Search Documents

By Wilbur C. Helt

The United States is self-sufficient in bituminous coal and lignite resources to meet the high range of energy demands forecast for the remainder of this century and beyond. The known or proved recoverable reserves of energy from coal in the United States are estimated to be 88% of all fuel reserves, whereas the energy reserves for oil are estimated to be 276, gas 376, shale oil 5% and uranium 2% (as now used). The demand for all forms of energy used in the United States is increasing at a rate of 3% to 4% per year. Presently, coal is competitive on a supply and cost basis with other fuels in conversion to electrical energy and as a source of energy for converting raw minerals to metals and nonmetals, but it is not competitive in transportation and other uses that demand the high flexibility that oil and gas enjoy because of their form. Coal conversion to fluid forms is essential to make it interchangeable with gas and oil to meet the markets they now occupy. Essentially, the chemical constituents that make up coal are the same hydrocarbons that make up oil and gas; it is a matter of reconstituting the proportions of hydrocarbons to make coal interchangeable with the other fuels. The production of coal has fluctuated widely between the peak production of 631 million tons in 1947 to a low of 403 million tons in 1961. Throughout this period, the total value of the production, f.o.b. mines, has averaged more than $2 billion annually. Beginning with 1962, there has been a steady upward trend in coal production with only minor fluctuations that were mainly caused by labor disputes. Output for the latest typical year, 1970, was 588 million tons. Production in 1971 was affected by a major strike and dropped to 548 million tons. Exports of coal from United States to foreign countries have increased steadily and developed into a substantial annual market for over 71 million tons per year. About 56 million tons of this is suitable for metallurgical purposes, and the remaining 15 million tons is exported for electric power generation. The largest single-industry demand for coal is in the electric generating industry, Fig.1. Roughly, the production of electricity has doubled every

Jan 1, 1973

By A. O. Bartell

Do you know that valuable clues to the geology and mineralization of a district can be found in a handful of sand from a stream bed draining the area? This handful of sand has a story to tell to those who have a little patience. The handful of sand may contain tiny specks of valuable minerals (gold, scheelite, cinnabar, chromite, tourmaline-to mention a few), that will lure you upstream with the hope of uncovering a new deposit. More practically, this handful of sand can indicate the type of rocks that are exposed by the drainage system. Any mineral that has a specific gravity of 3.5 or higher can be separated from soil by panning. Garnet and pyrite, for example, can indicate an outcrop of metamorphic rock. In one district where the writer prospected, small boat-shaped orthorhombic crystals of topaz always indicated the presence of andesite outcrops.

Jan 1, 1948

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1941

By H. D. Colson, Robert A. Rapp

When a binary alloy is oxidized to form simultaneously an internal oxidation zone and an external scale which grows at a constant rate, the oxidation should reach a condition of steady shale, in which the internal oxidation zone is maintained at a time-independent thickness. Assuming an ideal model for the steady-state oxidation, the diffusion equation is solved for the steudy-state concentration profiles for oxygen and alloying- element in the metal. A theoretical prediction of' the steady-state thickness of the internal oxidation zone is made in terms of the experimental parameters. FOR the oxidation of binary alloys, Rhines, Johnson, and Anderson,1 as well as Mask: have derived equations describing the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which was assumed to mow according to a parabolic rate law. Experimental determinations of internal oxidation zone thicknesses beneath a Cu2O scale for Cu-Be and Cu-A1 alloys3,4 have shown some deviation from Maak's theoretical expressions, because the ideal model assumed for the calculation is not met experimentally. Some pure metals, such as columbium and tantalum oxidize at elevated temperatures and high oxygen pressures to form nonprotec-tive external scales which thicken at a constant rate. If such a base metal is alloyed with a solute element which may form a more stable oxide than the solvent oxide, then internal oxidation of solute may occur beneath the growing external scale. A review of the internal oxidation of alloys has been published recently.5 The purpose of this paper is to analyze theoretically for a binary alloy the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which grows at a constant rate. Consider an alloy A-B in which A is the more-noble solvent and B is the less-noble solute. The solute oxide is assumed to precipitate in internal oxidation as stoichiometric particles of BO, which are assumed to have a negligible solubility product in the A matrix. It is further assumed that the diffusion of oxygen through the zone of internal oxidation is not impeded by previously precipitated BO, particles. The specimen is assumed to be sufficiently thick so that the solute content in the center of the specimen does not change. For consistency: the following notation of Maak2 has been used:

