Search Documents

By Harry L. McNeill

The Selective Media Process was developed by the author in a laboratory provided by The Steams-Roger Manufacturing Co. It is the outcome of an investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Clifis Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7½-hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼-hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7½-hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). when treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is led to the washing plant the coarse

Jan 1, 1947

FREderick H. Davis, Electrical Engineer of the Westinghouse Electric and Manufacturing Co., in charge of the plant at Bodie, Cal. (communication to the Secretary): I beg to offer, to complete the information conveyed in Mr. Leggett's paper, the following report of tests of the electrical efficiency of the power-transmission he has described:

Jan 1, 1895

By Harry Morgan

ONE of the direct results of the increasing number of oil wells drilled to greater depths has been the development of new types of bits. These bits should resist the abrasive action of drilling and give the greatest footage before bit changes become necessary on account of dulled cutting edges. The loss of drilling time caused by changing bits becomes more important as the well becomes deeper, because the whole drill pipe must be unscrewed to make; each change. Under ordinary conditions the change takes: 2 1/2 hr. for round trip at 4000 ft., 3 hr. for round trip at 5000 ft., 4 hr. for round trip at 6000 ft., 5 hr. for round trip at 7000 ft. In other words, the time to change a stand of drill pipe (90 ft.) varies from 1 2/3 min. at 4000 ft. to 23 min. at 8000 ft. In general, the formation in the deeper zones is harder and dulls bits more quickly than the formations nearer the surface, therefore even a small increase of hole drilled per bit will decrease costs and increase speed of drilling.

Jan 1, 1929

By B. B. Cox

The Iraq Petroleum Company, Ltd. continued its systematic exploration and exploitation of the Kirkuk field on a unitized basis. Pressures, gas-oil ratios, oil-water level and oil-gas level remained satisfactory. All wells were produced by flowing and more than two-thirds of the crude was stabilized. The only exports from Iraq during 1937 were from the Kirkuk field. Mosul Oilfields, Ltd., through its operating subsidiary, the British Oil Development Company, Ltd., inaugurated an exploratory program to find lighter oil than the heavy, black, sulphurous reserve proved in the Qaiyarah-Najmah-Jawan-Qasab field. Deeper drilling in this field found a small reserve of 17" to 19" A.P.I. black sulphurous oil in the Pilsner (Upper Cretaceous). Ten structures outside the proved field were tested or were under test at the end of the year. In spite of this intensive program no reserve of lighter oil was discovered. The reserve at Qaiyarah-Najmah-Jawan-Qasab averages 16" A.P.I. with 6+ per cent sulphur from the "continuous limestone" (Lower Miocene, Oligocene, Middle Eocene) and from the Pilsner (Upper Cretaceous). The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., conducted the normal exploitation of its Naft Khaneh oil field and supplied the local Iraq market requirements. Slightly more than 31,600,000 bbl. of crude was produced in Iraq during 1937. The following table gives the total crude produced by the I.P.C. for export during the last four years. Year 42-gallon BarreL Increase over Preceding Year 1934 7,096,669 1935 27,014,904 19,918,235 1936 29,521,053 2,506,149 1937 31,171,476 1,650,423 " Converted at an average of 7.6 bbl. per ton. Published by permission of the Near East Development Corporation. Manuscript received at the office of the Institute March 11, 1938. * Geologist, Socony-Vacuum Oil Co., Inc., New York, N. Y.

Jan 1, 1938

By Robert R. Brookshire

Brush plating has been thought of by many as black magic bordering on alchemy. Actually it is a science that uses both electro-chemical and mechanical engineering skills and technology. We are not sure when brush plating was first used or by whom. I do know that many times when we would put in for patents on things we thought of as new and innovative, we would find that someone had done it many years before. It took World War I1 to get brush plating off and running. Now at this point, someone may be asking just what is brush plating? And why are we plating brushes? One way of describing what brush plating is, is by telling what it is not such as tankless plating. Brush plating-is an electro deposition of an electro-platable element or alloy onto a conductive surface. To do this a source of direct current is required; this can vary widely. I prefer stepless voltage control from 0-35 volts with a capacity depending on the size job to be done. This can vary up to 500 amps for normal applications. In one case we have used 7500 amps.. In the beginning a brush was actually used with a wire in the middle of the bristles and a jelly-like paste made up from tank plating solutions. The bristles were saturated with the gunk and the spot to be plated was muddled with the concoction at a potential which was the same as the applied tank Voltage. Metal was deposited but only thin coats were achieved. Today we use graphite wrapped or covered with cotton to form a Q-tip type anode. By using graphite rather than a specific metal we are able to either plate, de-plate or strip, electro- mill, electropolish, or anodize--all with the same equipment. Only the electrolyte needs to be changed.

