Search Documents

By John Birkinbine

IN the spring of 1878 the Pine Grove Furnace, located in Cumberland County, Pa., was blown in after lying idle for several years. The furnace was constructed in 1770, and for over a century it has been in almost continual operation. The plant consisted in 1877, when the writer was first called there, of a stone stack 32 feet in height, inclosing a shaft and boshes, the latter being 8 feet in diameter. The blast was supplied by two wooden blowing-tubs discharging into a third, having a floating piston sustaining a box weighted to give the desired pressure, the power being furnished by a waterwheel. A small 18-pipe hot-blast stove heated the blast. The furnace was remodelled during the winter of '77-78, and a Weimer blowing-engine with a blowing-tub 5 feet in diameter and 2 feet stroke, and the necessary boilers, were substituted for the wooden tubs and water-wheel. The stack was raised and enlarged, and provided with a bell and hopper having a central drop. Water dam and tymp were added, and general repairs were made. The hot oven, however, was riot increased. The furnace had always been operated with charcoal as fuel, and its reconstruction was made with a view to continue the use of charcoal, but provision was made for ample blowing capacity should other fuels at any time be employed. Although liberal arrangements had been made in cutting wood, the stock of charcoal supplied in 1878 was insufficient for the increased requirements of the remodelled plant, and notwithstanding the purchase of some 80,000 bushels from an adjacent idle furnace, there was riot enough to keep the furnace in constant blast until a new supply could be obtained, particularly as the season was unusually backward. Instead of following the established precedent of many charcoal furnace managers, i. e., blow out every February, it was determined to continue in blast, using coke as fuel. Accordingly, when the charcoal stock was exhausted, on March 22d, 1879, Connellsville coke was substituted, the change of fuel being made at once; that is, the coke charges followed immediately upon the last charcoal charges. After working a few days,-the strike in the Connellsville coke region cut off the supply, and anthracite coal was obtained, a mixture of the two fuels being employed. The strike continuing,

Jan 1, 1880

By Lewis A. Delano, Harold Rabling

It has been generally recognized that, owing to the extreme friability of galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth re-treating today. Investigations of the work of the Hancock jig on the Bonne Terre ore have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average for all conditions and grades of ore will be between 0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increascd smelting charges due to a greater amount of slime galena will be counterbalanced by the lower operating cost, increased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various Bow sheets, and to calculate the economics of the problem with great accuracy. Concentration Problem The ore occurs as widely scattered deposits of galena disseminated through limestone; it has a specific gravity of 2.8 and the following composition: Pb, 4.00 per cent.; Fe, 3.00 per cent.; Zn, 0.32 per cent.; S, 3.10 per cent.; MnO2, 0.73 per cent.; SiO2, 4.20 per cent.; Al2O3, 3.20 per cent ; CaO, 28.60 per cent.; MgO, 16.85 per cent.; CO2, 36.00 per

Jan 1, 1922

By David K. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are w-asted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Shipments of pyrite from coal mines during 1941 were reported as follows: Illinois -The Midland Electric Coal Corp., Henry County, shipped 12,026 long tons containing 46 pct sulphur, at its Atkinson preparation plant. Indiana—The Snow Hill Coal Corp. produced pyrite from its Talleydalc preparation plant in Vigo County. Kansas—The Mineral Products Co. produced 3902 long tons of pyrite containing 44 pct of sulphur from picking table and washery refuse. Specifications for coal pyrite for acid manufacture rangc from 5 to 8 pct maximum carhon limit, and 42 to 45 pct minimum sulphur limit. Where flash roasting is practiced, the pyrite must be minus 100-mesh. Most companies give no size specifications. One company specifies 20- mesh or finer. Impurities in pyrite other than carbon may limit its use—for instance, arsenic, probably as arseno pyrite-—even though a concentrate can be made complying with specifications otherwise. Pyrite-recovery Plants Bradford breakers and picking tables may be used to make a marketable product where the pyrite occurs largely in sizes coarser than about I in. To make a grade of concentrate acceptable to sulphuric-acid plants the pyrite must break freely from the accompanying coal and slate, which is a rare condition to find. Most pyrite occurring in coal beds requires crushing and an abrasive type of grinding to free it of entwined coal and slate, followed by mechanical concentration by jigs, tables or other concentrating devices suitable for heavy ores, to make a satisfactory concentrate. At the Snow Hill Coal Corporation's plant in Indiana and at the Midland Electric Corporation's plant at Xtkinson, Ill., the final concentrate is made by a mechanical jig. The most recent and complete mill for concentrating pyritc from coal-mine refuse is that of the Mineral Products Co. at West Mineral, Kans., in which jigs and tables are used. Many regrinds and recirculations of products are necessary to get a concentrate of uniform grade. Trends On the whole, the economics of recovering pyritc from coal is not favorable. Cer-

