Search Documents

By R. W. Raymond

I DESIRE to call the attention of the Institute briefly, and by no means in the way of an exhaustive description, to the interesting developments recently made on the east bank of the Hudson River, in the mining of spathic iron ores. The mines to which I refer are those of the Hudson River Spathic Iron Ore Company, situated at Oakhill on Hudson, Columbia County, N. Y., five or six miles from the city of Hudson, and opposite the town of Catskill. The ore occurs in beds, constituting apparently members of the stratified series of rocks on that side of the river, coursing nearly north and south, parallel with the river, and dipping east. The principal out- crops are presented in a range of low hills, about one mile from the river, along the crest, on the western face of which the stratum of spathic ore is more or less exposed. The length of the line in this range, along which, at various openings the ore has been discovered in profitable quantity, is about two miles. To the northward, the hills are somewhat higher, and the stratification may possibly be disturbed, though the rapid examination of the locality which I made in November last did not, include any determination of this

Jan 1, 1876

By R. W. Raymond

I DESIRE to call the attention of the Institute briefly, and by no means in the way of an exhaustive description, to the interesting developments recently made on the east bank of the Hudson River, in the mining of spathic iron ores. The mines to which I refer are those of the Hudson River Spathic Iron Ore Company, situated at Oakhill on Hudson, Columbia County, N. Y., five or six miles from the city of Hudson, and opposite the town of Catskill. The ore occurs in beds, constituting apparently members of the stratified series of rocks on that side of the river, coursing nearly north and south, parallel with the river, and dipping east. The principal outcrops are presented in a range of low hills, about one mile from the river, along the crest, on the western face of which the stratum of spathic ore is more or less exposed. The length of the line in this range, along which, at various openings the ore has been discovered in profitable quantity, is about two miles. To the northward, the hills are somewhat higher, and the stratification may possibly be disturbed, though the rapid examination of the locality which I made in November last did not, include any determination of this

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By Mario L. Villa

Argentina's oil production continues in its upward trend. The year 1940 closed with an important increase over 1939; that is, 1,996,371 bbl., or 10.72 per cent. The Government oil fields (Y.P.F.) are responsible for these results, as their total output was 12,474,655 bbl., which compared with the 10,222, 533 bbl. produced in 1939 represent an increase of 2,252,122 bbl., or 22.03 per cent. Fields operated by private companies yielded 8,134,882 bbl., against 8,390,633 bbl. in 1939, a decrease of 255,751 bbl. (3.04 per cent). To the total of 20,609,538 bbl. produced in 1940 in Argentina, the Comodoro Rivadavia field contributed 14,976,222 bbl.; Plaza Huincul, 1,275,814 bbl.; the Province of Salta, 1,845,1977 bbl. and the Province of Mendoza, 2,51I,475 bbl. Table 3 compares the output of companies working in Comodoro Rivadavia. The total increase of 186,819 bbl. (1.26 per cent) registered in the Comodoro Kivadavia area is due only to an intensification of development programs in the known

Jan 1, 1941

By Mario L. Villa

Argentina's oil production continues in its upward trend. The year 1940 closed with an important increase over 1939; that is, 1,996,371 bbl., or 10.72 per cent. The Government oil fields (Y.P.F.) are responsible for these results, as their total output was 12,474,655 bbl., which compared with the 10,222, 533 bbl. produced in 1939 represent an increase of 2,252,122 bbl., or 22.03 per cent. Fields operated by private companies yielded 8,134,882 bbl., against 8,390,633 bbl. in 1939, a decrease of 255,751 bbl. (3.04 per cent). To the total of 20,609,538 bbl. produced in 1940 in Argentina, the Comodoro Rivadavia field contributed 14,976,222 bbl.; Plaza Huincul, 1,275,814 bbl.; the Province of Salta, 1,845,1977 bbl. and the Province of Mendoza, 2,51I,475 bbl. Table 3 compares the output of companies working in Comodoro Rivadavia. The total increase of 186,819 bbl. (1.26 per cent) registered in the Comodoro Kivadavia area is due only to an intensification of development programs in the known

Jan 1, 1941

By J. P. Witherow

The blast-filmace plant of the Crozer Steel and Iron Company was built under contract by Witherow & Gordon, of Pittsburgh, Pa. The furnace is 70 feet high by 16 feet bosh, tunnel-head 12 feet 8 inches, and hearth 9 feet in diameter. The columns are 20 feet high above furnace level, below which they extend 2 feet. The shell is 23 feet diameter at bottom and 19 feet at top. The plate iron is 3/8 inch at bottom, and tapers to 1/4 inch, the top ring being 5/16 inch.