Jan 1, 1967

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1943

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1939

By Reinhardt Schuhmann JR

Metallurgical Engineering Volume I, by Reinhardt Schuhmann, Jr. Addison-Wesley Press. $7.50, 390 pp., 1952. -This first volume, engineering principles, of a two volume work, is intended by the author to meet a need for reorganization of instruction in extractive metallurgy. Its three main objectives are to organize the subject matter according to basic principles and unit processes; to integrate the underlying science of physical chemistry with metallurgical engineering; and to put greater emphasis on analysis and quantitative solution of engineering problems. Vol. I deals with unit processes, stoichiometry, thermodynamics, fuels, fluid flow, heat transfer, pyrometallurgical systems and refractories. Vol. II will take up the individual unit processes. Initiation and Growth of Explosion in Liquids and Solids, by F. P. Bowden and A. D. Yoffe. Cambridge University Press. $4.50, 104 pp., 1952.-The book is a study of decomposition by impact and by friction of explosive substances and deals mainly with the work of the authors and their collaborators. Research is still in progress but results thus far indicate that the mechanism of initiation is relatively simple. Findings are thoroughly discussed, and the latter part of the monograph describes the way in which a small nucleus of decomposition can grow into a large scale explosion.

Jan 1, 1952

TWO hundred enthusiastic engineers and coal, op-erators attended a joint meeting of the A. I. M. E., the National Coal Association, and the American So-ciety of Mechanical Engineers in the auditorium of the Alabama Power Co. building at Birmingham, Ala., on Jan. 21. S. W. Farnham, mining engineer of the Goodman Manufacturing Co., Chicago, in his paper on mechanical loading of coal discussed the feasibility of scraper and machine loading. A. R. Anderson of the Jeffrey Manufacturing Co., in a paper on loading coal with conveyors covered their adaptation for long-wall mining and for loading into cars. Discussion of these papers was hampered because the cheap labor costs prevailing in the district have handicapped gen-eral mechanization of the mines. The Bureau of Mines film, "The Story of a Rock-dusted Mine," showing the New Orient mine, West Frankfort, Ill., was also shown at the meeting. F. H. Crockard, president of the Wood-ward Iron Co., represented the A. I. M. E., S. L. Yerkes, vice-president of the Grider Coal Sales Agency, and J. L. Davidson, secretary of the Alabama Mining Institute, represented the National Coal Association, and Paul Wright represented the American Society of Mechan-ical Engineers.

Jan 2, 1927

By D. Mizer, J. B. Clark

In a recent investigation of the entire magnesium-yttrium phase diagram, Gibson and Carlsonl report the maximum solid solubility of yttrium in magnesium as 8.0 wt pct Y at 1050°F (565°C). However, independent studies of the precipitation in magnesium-yttrium alloys, 2 conducted prior to the publication of the above phase diagram, indicated a greater solid solubility of yttrium in magnesium. Accordingly, the magnesium-rich region of the diagram was re-investigated to determine more accurately the liqui-dus, solidus, and solvus of the magnesium solid solution in this system. Metallography and thermal analysis were chosen as the best corroboratory methods for accurately determining this region of the diagram. A magnesium-yttrium master alloy was prepared from yttrium of 99.9 pct purity and singly sublimed magnesium of 99.9 pct purity. Subsequently, the twelve magnesium-yttrium alloys shown in Fig. 1 were prepared using standard alloying procedures for magnesium. Metallographic samples of the alloys were heat treated under an SO, atmosphere in an electric furnace capable of control within ±3oF of the desired temperature. Alloy samples for the metallographic determination of the solvus, and for the precipitation studies were solution treated at 1000° F for 16 hr. Subsequent aging times for the solvus determination varied from a minimum of 6 hr for the higher temperatures up to 816 hr for lower temperatures. Periods of 30 min at temperature were used to generate liquation for the metallographic placement of the solidus and eutectic horizontal. The liquidus and the eutectic horizontal were determined by thermal analysis. Simple time-temper- ature heating and cooling curves were obtained from 10-g alloy samples heated and cooled in a well-insulated electric furnace. An Iron-Constantan thermocouple was placed in direct contact with the sample. The thermocouple did not contaminate the alloy sample since metallographic examination showed that the alloy melt did not wet or attack the thermocouple. The heating and cooling rates were approximately 5 to 8OF per min. The standard metallographic procedures for magnesium were used in polishing and etching the magnesium-yttrium alloys studied. Glycol etchant* was etchant was used to reveal precipitate in the solvus determination. The redetermined magnesium-rich region of the magnesium-yttrium diagram is shown in Fig. 1. The

Jan 1, 1962

IF you do not make the disc at the same time as the core and as part of it, it is necessary to make it by itself. This is done by spreading on a board or other flat surface a layer of clay as thick and wide as [88] the disc that you made at the feeding head of the first pattern of the gun. When it is dry, mark it exactly with compasses and then, cutting with a chisel or rasp, make it fit exactly into the empty space at the head. Likewise, make a hole just as wide as the thickness of the core exactly in the middle of this clay disc. When you have put the disc in its place in the mould and then pass the core through this hole, it passes exactly through the center of the mould in such a way that it meets the iron ring that you put at the foot of the mould for this purpose. As I said above, if' you do not make it as part of the core, it is necessary to proceed in the aforesaid way. But if' you wish to make it attached to the core (which I like better because it can be done more accurately) make a

Jan 1, 1942

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1934

By Elliot P. Rexford

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By Elliot P. Rexford

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By J. L. Wyatt

THE strain sensitivity, K, a property of metals defined as the unit change in electrical resistance per unit strain, was measured for commercial purity titanium wire to determine its usefulness as a strain gage material. A Kelvin double bridge, accurate to 0.000001 ohm, was used to make measurements from 0 to 1 pct total strain. A positive value of 0.17 for K was found. This compares with 2.15 for constantan and 3.5 for cold-worked invar, two of the more common strain gage materials. The effect of temperature also was determined. It was found that a change in temperature of 30°F caused the same resistance change as 1 pct strain. It is therefore concluded that titanium would have utility as a strain gage only if the thermal fluctuations in the specimen could be controlled to a high degree and in applications of very large total strain.

Jan 1, 1953

By L. D. Jaffe

THE data recently published1-" on heat treatment of titanium alloys have not been readily systematized into an overall picture. When the ß titanium phase transforms isothermally at low temperatures, the hardness follows a typical age-hardening pattern, going through a peak as schematized by the "hardness" vs "time of isothermal transformation" coordinates of Fig. 1. As the temperature is raised, the peak will decrease in height and occur at shorter times; slowing must however take place as the /3 transus is approached. The brittle microconstituent in the region of peak hardness has been termed /3'. Its structure is still undetermined but it is clearly a transition stage from soft /3 to the £ + a that is found at the right of the peak. On continuous cooling, high cooling rates correspond to short times on Fig. 1; abscissa labeling has been added accordingly. Extremely rapid cooling will retain soft /3; very slow cooling will precipitate soft a; intermediate rates give hard 8'. Increasing distance from the water-quenched end of a Jominy hardenability bar corresponds to slower cooling (right on Fig. I), but the range of cooling rates covered by a Jominy bar is only a small portion of that shown in the figure. The p-stabilizing alloying elements retard the transformation process, moving the material to the left on Fig. 1. A lean alloy is harder water-quenched (P') than air-cooled (/3 +a); a rich alloy is harder air-cooled (/3') than water-quenched (/3). Examples of the position of various compositions with respect to the curve, based on limited data in the literature, are given at the top of the figure. Oxygen and carbon accelerate the transformation process, moving the material to the right on Fig. 1. If an alloy quenched quickly enough to retain soft /3 is reheated below the £ transus (tempered), it ages, going through a hardness maximum as time increases (moving right on Fig. 1). Material which after cooling from the /3 range lies on or right of the hardness peak, will move still further right on tempering, and so soften. Since the rate of the tempering (aging) reaction increases with temperature, the figure also may be used to represent the variation in properties with tempering temperature, at short tempering times. The simple picture given here neglects martensite transformation, as well as differences between decomposition products of /3 formed by direct isothermal transformation and those formed by quenching and tempering. It may nevertheless be of use as a guide for practical heat treatment and for further research.