Jan 1, 1948

By David K. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are w-asted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Shipments of pyrite from coal mines during 1941 were reported as follows: Illinois -The Midland Electric Coal Corp., Henry County, shipped 12,026 long tons containing 46 pct sulphur, at its Atkinson preparation plant. Indiana—The Snow Hill Coal Corp. produced pyrite from its Talleydalc preparation plant in Vigo County. Kansas—The Mineral Products Co. produced 3902 long tons of pyrite containing 44 pct of sulphur from picking table and washery refuse. Specifications for coal pyrite for acid manufacture rangc from 5 to 8 pct maximum carhon limit, and 42 to 45 pct minimum sulphur limit. Where flash roasting is practiced, the pyrite must be minus 100-mesh. Most companies give no size specifications. One company specifies 20- mesh or finer. Impurities in pyrite other than carbon may limit its use—for instance, arsenic, probably as arseno pyrite-—even though a concentrate can be made complying with specifications otherwise. Pyrite-recovery Plants Bradford breakers and picking tables may be used to make a marketable product where the pyrite occurs largely in sizes coarser than about I in. To make a grade of concentrate acceptable to sulphuric-acid plants the pyrite must break freely from the accompanying coal and slate, which is a rare condition to find. Most pyrite occurring in coal beds requires crushing and an abrasive type of grinding to free it of entwined coal and slate, followed by mechanical concentration by jigs, tables or other concentrating devices suitable for heavy ores, to make a satisfactory concentrate. At the Snow Hill Coal Corporation's plant in Indiana and at the Midland Electric Corporation's plant at Xtkinson, Ill., the final concentrate is made by a mechanical jig. The most recent and complete mill for concentrating pyritc from coal-mine refuse is that of the Mineral Products Co. at West Mineral, Kans., in which jigs and tables are used. Many regrinds and recirculations of products are necessary to get a concentrate of uniform grade. Trends On the whole, the economics of recovering pyritc from coal is not favorable. Cer-

Jan 1, 1948

By D. E. Furman

The thermal coefficients of linear expansion for several stainless steels have been determined over the temperature range from —300° to 1000°F. The steels studied include types 301, 304, 316, 347, 310 and 330. This wide selection of compositions allows an insight into the effects of austenite stability and alloy content on the expansion characteristics. THE recent increased use of materials in low temperature applications has created a field for which the properties of austenitic iron, chromium, nickel alloys are particularly suited. Tensile and impact values of stainless steels at subzero temperatures have been made available in the technical literature but, as yet, little information has been published with respect to expansion characteristics. In order to supply this need, a study was made of several of the more common compositions. Those selected were types 301, 304, 316, 347, 310 and 330 stainless steel. Both the mean and instantaneous coefficients of linear expansion were determined over the temperature range from —300°F to 1000°F. Procedure The materials used were commercial grades with the exception of type 301 which was made in a 10# high frequency furnace. The compositions are listed in table I. All steels were given an anneal at 1950°F for 30 min and water quenched prior to machining the expansion specimens. Expansion readings were taken on specimens 0.250 in. in diam by 4.000 in. long with a fused quartz tube expansion apparatus similar to that described by Hidnert and Souder.1 Temperature measurements were made with a chromel-alurnel thermocouple calibrated for use at subzero temperatures. A bath of propane was used for temperatures from —300° to —100°F and one of alcohol from —100°F to room temperature. These baths were contained in large mouthed Dewar flasks and cooled to the desired temperature levels by passing liquid nitrogen through glass cooling coils placed in the flasks. The baths were stirred constantly for temperature equalization and were heated by immersing metal rods which were replaced frequently enough to give a heating rate of approximately 150°F per hr. A resistance wound furnace was used for heating from room temperature to 1000°F and throughout this range rates of about 450°F per hr were maintained. The furnace was designed so that the temperature gradient over the specimen was within 5°F. In most instances, the expansion readings were taken during heating from —300° to +300°F at

