alloys examined increase markedly after solution treatment at 700°C followed by heat treatment at temperatures between 200" and 450°C. By a combination of cold work and heat treatment, hardness values similar to those exhibited by commercial Be-Cu alloys containing 2.25 pct Be can be obtained with ternary alloys containing 9 pct Sn and 0.75 pct Be and containing 10 pct Sn and 0.5 pct Be. Marked hardening effects occur with alloys containing even less beryllium. By heat treatment alone, a hardness value of 310 diamond pyramid hardness can be obtained from an alloy containing 10 pct Sn and 0.75 pct Be. Preliminary tensile tests have shown that an ultimate tensile strength of 110,000 psi with an elongation of 23 pct is obtainable by precipitation hardening an alloy with 8 pct Sn and 0.75 pct Be. The precipitation-hardening process has been followed microscopically for certain alloys and the inference is that, while the initial hardening effect is probably explained by the precipitation of the ß phase of the Cu-Be system, further hardening, proceeding at a much slower rate, also occurs, apparently as a result of precipitation of phases of the Cu-Sn system, particularly precipitation of the 6 phase at temperatures below 350". The presence of the e phase of the Cu-Sn system in certain alloys at temperatures below 350°C has been confirmed. Tin-bronzes are widely used in engineering applications where a combination of high strength and good resistance to corrosion is wanted. The maximum strength is induced in these alloys by cold working, and it would be an advantage for many purposes if high strength could be achieved alternatively by an age-hardening process. While Cu-Sn alloys have a good fatigue resistance they can be surpassed in this respect by Cu-Be, but the use of the latter alloy is limited by its high cost. If, by adding beryllium to tin-bronze, the properties of the respective binary alloys could to some extent be combined, a most attractive alloy should result. As pointed out by Raynor,¹ beryllium is on the borderline of the zone of favorable size factors for copper, and the solid solubility of beryllium in copper is consequently much more restricted than if the size factor were strongly favorable. The size factor is sufficiently favorable, however, to permit an increase in solid solubility with rise in temperature, and there is thus a composition range in which CU- Be alloys are susceptible to hardening by precipitation heat treatment. Although the a phase of the Cu-Sn system is similarly susceptible to precipitation treatment, the time necessary to establish equilibrium in commercial alloys of this type is usually so great that age hardening becomes impracticable. The addition of beryllium to Cu-Sn alloys would appear to offer a means of conferring on the latter useful age-hardening properties. Masing and Dahl² and others have, in fact, shown that the addition of beryllium to Cu-Sn a solid solutions renders these alloys susceptible to precipitation hardening and after such hardening confers on them an encouraging improvement in physical properties. If this improvement could be achieved by the addition of substantially smaller amounts of beryllium than are customarily found in binary Cu-Be alloys, the ternary alloys should possess economic advantages which might make them more attractive than the binary alloy for some applications. Binary Systems Copper-Tin: The constitution of these alloys is now reasonably well known and is summarized in the equilibrium diagram published by Raynor.³ The following observations, due to Raynor,¹ on the structure of those phases of the Cu-Sn system that are likely to be found in the ternary alloy system will facilitate the subsequent discussion on the examination of that system. The ß phase is an electron compound at the electron-atom ratio 3:2 and has a body-centered cubic crystal structure. This phase is stable only down to 586°C, at which temperature it decomposes eutectoidally into the a and y phases. The y phase has a structure that is also based on the cubic system. This phase is stable down to 520°C, at which temperature it decomposes eutectoidally into the a and d phases. The d phase is an electron compound (Cu³¹Sn8) which has a crystal structure analogous to that of 7 brass. This phase is stable from 590" to 350°C; on prolonged annealing at the latter temperature it breaks down into a mixture of the a and E phases. The e phase is an electron compound (Cu³Sn) having the electron-atom ratio 7:4. Its structure may be regarded as a superlattice based on the close-packed hexagonal system. This phase is stable from 676°C to room temperature. The primary solid solubility of tin in copper increases to a maximum of 15.8 pct as the temperature falls from that of the peritectic reaction to 586°C. The solid solubility remains constant from 586" to 520°C. At lower temperatures the solubility decreases progressively. Below 350°C the fall in solubility is pronounced and is associated with the precipitation of the e phase. This precipitation is very sluggish and does not normally occur under service conditions. Copper-Beryllium: The Cu-Be system has been investigated by Borchers' and others. Raynor5 summarized the present state of information on it.

Jan 1, 1952

By Henry Faul

MEASUREMENT of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (I) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quantitative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carnotite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement.

Jan 1, 1947