Jan 1, 1955

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry' extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.' These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

By Orvar Nyquist, Klaus W. K. Lange, John Chipman

Liquid Fe-C-Si alloys containing 0 to 12 pet Si and up to 4 pet C were equilibrated with carburizing gases at 1550°C. Two to 5 alloys simultaneously were held in close proximity for 5 to 7 hr to establish uniform carbon activity in the group. Analysis of the data gives the activity coefficient of carbon as a function of the mole fractions of carbon and silicon, Fig. 7. Values of the interaction coefficients at infinite dilution are

Jan 1, 1962

By M. E. Wadsworth, I. B. Cutler, R. W. Bartlett

The oxidation kinetics of ZrC was studied between 450" and 580°C in oxygen pressures from 6.5 x 10-to 1 atm using a ther mogravimetric apparatus and sized powder samples. Two parallel rate controlling processes were observed. A surface reaction occurring at the ZrC-ZrO2 phase boundary accounted for most of the oxidation and had an activation enthalpy of 46 kcal per mole. The other process, believed to be diffusion of oxygen into the ZrC lattice partially replacing carbon, had an activation enthalpy of 53 kcal per mole. The enthalpy for chemisorption of O2 on ZrC was determined to be —13 kcal per mole. Water vapor in the presence of oxygen accelerated the surface reaction rate. THERE has been little reporting of formal rate studies or attempts to ascertain the mechanism of oxidation of carbides. MacDonald and Ransley1 studied the oxidation of titanium carbide which has the same structure as zirconium carbide, fcc. They observed an initial increase in rate with increasing temperature followed by a rapid decrease through a rate minimum and a subsequent second increase at higher temperatures. The discontinuity in the rate rise was attributed to a phase change in the oxide which changed the rate determining step from the surface reaction at the carbide-oxide interface to diffusion through the oxide layer. Samsonov and Golybera 2 studied titanium carbide and reported that during the initial period of oxidation a dense film of Tic-TiO was formed followed by the formation of less adhering layers of higher oxides. The purpose of this investigation was to study the kinetics of oxidation of zirconium carbide and to attempt to gain some knowledge of the mechanism by which oxidation occurs. EXPERIMENTAL PROCEDURE Measurement of the weight gain associated with the oxidation of ZrC was used to determine oxidation rates. The principal experimental parameters were surface area, temperature, and oxygen pressure. Although moderately sized crystals of ZrC can be grown by the Van Arkel method, the only commercially available ZrC is a powder. In using powders, the surface area must be controlled either by fabricating the powder into a sintered pellet with a measurable surface area, relatively fixed during oxidation, or by using sized unconsolidated powder and applying appropriate geometric considerations to the shape of the grains to correct for their diminishing surface areas as they oxidize. Both techniques involve some difficulties. pellets of binder-free zirconium carbide can be made by hot pressing, but it is difficult to obtain densities greater than 90 pct of

Jan 1, 1963

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942