Jan 1, 1984

By B. Das, V. Hucka

Two different types of filtration methods for in-situ gasification of coal are described. The different factors, i.e., geological, technological, and others, which affect in-situ gasification are given. The layout and operation of filtration methods of in-situ gasification are described in detail. The results of a case history are described.

Jan 1, 1977

By S. J. Rothman, A. L. Harkness, L. T. Lloyd

Self-diffusion in Y uranium has been measured using U235 as the tracer isotope. The diffusion coefficient fits an Arrhenius-type equation D = 2.33 x 10 -3 exp (- 28,5000/RT) cm2/sec The values of Do and Q are unusually low and are not consistent with the values expected from theories based on a simple vacancy mechanism of diffusion. CYLINDRICAL samples, 1 cm in diam and 1/2 to 1 cm long, were prepared from high-purity uranium containing 0.0343 pct u235, Table I. The samples were water quenched from 690°C (the a-ß transformation is at 668°C) to remove preferred orientation, and annealed at 450 "C to minimize residual stresses. One end of each cylinder was polished on a 1-µ diamond lap and electropolished in a phosphoric acid solution. After a final cleaning by cathodic sputtering, a 1- to 3-µ thick layer of the tracer isotope, uranium containing 93 pct u235, was sputtered onto the sample.' To prevent contamination during the diffusion anneal, the diffusion couples were placed in a tantalum cup and covered with another piece of uranium, and the whole assembly was sealed off in an evacuated quartz tube. Annealing temperatures were constant within +2.0°C. The samples were heated and cooled slowly between room temperature and the ß-? transformation (774°C) in order to minimize distortion of the sample surface that might arise from aniso-tropic thermal expansion and density changes during phase transformations. After machining off 1/16 in. from the radius to

Jan 1, 1961

By Joseph E. Pogue

THAT the domestic consumption of gasoline displays a marked seasonal variation, with a low in the winter and a high in the summer, is well known. It is logical to expect that the nature of the variation has itself been undergoing a change as a result of improvement in roads, general employment of closed cars; and growth of mass haulage; but so far as I am aware the change in seasonal variation has never been investigated and measured. It is the purpose of this paper to present the method and results of such an investigation undertaken as a contribution to the technique of planning operating schedules now so prominent in connection with the functioning of the industry under a Federal quota system. For the method employed I am in-debted to the suggestions and help of Frederick R. Macaulay', who kindly looked over the work sheets; and credit is due Barnabas Bryan, Jr., for assisting in the computations and the graphic work. Ideas for the approach to the problem were also derived from an article by Aryness Joy, and Woodulief Thomas of the Division of Research and Statistics of the Federal Reserve Board*-.

Jan 1, 1934

By G. H., Wigton

THE present milling operations of the Chief Consolidated Mining Co. consist- of flotation of oxidized minerals from siliceous ores of the Tintic Mining district, Utah. As the lead, silver, and gold minerals that give the ores economic value are almost entirely oxidized; their successful flotation has necessitated the solution of many new problems. Laboratory effort resulted in the selection of a, natural float for the oxidized minerals. 'By "natural float," I mean that no reagent was added to produce a sulfide film on the osidized minerals before or while subjecting them to flotation operations. As compared to methods involving sulfide filming, the natural float was selected because it promised successful treatment of a larger variety, of ores without change in quantity or kind of reagents, as well as a better economic balance between metal recovery and concentration ratio. In explanation, I can, state that with sulfide filming, the efficiency of the method decreases rapidly with increase of hydrated, iron osides in the ore, whereas with the natural float the same effect has not been noted. Evidence shows that although sulfidizing can produce greater metal recoveries, it yields a concentrate so much lower in grade that no advantage results.