Jan 1, 1884

ALLERTON S. CUSHMAN, Middletown, Ohio (written discussion*).¬ This subject is one to which I have given much thought and study and which I have frequently discussed informally with Mr. Cain and others. I have long been convinced that the gaseous elements, either combined or entrained (occluded), in steel play a much more important role than is ordinarily admitted. This is probably due to the difficulties encountered in the accurate quantitative estimation of gases, some of which Mr. Cain has referred to, as well as to the fact that, considered from the weight-percentage basis, gas content is measurable only in hundredths or even thousandths of 1 per cent. Volumetrically, however, the results ob-tained by modern research are startling, to say the least. Baraduc-Muller,1 as cited by Mr. Cain, pumped out of 1000-lb. ingots of basic Bessemer steel 2100 l. of gas. or about 75 cu. ft., at normal temperature and pressure, per ton of steel. In other words, we are to understand that Bessemer steel normally carries about fifteen times its own volume of gas. According to Baraduc-Müller's table of results, which is given here-with, carbon monoxide, nitrogen, and hydrogen are important consti-tuents of Bessemer steel, the latter gas being undoubtedly formed by the

Jan 11, 1919

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By George Kunz

(Butte Meeting, August, 1913.) THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely clue the eventual success of this eminently desirable reform, which lie has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3

Jan 7, 1913

By George Frederick Kunz

The manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg.; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a ki1ogram. He also called attention to the fact that while this would depreciate the present diamoiid carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.' The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sévres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3 The general adoption of a uniform standard for dealings in pre-

Jan 1, 1914

Forty-three years ago a record for low cost was made at the Spanish mine, in Nevada county, California. In 22 days of September, 1887, there was mined 2796 tons of ore at a cost of 37.5 cents per ton, of which 32.4 cents was for labor and 5.1 cents for supplies. The mill treated this ore for 23 cents per ton, of which 12.3 cents was for labor and 10.7 cents for supplies. Thus the total operating cost was 60.5 cents per ton. The yield was $1.16 in gold per ton, leaving a profit of 56 cents per ton, or 48 per cent of the yield. The mine was an open-cut in a schist formation on a hillside and the work was done by Chinese laborers that were paid $1.40 per shift. The ore was soft, and could be ground effectively in four Hunting- ton mills, supplemented by silvered amalgamating plates.* The engineer in charge was F. W. Bradley, a student from the University of California. As has been indicated, the conditions were unusually favorable in respect of softness of ore, accessibility to the mill, metallurgic simplicity, with cheap labor and power, but even at that the results were so remark- able as to attract general attention, which, as might be expected, was magnified, for advertising purposes, by the manufacturers of the Huntington mill, the firm of Parke & Lacy, at San Francisco. The record made at the Spanish mine therefore found its way into many textbooks on mining published at that time. The editor of the 'Mining and Scientific Press'† (at that date, Charles G. Yale) evidently took a warm interest in. the