Jan 1, 1951

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By W. Rostoker, A. S. Yamamoto, K. Anderko

ALTHOUGH the corrosion resistance of magnesium and its alloys is closely related to iron content, there has been no direct measurement of the solid solubility of iron in magnesium. Bulian and Fahrenhors;1 and Mitchel]2 agree that pure iron or a limited terminal solid solution crystallizes from the Mg-rich liquid. For this reason a magnetic-moment method was selected to estimate that portion of the total iron content which is not in solid solution. Since iron in solid solution in magnesium cannot contribute to ferromagnetism, the difference between chemical and magnetic-iron analyses should yield the solid solubility. By experimentation it was found that the melting of pure sublimed magnesium (99.995 wt pet purity) in Armco-iron crucibles at about 800°C is a convenient way to introduce small amounts of iron. Melts retained 5, 10 and 20 min at 800°C analyzed 0.003,, 0.005,, and 0.018 & 0.001 weight pet Fe, respectively, after being stirred, heated to 850°C, and cast into graphite molds. The as-cast alloys were pickled in acid (dilute HC1 + HNO3), annealed at 600°C for 3 days, scalped on a lathe to remove the pitted surface, pickled again, extruded at about 100°C to 3-mm wire, reannealed 41/2 days at 500°C, and water-quenched. The specimens were again scalped, pickled, and used both for chemical and for magnetic analysis. Most of the precautions described were intended to prevent iron pickup by contact with tools or superficial iron enrichment by volatilization of magnesium during heat-treatment. It is believed that the specimens ultimately used for test were homogeneous and characteristic of phase equilibria at 500°C. Magnetic Analyses A susceptibility apparatus of the Curie type was used for magnetic analyses. Field strengths of up to 10,400 oersteds could be generated. By this method, an analytical balance measures the force of attraction which a calibrated magnetic field exerts on a suspended specimen. The force equation is as follows f/m = M dh/dy where f/m = force per unit mass of sample M = magnetic moment per unit mass dH/dy = magnetic field gradient The dH/dy characteristic of the instrument is determined by the use of a standard palladium sample, and the calibration is made independently for all values of H. Since a large finite field is required to saturate an assembly of ferromagnets, it is necessary to measure the apparent magnetic moment for increasing steps of H until a saturation value is obtained. The percentage of iron in the sample as free ferromagnetic iron may then be computed simply C= 100 (M1/M1) where C = percent content of undissolved iron in sample M1 = saturation magnetic moment of sample per unit mass M1 = saturation magnetic moment of iron per unit mass taken as 217 emu-cm per gm There is no serious difficulty in applying this method except for the unusual magnetic behavior of very fine particles of ferromagnetic substances. It has been found and is the basis for a widely accepted theory that with sufficient subdivision, the magnetic fields required to saturate and the coercive force after saturation rise to exceedingly high values. Recent work on precipitates of Fe and Co from copper solid solutions8 showed that about 5000 oersteds were necessary to approach saturation. The magnetic moments as a function of field strength measured in the present investigation are listed in Table I. Only the 0.018 wt pet Fe alloy yielded a magnetization curve with a fairly well-defined saturation plateau at 3.76x10 -2 emu-cm/ gm. This corresponds to 0.017 & 0.001 wt pet Fe in the alloy. This indicates that the solid solubility must be of the order of 0.001 wt pet Fe. The magnetic-moment data of the other two alloys are badly scattered, indicating that the amount of ferromagnetic iron in these samples is so low that the magnetic forces acting on them cannot be measured accurately by the analytical balance used. Nevertheless, the fact that even the 0.003, wt pet Fe alloy shows ferromagnetism indicates that the solid solubility must be below that value. Acknowledgment This work was sponsored by the Pitman-Dunn Laboratory of Frankford Arsenal, Philadelphia, Pa. The support and permission to publish are gratefully acknowledged. References W. Bulian and E. Fahrenhorst: Zeic. Metallkunde, 1942, vol. 34, pp. 116-170. 2 D. W. Mitchell: AIME Transactions, 1948, vol. 175, pp. 570-578. 3 G. Bate, D. Schofield, and W. Sucksmith: Philosophical Magnsine, 1955, vol. 46, pp. 621-631.

Jan 1, 1959

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.&apos; It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,&apos; by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

By C. E. Taylor, L. V. Fegan

With on-stream electrical-resistance measurement as a basis, Bethlehem Steel developed a system for the completely automatic control of moisture in the feed to pelletizing. This system was later successfully adapted to the sintering process, with automatic control of moisture serving to maintain the air permeability required for effective burnthrough. Control of moisture content is an important factor in the agglomeration processes by which iron ores are converted into either pellets or sinter for use in blast furnace burdens. In both pelletizing and sintering the iron ore feed must be mixed with the proper amount of water so that capillary attraction and surface tension forces can be utilized to cause the ore particles to coalesce and form larger agglomerates. The success or failure of the entire pelletizing or sintering process depends on maintaining the proper moisture. Therefore, continuous automatic control of moisture is one of the conditions for the automation and optimum use of both pelletizing and sintering processes. In pelletizing, variation in moisture can cause ball size to change and is a common cause of cycling which results in a fluctuating feed to induration. Excessive moisture can cause lumps to form at the cutter bar and contributes to the formation of buildup on the green pellet screens. Green pellets with excess moisture deform and reduce bed permeability. In sintering, accurate control of moisture is also important because moisture must be within the limits that give the bed the required permeability for good burnthrough. In response to these problems, a moisture meter, based on the principle of electrical resistance measurement, was developed. This moisture meter has been a key factor in the development of systems for providing uniform feed of concentrates in most of Bethlehem&apos;s pelletizing and sintering plants. The automatic moisture control system for pelletizing was successfully plant-tested and resulted in the following: (1) Control of moisture in the green pellets to +0.2%. (2) Up to 50% reduction of bentonite consumption. (3) Control of unscreened green pellets so that 85% of the furnace product at Cornwall was within the size range of -5/8 +3/8 in. (4) Improved quality of product with a tumble test of 94 and a "Q" index of 90 as the result of feeding a consistently uniform feed to a shaft furnace. In sintering, where sinter-mix temperature change and variable feed could cause errors in moisture measurement, the system was designed to maintain the correct moisture under virtually all plant operating conditions. It was successfully plant-tested and is now in use in most of Bethlehem&apos;s sintering plants. The system achieves: (1) Control of moisture within the desired limits for optimum production. (2) Continuous measurement and control of moisture even with intermittent feeding of mix, so that attention by the operator is seldom required. The two automatic control systems provide smoother startup, minimize upsets and contribute to the consistent control of process variables in pelletizing and sintering. MOISTURE-CONTROL SYSTEM FOR PELLETIZING Fig. 1 shows the general arrangement of the system for automatic control of moisture in pelletizing.1 In this system a bin level controller, using a single probe which regulates filter speed, maintains a uniform low concentrate level in the bin.&apos; The moisture meter, comprised of an analyzer and control components, continuously measures the moisture in the bed and adds water to adjust to the desired level. The meter is placed in an open-loop (feed-forward) control, i.e., water addition occurs downstream from the probes. Filter vacuum must be set so as to produce a filtercake moisture which is below the optimum for pelletizing. Bentonite is added after the

Jan 1, 1969

By N. J. Grant, C. C. Wang

The Ti-Cr-O ternary system has been studied in detail near the titanium-rich corner within the limits of 10 wt pct 0, and 20 wt pct Cr. Studies were extended, but not in detail, to the region beyond 25 wt pct 0, (50 atomic pct) and 62 wt pct Cr (60 atomic pct). Four isothermal sections at 1400°, 1200°, 1000°, and 800°C are presented as well as two vertical sections at 1 and 2 wt pct 02. DURING the last decade much interest has been shown in the development of high strength titanium alloys for high temperature and corrosion resistant applications. Extensive research is being carried out at present, as the current literature indicates, in order to study the properties of titanium and to develop improved alloys. Two of the important alloying elements in commercial titanium alloys are chromium and oxygen and it would be desirable to know their combined influence upon titanium. For this purpose the present work was carried out to investigate the titanium-rich corner of the ternary system TiICr-0. The binary systems Ti-Cr and Ti-0 have been published recently. The Ti-Cr system was studied by several investigators " and their results are in close agreement. The eutectoid decomposition of the B phase has been shown to be extremely sluggish. TiCr, was the only intermetallic compound found in this binary system and was formed at 1350°C by a transformation from the p phase. TiCr? was established as the cubic C 15 (MgCu,) type of structure with 24 atoms per unit cell and was designated as the y phase. This terminology will be adopted in the present work. There was disagreement about the actual composition of this compound among the several investigators, although it is evident from their data that the compound probably has a solubility range of about 2 to 3 pct and is in the vicinity of 65 pct Cr. It has been indicated recently that a high temperature modification of this y phase (TiCr,) existed at a temperature above 1300°C." &apos; This high temperature modification was identified as a hexagonal C 14 (MgZn,) type of structure with 12 atoms per unit cell. The exact transformation temperature from the high temperature phase to the low temperature phase has not been established. A considerable hysteresis was observed and, due to the sluggishness of this transformation, the high temperature phase often co-existed with the low temperature phase at temperatures below 1300°C. A preliminary study of several Ti-0 compounds and the Ti-0 system had been carried out by Ehr-1ich."-"&apos; The most complete binary Ti-0 system was the one reported recently by Bumps, Kessler, and Hansen." The first intermediate phase found in the system was the 8 phase which formed by a peritec-toid reaction of the phases a and Ti0 at temperatures below 925 °C. This reaction is extremely sluggish. The structure of this 8 phase was tentatively identified by these authors as being tetragonal and the lattice constants were found as c,, - 6.645A, a,, = 5.333A and c/a = 1.246A. Experimental Procedure The raw materials used for this investigation were TiO,, electrolytic chromium, iodide titanium, and sponge titanium. The TiO, was in the form of powder of chemically pure grade (99.8 pct pure). The chemical analysis of the electrolytic chromium was: 0, 0.50 pct; Fe, 0.07; Cu, N, and C, 0.01; and Pb, 0.001. The oxygen in the chromium was calculated as part of the final oxygen content of the alloys. The alloys were prepared by the cold crucible method using a tungsten arc. The entire system was evacuated and flushed with purified helium three times and then filled with helium. Each alloy was melted, turned over, and remelted at least four times to insure homogeneity. The total melting time was generally from 6 to 10 min. A master alloy of 25 pct 0,-75 pct Ti was prepared to facilitate alloying by melting compacts of TiOl powder with either iodide or sponge titanium, yielding the compound TiO. It was found necessary to bake the TiO, powder compact at about 150°C to remove adsorbed moisture. This was done to prevent the disintegration and spattering of the compact when the arc was struck. TiO, powder dissolved quite readily into the melt and no other trouble was encountered.

Jan 1, 1955

By Ronald D. Hill, Janet L. Auerbach

It is estimated that the mining industry generates over 2.1 petrograms per year of solid waste. These wastes are overburden, waste rock, low grade ore, concentrate (tailing), sludges from treatment facilities and wastes from support facilities. Concentrate wastes present the greatest environmental problem. Three recent federal laws impact the disposal of waste from mining: Resource Conservation and Recovery Act of 1976 (RCRA), Surface Mining Control and Reclamation Act of 1977, and Uranium Mill Tailings Radiation Control Act of 1978. RCRA specified a special study on mining waste which was to include an analysis of: (1) sources and volumes of waste produced, (2) present disposal practices, (3) potential dangers to health and the environment, (4) alternate disposal methods, (5) cost of disposal, and (6) potential for use of waste.