Jan 1, 1928

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By R. B. Mears, E. H. Dix, R. H. Brown

In the Institute of Metals Division Lecture of 1940, E. H. Dix, J~.(I)~ discussed the acceleration of the rate of corrosion by high constant stresses. Experimental data obtained on this subject at the Aluminum Research Laboratories and a theory compatible with these facts were included in that lecture. The present paper contains data and ideas subsequently developed at the Aluminum Research Laboratories. Dix pointed out that in order for acceleration of corrosion by constant stress to occur: (1) There must exist in the alloy a susceptibility to selective corrosion along more or less continuous paths, as for in- stance at grain boundaries, and (2) There must exist a condition of high stress acting in a direction tending to pull the metal apart along these continuous paths. Acceleration of corrosion rate by stress is not confined to any one alloy system. Table I lists some of the metals and alloys and some of the corroding environments in which acceleration of corrosion by stress was sufficient to cause cracking (stress- corrosion cracking). It will be noted that the variety of alloys in which stress-corrosion cracking has occurred is rather large. Also, it will be observed that

Jan 1, 1945

By AIME AIME

AN unusually interesting meeting devoted to the discussion of the ways and means of improving coal mining practice, through the larger use of machinery underground, was held in the Auditorium of the Engineering Societies Building on March 11. The meeting was organized by the Materials Handling Division of the A. S. M. E. and held under the auspices of the Metropolitan Section of that Society and the National Coal Association. The New York Section of the A. I. M. E., which had been invited to participate, found itself unable to do so formally because of a conflicting date for its March meeting but informally did its part to aasure the success of the meeting. As a result of the discussion at and preceding the meeting, the National Coal Association, through Walter Barnum, chairman of its research committee, has asked the A. S. M. E. and A. I. M. E. to join the Association in a study of the present problems of the bituminous coal industry. Messrs. Harry L. Gandy, Calvin W. Rice and H. Foster Bain have been selected to act as a committee which shall develop plans for a joint program.

Jan 1, 1926

By J. J. K. Daemen, C. Fairhurst

Introduction The stress field around a supported tunnel can be considered as being composed of: i) the virgin (pre-mining) stress in the rock ii) the (elastic) change in this stress field caused by creating the opening iii) the (time-dependent ) change in the stress field produced by (i) and (ii) as a section of the rock breaks up iv) the (time-dependent) influence of the stress build-up in the support. Several authors have examined the conditions necessary to produce static equilibrium between the support, the rock, and the regional (in-situ) stress field. The analysis used by Labasse (1) is typical. Consider a circular tunnel radius R in a hydrostatic stress field (P), and a radial pressure pi exerted by the support. According to Labasse, the radius ‘b’ to which the rock will break* for a given support pressure, pi, can be calculated from: - the equilibrium equation: [ ] As a zone of broken rock develops around the opening, the stress circle for a point on the elastic-broken rock boundary moves to the right in the Mohr diagram until the radial stress in the broken zone s equal to the radial stress in the elastic zone.

Jan 1, 1971

By W. R. Clough, M. E. Shank

IT has been noted in a study of the flow and fracture of nodular cast iron under biaxial stress conditions (complete results of which will be published later) that when this metal is subjected to stress it may undergo a striking density change. Such behavior was first determined by strain gage measurements made on tensile test specimens, and has since been substantiated by other types of measurement. The chemical analyses and mechanical properties of several nodular irons to be discussed here are given in Tables I and 11. Tensile data for iron A was obtained from a hollow cylindrical combined stress specimen of the same dimension as those used by L. F. Coffin, Jr.1 in his investigation of gray iron properties. Standard 0.505 in. solid tensile-test bars were used for irons B and C. On each specimen type, A-8 wire resistance strain gages were used—two diametrically opposing gages in the axial direction, two in the tangential or hoop direction. By subtracting elastic strains from the measured strains, the plastic strains could be calculated. By assuming that radial and tangential strains are numerically equal, a measure of permanent volume change can be obtained by summing the plastic strains. This appears to be a good assumption, since the metal either fractured, iron A, or readings were discontinued, irons B and C, long before necking took place. This calculated variation of volume increase with stress is given for irons A and B in Fig. 1. Data for iron C is almost identical with that for iron B. The volume change indicated by Fig. 1 has been substantiated by a more direct type of density measurement. A method developed by S. G. Fletcher and' Morris Cohen,' and completely described in the discussion of their article, has been used. The accuracy of specific volume measurement has been estimated as 0.00002 cu cm per gram. Essentially the method consists of weighing a sample in air and then immersed in water. Measurements were made before and after straining the material. The results shown in Table I11 were obtained by means of half-size (0.252 in. diameter, 1 in. gage length, 3/8-16 threads) tensile specimens. Initial measurements were made on the whole specimen before stressing. After stress-

Jan 1, 1955

By W. J. Loring

It is proposed to describe in this paper as accurately as possible the present practice at the Utica mills, of which I am superintendent. The Utica Company operates three mills, the Madison (40 stamps), the Utica (60 stamps), and the Stickle (60 stamps). My description will be based on the last-named, in which I have experimented more than in either of the other two; but the practice is the same, under the same management, in all three. Everything is run by water-power, under about 420 feet fall at the Utica mill, and 425 feet at the Stickle mill, giving a pressure of about 185 pounds to the square inch. The Madison mill is situated about three-quarters of a mile below the Utica and Stickle mills, and has only some 100 feet fall from one place, and 38 feet fall from the other. The water that runs the Utica and Stickle mills, and all machinery connected with the corresponding mines, is conveyed through ditch and pipe to the Madison mine and mill, where it develops power for the air-compressor and the 40-stamp mill. The mill is run by a

Jan 1, 1899

By David T. Day

In the summer of 1898, a demand suddenly arose for commercial quantities of the element osmium. At least half a ton was wanted for the manufacture of a new incandescent light. This led the writer to examine localities where platinum had been reported, in order to determine whether osmiridium mas contained in the crude platinum. With the co-operation of the concern most interested, the Welsbach Light Company, and in company with its President, Col. William E. Barrows, I visited most of the leading American localities where platinum has been obtained. I also wrote to every available placer-mine in the West for samples of the heaviest sands, in order to test them for platinum. The results of this inquiry are given in the present paper. Distribution. The notices of the occurrence of platinum in this country given in scientific journals include two interesting observa tions in the East. One concerns a nugget described by Peter Collier of Washington, D. C.,* and said to have been found on land adjacent to the village of Plattsburgh, N. Y., which weighed 104.4 grammes, and contained sufficient chromite to reduce the specific gravity from 17.35 for the heaviest portion to

Jan 1, 1901

By J. M. Toguri, H. Flood

The application of the mass action law to the thermodynamic treatment of metal-slag equilibria is discussed. The consideration of the reactions essentially as ionic exchange equilibria is shown to be both an advantage and an aid for the elucidation of the theoretical treatment. This is illustrated by several examples. In general two different methods of application of the mass action law to metal-slag equilibria have been used by different groups of investigators. These could be called the oxide reaction and the ionic reaction approach respectively. At the recent discussion in the metallurgical section of the I.U.P.A.C. Congress in Montreal, 1961,' divergent opinions prevailed regarding the most rational way of applying the mass action law to metal-slag equilibria. This question is of fundamental importance in the treatment and understanding of theoretical chemical metallurgy. Consequently, the following is an attempt to contribute towards its clarification. As an example, the distribution of iron and manganese between molten iron and slag will be considered. I) THE OXIDE EXCHANGE REACTION APPROACH The equilibrium between iron and manganese between molten iron and slag is frequently formulated as an oxide metal exchange reaction as follows:

Jan 1, 1963

By John D. Morgan

Prior to World War I there was no Government stockpiling program. Prior to World War I1 relatively few items were included in Government stockpiling and the start of that war found most objectives for even these few materials far from complete. Profiting from the experience of materials shortages in two wars, Congress in 1946 passed the Strategic and Critical Materials Stock Piling Act, which stated that it is the policy to decrease and prevent wherever possible a dangerous and costly dependence of the U. S. upon foreign nations for supplies of strategic and critical materials in times of national emergency. However, as of mid-1950 few stockpile objectives had been achieved. Shortly after the start of the Korean War it was obvious that in the absence of adequate stockpiles, the defense program could not be successfully carried out without broad authority to expand supplies of strategic and critical metals and minerals and at the same time to channel limited supplies of these materials to essential defense purposes. Accordingly, in September 1950 Congress passed the Defense Production Act, which provided broad powers for allocating materials and for making arrangements, including financial, to expand supplies.

Nov 1, 1955

By O. L. Culberson, J. J. McKetta

Experimental and smoothed data are presented for the solubility of methane in water for temperatures of 77, 100, 160. 220. 280, and 340°F at prejsures to 10.000 psia. The minimum solubility phenomenon exists within this temperature range to pressures of 10.000 psia. INTRODUCTION The study of hydrocarhon-water systems has been extended to the determination of the solubility of methane in water at pressures to 10.000 psia. The experimental apparatus, and the technique. are the same as that previously reported.' - In the determination of the solubility of methane in water, only two phases were present at temperatures between 100 and 340°F. these being the vapor phase and the water-rich. liquid phase. The determinations involved the agitation of methane and water in an equilibrium cell. withdrawal of a sample from the liquid phase, and the analysis of the sample. The experimental value; determined in this manner are pre9ented in Table I and in Fig. 1. Since experimental and analytical techniques have improved since the initial experiments with this equipment, it was decided to repeat the 77°F isotherm determinations.' Fig. I shows that the individual results for this isotherm are much

Jan 1, 1951