Search Documents

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS, * LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers' determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By Walter B. M. Davidson

Phosphorus is one of the elements having the widest distribu tion, and phosphoric acid plays an important part in the composition of the crust of the earth. It is allied in various chemical combina- tions with many bases, of which lime, alumina and iron are the most common. It is difficult to state in what chemical combination phosphoric acid predominates in the crust of the earth, for while phosphate of lime, as the mineral which is sought for and found in deposits of economic value is the most familiar, it is probable that the phosphates of alumina and iron are the most usual forms in which phosphoric acid exists in all soils not essentially calcareous. It has been shown by thousands of analyses that all fertile soils contain from a trace to 0.5 per cent. of phosphoric acid. All limestones, dolomites and chalks contain it in proportions which, though usually small, are large enough to make careful analysis necessary in the selection of limestone as flux for iron-smelting. It is generally Trenton limestones that are found best for this purpose, the more recent strata being more phosphatic. In some places phosphoric acid replaces carbonic acid, and the limestone or chalk becomes phos phatic to a large degree, or sometimes pure phosphate of lime. The waters of the ocean, from very early periods, have contained phosphoric acid. Different analyses show varying contents; it is asserted that some portions of the Gulf Stream are more phos phatic than the surrounding waters of the Atlantic. Many springs, usually from limestone regions, contain soluble phosphates in vary ing quantities. I think it safe to assert that phosphorus is nearly the most widely and evenly distributed element on the surface of the earth, and probably the most subdivided. This can be readily understood when the important part which phosphoric acid plays and has played in the vital cosmos is taken into consideration. Phosphorus was on the earth in gaseous, liquid or solid form before the dawn of life, and since then all animal and vegetable creation have combined with the

Jan 1, 1893

By Robert J. Anderson

DURing the past 5 years no subject has aroused more interest or received more attention among mill operators than flotation. One reason for this is, undoubtedly, the remarkable success of the process in Australia where that country has risen to the position of furnishing one-fifth of the world's supply of zinc. The plant of the Butte & Superior Copper Co., designed by James M. Hyde in 1912, was the first important large flotation plant in this country; other installations have been made since then with considerable frequency, particularly so in the last 2 years. Without going into complete detail, it may be safely said that although flotation is a highly successful commercial process, it is more or less on an empirical basis. Upon scanning the literature, it is found that the flotation investigations have, in the main, dealt with a solution of the problems which accrue to practise; until recently no attempt was made to remove the difficulties in the way of the formulation of a consistent and harmonious theory. Of late this phase of the work has been receiving considerable attention, particularly by the United States Bureau of Mines at its Salt Lake City station, by the Mellon Institute at Pittsburgh, by the General Engineering Co. at Salt Lake City, by many of the mining schools, and private individuals almost ad infinitum. There is, at present, an enormous amount of laboratory work being carried on in flotation research, and probably the time is not far away when a generally acceptable explanation of flotation phenomena can be set forth. However, at this time, it seems as though the current technology is befogged with a superabundance of contradictory evidence; this confusion can only be dispelled as time proceeds and the knowledge of the subject becomes more complete. Many phenomena are supposed to contribute to the flotation of minerals, whether in whole or in part is a mooted question. I shall only sketch roughly the present tendency of ideas and make no reference to the first early and crude notions which have little value other than histori-