Jan 1, 1980

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

Arrangements have been completed in New York whereby the re- sources of The Engineering Foundation, under the auspices of the four principal national engineering societies, are placed at the disposal of the National Research Council, which was appointed by the National Academy of Sciences* at the request of President Wilson. The object of the Council is to coordinate the scientific research work of the country in order to secure efficiency in the solution of the problems of war and peace. The Council was without funds until The Engineering Foundation, established to further scientific and engineering research, offered to place its resources at the Council&apos;s disposal, including the services of its secretary, Dr. Cary T. Hutchinson, to act as-secretary of the Council. The offer was accepted and plans for immediate activities have been placed in the hands of an executive committee. In indicating how thoroughly, every branch bf science and engineering is represented, Dr. George E. Hale, Director of the Mt. Wilson Solar Observatory, and Chairman of the Council, when he was in New York attending to the details of the arrangement, called attention to the personnel of the body, saying that it is the purpose to enlist the cooperation, in the solution of our industrial and military problems of a scientific character, of every possible established agency. Medicine, for example, is represented on the Council by Dr. William H. Welch, President of the National Academy of Sciences, Brigadier General William C. Gorgas, , Surgeon Crenera.1 of the United States Army, Dr. Simon Flexner, Director of the Rockefeller Medical Institute, and Dr. Victor C. Vaughan, Past President of the American Medical Society; biological science by Dr. Edwin G. Conklin, Professor of Zoology, Princeton University; chemistry by Dr. A. A. Noyes of Massachusetts Institute of Technology and Dr. L. H. Baekeland; physics by Dr. A. A. Michelson of the University of Chicago; and electricity by Professor M. I. Pupin, of Columbia University.

Jan 10, 1916

By B. J. Scheiner, A. G. Smelley

The Bureau of Mines, US Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. Infield tests, phosphate clay waste has been dewatered from a nominal 2.5% solids to greater than 20% solids. In other field tests, coal-clay waste has been dewatered from a nominal 3% solids to greater than 55% solids. In addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12% solids to 40% solids.

Jan 1, 1985

1. A passenger rickshaw in China. 2. A Pekin cart carrying coal, on dirt roads; the cost works out to 15 or 20 c. per ton-mile. 3. Coolie with wheelbarrow. This one has a small load, but barrow men carry ordinarily 250 lb., occasionally 400 if with a helper. He goes about 18 miles a day and the cost is about 25c. gold per ton-mile, though it varies widely. 4. Coolie delivering coal balls in Pekin. He carries about 65 lb. On some roads with a different arrangement a coolie carries 133 lb., making about one ton-kilometer per day. 5. Truck used by the Government Fuel Yard at Washington. Carries 71/2 tons in an hour as far as a barrow man carries 1/4 ton in a day.

Jan 8, 1928

INTERNAL The year 1976 was another outstanding year in the operation of the Institute and in the success of its varied activities. Total AIME membership reached 59,773 for a gain of. 6.4 percent. Total revenue increased to $5,111,2 10, up 22.4 percent, and balance sheet assets increased to $8,479,612, up 12.2 percent from the previous year. AIME and its constituent units conducted 30 technical meetings during the year, and attendance was up at most of them. Publications issued by the Constituent Societies continued a healthy growth. During the year 9 new local Sections were established, and at the end of the year the Institute had 150 Sections, with 19 of them overseas. Details on all of these operations are on pages 2 and 3 of this report.

Jan 4, 1977

By M. G. F. Söhnlein

In a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. + 20 8.0 40 36.5 + 60 9.0 + 80 10.5 + loo 5.5 4-150 1 4.5 -150 25.0 99.0 Loss 1.0 In the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.&apos; This remodeled classifier consists of a truncated pyramidal wooden hopper A with an attachment of cast iron

Jan 1, 1917