Jan 1, 1932

By R. G. Davies, P. Beardmore, T. L. Johnston

The flow stress of a series of Ni-Cr-A1 alloys consisting of a dispersion of y' (based on Ni3Al) in a rnatrix of nickel-base solid solution y has been measured at temperatures up to 950°C as a fwzction of the volume fraction of y'. At high temperatures the flow stress is controlled by the amount of Y' in the alloy, i.e., the higher the volume fraction of y', the greater is the flow stress. This simple relationship is not obeyed at low temperatures in so far as a peak in the flow stress-volume fraction relation occurs at about 25 pct y'. The variation in the mechanical properlies of these alloys as a function of both temperature and volume fraction of y' has been correlated with changes in distribution of both the dislocations and y'. The results are interpreted on the basis that at low temperatures the y matrix is strengthened significantly bv the presence of a hyperfine y' precipitate due to decomposition on cooling; at high temperatures the y matrix is a single phase of low strength. It is clearly recognized that the high temperature strength of most nickel-base superalloys depends upon a dispersion of the ordered fcc phase y', based on Ni3A1, in a fcc solid solution matrix y based on nickel. Although the volume fraction of y' varies widely from about 0.2 in Nimonic 80A to about 0.6 in Mar-M200, all such nickel-base alloys manifest an unusual insensi-tivity of the flow stress with respect to temperature. In Mar-M200 for example, the 0.2 pct flow stress remains essentially constant from room temperature to 750°C. The conclusion has been drawn1 that the characteristically low temperature dependence of the flow stress of y-y' nickel-base alloys is obtained when the state of dispersion of y' is such that dislocations are forced to cut through the y' particles at the onset of yielding. When the spacing between the y' particles is so large that the flow stress is controlled by dislocation bowing between particles, then the initial flow stress decreases progressively with an increase in temperature at a rate determined by changes in elastic properties. The same conclusion is inherent in the detailed, mechanistic model of the deformation process in commercial superalloys which has been developed by Copley and ear' in which the temperature independent flow stress is attributed primarily to the contribution of the antiphase boundary energy created in the y' particles during deformation. In this theory the temperature insensitivity of the flow stress is a reflection of the constant antiphase boundary energy as a function of temperature. An important microstructural parameter that is relevant to the explanations that have been suggested' to account for the temperature insensitivity of the flow stress is the volume fraction of y'. To vary the latter to any significant extent in a given commercial alloy is clearly difficult. However, it is possible in a relatively simple Ni-Al-Cr ternary system which manifests analogous microstructures in terms of the distribution of y' in y and contains specific alloys which have flow properties that depend on temperature in a manner quite similar to their more complex commercial counterparts. Hornbogen et . have studied precipitation phenomena and deformation mechanisms in such alloys but only where the y' volume fraction was small (less than 0.2) and the y' particle size varied from less than 100A up to a maximum of -1000A. In the present study, a series of alloys was prepared in which the volume percent of y' at 900°C was varied from 0 to 100 pct with the y' particle size (of the order 0.5 p) comparable to the sizes obtained in commercial superalloys. Particular attention has been given to the relationship between variations in the volume fraction and distribution of y' and the temperature dependence of the flow stress EXPERIMENTAL TECHNIQUES The Ni-Cr-Al system was selected because it is well characterized, bears a close relationship to commercial alloys, and offers the advantage of an extra degree of freedom over a binary system. In the present investigation, a series of alloys across the tie line between NisA1 and Ni3Cr (Ni3Cr is not an in-termetallic compound, the nomenclature is only used to designate the composition) were vacuum cast. The pseudobinary6 and the composition of the alloys used are shown in Fig. 1. It is important to note that the compositions of the y phase and the y' phase in the two-phase alloys was always the same. Alloy compositions were selected from the binary diagram, Fig. 1, in order that aging at 900°C would produce from 0 (100 pct y) to 100 pct y' by volume percent. (The size of the y' particles produced during the equilibrium aging treatment increased as the volume fraction of y' increased, ranging from about 0.2 p at low volume fractions up to about 0.8 p at the highest volume fraction.) The y' phase is based on the inter-metallic compound Ni,A1 which has the fcc LIZ type superlattice structure, and chromium substitutes for aluminum in the structure. The y phase is a disordered fcc solid solution. The alloys were heat treated at 1150°C for 2 hr, air cooled to room temperature, and finally annealed for 16 hr at 900°C. The rods were then centerless ground to 0.25 in. diam and cut into compression samples 0.5 in. long. The compression tests were made on an In-stron machine at a strain rate of 7 x 10"4 sec-'. A rapid heating radiant heat furnace was used which minimized the heating and temperature stabilization time to 10 min for the highest testing temperature. All the tests were stopped after 5 pct plastic strain.

Jan 1, 1970

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson' indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel's' data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,' Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By Lawrence Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope4 at the supports (Fig. 1). Essentially this assumes:5,6 [BA = OD = 0 and dA = dB = 0.]

Jan 10, 1959

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity, ' innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1985

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

Discussion of the paper of EDWARD G. NORTON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 1915, pp. 93 to 102. G. D. HARRIS, Ithaca, N. Y. (communication to the Secretary *).¬Since I have on several occasions1 expressed at length my general views on this interesting subject, it seems fitting that I endeavor here to comment as briefly as possible on a few points suggested by the paper. Doubtless you all know of the rather extensive publications of Lachmann on mid-European salines and his scarcely successful, attempt to make the phenomena presented by our domes fit. into his "Exzeme" theory based on studies of European phenomena. This paper is a most welcome indication that scientific America is very much alive to the difficulties that have been encountered in attempts already made to explain the origin of the salt domes in the lower Mississippi embayment region. Praiseworthy, too, is the attempt to explain these phenomena by agencies still in operation. I may, perhaps, be permitted to state here that a former student of mine, and co-worker in Louisiana, A. C. Veatch, is now interested in the Algerian region, where it would seem similar dome-phenomena are to be found, and hopes may well

Jan 5, 1915

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943