Jan 1, 1917

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Herbert F. Miller

For a long time I have believed that the gas- and brick-costs of open-hearth furnaces using prodncer-gas could be greatly decreased by a change in the design of the port, which would materially reduce the first-cost of the furnace, the rebuilding-cost, and the repair-cost. The defects of the present type of such furnaces, which has clone duty for so many years, may be studied in Fig. 1, in which A A are the two air-uptakes, B is the gas-uptake, and C the end of the gas-port. In the present type of furnace, C is practically 011 the edge of the bath and therefore combustion begins to take place at that point, but has no effect until the gas passes from 5 to 10 ft. into the hearth. As the furnace grows older, C moves back by reason of the burning or falling down of the arch. The furnace reaches its highest efficiency when C has moved a certain distance, but is still near enough to the bath for the overhead layer of air to hold the gas down on the bath, and far enough back to permit combustion to take place at some distance from the bath. This latter fact means that the temperature is sufficient to melt steel at the edge of the port. From this time on, the furnace decreases in efficiency. What is the reason ? As C moves further hack, the gas is released from the gas-port at a point where there is little or no overhead layer of air. The result is that the gas floats along the roof, with the air mostly underneath it. Why the air does not stay over the gas is readily seen in Fig. 1. The lines of draft naturally run parallel to the length of the furnace. The air-uptakes being on the sides and the gas-port in the middle, most of the air will naturally be drawn along the sides of the furnace and the layer of air will be thinnest over the gas, where it is most needed.

Jan 1, 1914

By Pierre de P. E. M. Ricketts

HAVING had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

Jan 1, 1876

By L. E. Porter, H. P. Hassel

The state of California produced 310,-996,696 bbl. of oil and about 415,832,000 M cu. ft. of gas in 1944. Such oil production represented 18.5 per cent of the nation's production, as compared with 19 per cent in 1943 ,The tremendous demand placed upon the California fields is indicated by the monthly production in 1944, as follows: Month Barrels per Day Jan................... 809,262 Feb.................. 820,712 Mar.................. 824,592 .4pr ................. 829,973 May.................. 832,068 June.................. 846,038 July.................. 849,231 Aug.................. 858,932 Sept.................. 885,823 Oct................... 877,667 Nov.................. 876,613 Dec.................. 883,847 In all, 2100 wells in proved areas and 269 wildcats were drilled in California during the year 1944. At the end of the year, approximately 270 wells were drilling in the state, as compared with 156 wells at the same time in the preceding year. Nine new fields or new zone discoveries were made during the year, which, according to best estimates, will contribute some 77,000,000 bbl. of new reserves; in addition, the extensions of old fields will increase the new reserves about 165,000,000 bbl., or a combined total, through dis- coveries of new fields, zones, and extensions, of 242,000,000 bbl., offsetting to the extent of about 78 per cent the total oil produced during the year. Geographically, the reserves from these new field and zone discoveries and extensions are distributed as follows: Per Cent San Joaquin Valley........ 72 Coast Area............... 24 Los Angeles Basin Fields. . . 4 100 The state's reserves of crude oil at the end of the year have been estimated to be distributed as follows: The outstanding development project for the year was that of the United States Navy in the Naval Petroleum Reserve No. I, Elk Hills field. During the year, 115 wells were completed in this field, and at the close of the year an average of 19 strings of tools were drilling. This program is being jointly conducted by the Standard Oil Co. of California with the Navy and is designed to increase the production of Naval Petroleum Reserves from approxi-

Jan 1, 1945

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By R. W. Raymond

GEHEIMER BERGRATH Prof. Dr. HIERONYMUS THEODOR RICHTER, ex-Director of the Freiberg Mining Academy and Honorary Member of this Institute (to give him the full title, which nobody ever thought of using in his genial and unceremonious presence, and the whole of which I have omitted at the head of this notice, as adding nothing to the virtue and value of the man I knew), died on Sunday, September 25,1898. He was born in 1825 at Dresden, and in 1843, after some practical training in pharmacy, entered the Freiberg Mining Academy, where he devoted himself chiefly to metallurgy and metallurgical chemistry, under the guidance of the celebrated Plattner, whose masterly instruction in those arts, and also, especially, in assaying and the use of the blow-pipe, has been classic authority to the present day. In 1853, Richter was ap-

Jan 1, 1899

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By Edward Pesout

THE McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.1 EARLY PULVERIZING PLANT Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a finer product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. [ ] It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. 0-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1945

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,' Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships