Search Documents

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide's Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By Kenneth E. Gray

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By C. S. Cole

CO-CHAIRMAN CARTER S. Cole l-The stimulus of war definitely increases interest in the subject we are discussing at this Symposium. There have been, in the past, other symposia on this subject and there probably will be still others in the future, but I feel sure that this one will go down as one of the most important that have ever been held on the subject. In 1918 A.S.T.M. held a Symposium on Stress- Corrosion Cracking that was confined entirely to brass, because at that time few people were interested in the phenomenon as it applied to other metals. Again under the stimulus of war, we are gathered to discuss the subject, but this time brass alone is but part of our interest. It is interesting to note more papers on brass will be presented than there were in the 1918 session, but these brass papers, you will also note, comprise less than half our program. Aluminum, magnesium and

Jan 1, 1945

By S. C. Sircar, D. R. Wiles

The rate has been studied of the hydrogen reduction of nickel ions in acetate -buffered solutions, using a nickel catalyst. At temperatures between 130°and 160°C, the rate is found to be proportional to the catalyst area, the nickel ion concentration, and the hydrogen pressure. The effect of hydrogen ions is to reduce the observed rate, likely by causing the reverse reaction (dissolution) to proceed. The experimental activation energy was found to be 25 kcal per mole. THE precipitation of metals and lower oxides from solution by hydrogen reduction has been quite actively investigated during the past few years.1 In the case of nickel, the kinetics of the precipitation have been studied in ammonia solution2 but extension of this study to acid solutions has not attracted much interest, largely because of the unfavorable thermodynamics at all but the lowest acidities. For example, Schaufelberger foundg that only 10 pct reduction of nickel could be effected in sulphate solutions. One kinetic study of the reduction of Ni++ has been reported by Knacke, Pawlek, and Sussmuth,4 in which the order of the reaction was found to be one in nickel ion and one-half in hydrogen pressure. No mention was made as to the part played by the nickel catalyst, or by the pH of the solution. Moreover, the activation energy reported (4 .12 kcal per mole) is so low as to lead to some question as to whether diffusion might be playing a major role in determining the kinetics. We have recently completed a study5 of the kinetics of the hydrogen precipitation of nickel from acetate-buffered acidic solutions whose results confirm and amplify those of Knacke et al. EXPERIMENTAL PROCEDURES The work was done in a high-pressure autoclavee by the usual technique of removing small samples of the solution for analysis. Nickel analysis was done colorimetrically by the dimethylglyoxime method.' The catalyst used was carbonyl nickel powder (Standard A powder of the Mond Nickel Co., Ltd.) which was found to be composed of spheres of less than 350 mesh. The surface area of the powder was determined in this laboratory by the B. E. T. method to be 1.85 sq m (m2) per g. The catalyst was added to the solution only after the proper temperature and pressure had been reached. Agitation of the baffled system was by a turbine-type impeller, rotated at speeds between 400 and 750 rpm. The reduction rate was found to be independent of the stirring rate, so it was assumed that diffusion in the liquid does not limit the rate. In typical experiments, the nickel concentration was unchanged during an induction period of variable length. The concentration then decreased sharply, and gradually levelled off to approach the final equilibrium value. In some cases, notably at high stirring rates, the nickel concentration was found to increase considerably during the induction period, and then to decrease. In all cases, the rate was determined from the slope of the tangent to the rate curve as the concentration first decreased below the initial value. This is seen in Fig. 1. The rate measurements were found to be reproducible to within about 5 and to be quite independent of the nature or duration of the induction period. The range of conditions used is given in Table I.

Jan 1, 1961

By C. L. Sollenbeger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature1,2 to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent. In the All is-Chalmers Research Laboratories a systematic study was made of the effect of different alkali-silica ratios on the concentration by flotation of two scheelite ores. One of these was a high grade ore from the Sang Dong mine in Korea. The effect of such factors as pH; addition agents; and conditioning time, temperature, and pulp density on the flotation efficiency of this ore have been described previously. The other ore was a low grade ore from Getchell Mines Inc., Nevada. The mineralogy and techniques of concentrating this ore have been described by Kunze. Hereafter these ores will be referred to as the Korean and Nevada ores. Experiments were made with both to determine the effect of three factors—-type of silicate, concentration of silicate, and pH of the pulp—on recovery and grade of tungsten in a rougher concentrate. Average WO, content of the Korean ore was 1.50 pct and of the Nevada ore 0.27 pct. The predominant tungsten mineral in both ores was scheelite, which was accompanied by a small amount of powellite. The powellite and scheelite were finely disseminated through both ores and required a —200 mesh grind for liberation. Major gangue minerals in the Korean ore, in decreasing order of abundance, were amphi-boles, quartz, biotite, garnet, fluorite, and calcite. Bulk sulfides composed about 3 pct of the total weight. Gangue in the Nevada ore, in descending order of abundance, was garnet, alpha quartz, calcite, phlogopite, wollastonite, and amphiboles. Sulfide minerals were 3 to 4 pct of total weight. Batch flotation experiments were made with 500-g samples of ore, each sample wet-ground to 90 pct passing 200 mesh. The finely ground ore was floated in a Fagergren batch cell at 25 pct solids. The natural pH of the Nevada ore was 8.9 and of the Korean ore, 8.5. The D, RU, K, N, and S-35 sodium silicates were obtained in colloidal dispersions with varying amounts of water. The most alkaline, Metso, was in dry powdered form. For convenience in addition, 5 pct solutions by weight were prepared from each of the silicates, on the basis of dry sodium silicate dissolved in the correct amount of distilled water. Chemical analyses of the various silicates are given in Table I, together with the pH of the 5 pct solutions. A preliminary bulk sulfide float was made with secondary butyl xanthate as the collector and pine oil as the frother. The WO] analysis of the sulfide concentrate was nearly 1 pct for the Korean ore and about 0.1 pct for the Nevada ore. The tungsten contained in the sulfide concentrate constituted about 3 pct of the total tungsten in each ore. No effort was made to recover these tungsten values. The scheelite was floated with oleic acid. Adjustments in pH were made with sulfuric acid or sodium carbonate. A 1 pct solution of 85 pct Aerosol OT was sprayed on the froth and sides of the cell during the scheelite float to aid in dispersing the minerals and to decrease the entrapment of gangue particles. Six tests were planned for each of the six types of silicate in which concentrations of 1, 2, and 4 1b of silicate per ton of dry ore were investigated at both 6.5 and 10 pH. All tests were made at room temperature. The performance of each silicate was judged from the grade and recovery of WO, in the scheelite rougher concentrate. Tungsten recovery was calculated on the basis of the scheelite remaining in the ore after the preliminary sulfide float. Testing of each silicate at three levels of concentration and two levels of pH required 36 tests with each scheelite ore. Variance analyses were performed on the concentrate grades and recoveries to determine whether or not the type of sodium silicate, the concentration of sodium silicate, or the pH significantly affected recovery or grade. Results Concentrate Grade: A variance analysis of the concentrate grades for the Korean ore showed that concentration of the silicate and pH of the ore pulp were major factors in producing a high grade concentrate. Also, the silica- to-so da ratio was important as an interaction with pH. The concentrate grade vs silica-to-soda ratio is plotted in Fig. 1. The curves show that the concentrate grade improved with an increase in concentration of sodium silicate and also

Jan 1, 1959

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate') may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.' The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

Jan 1, 1969

By J. D. Livingston

THE hardening of alloys by the precipitation of a second phase has long been an important technological process. One approach towards improving our understanding of this phenomenon has been a correlation of mechanical properties with such parameters as particle size and inter par ticle spacing.' Several reviews of such data have appeared.2-4 A major limitation to this approach has been that for most alloys the particles are submicroscopic in size in the range of optimum hardness. Precipitation-hardening copper-cobalt alloys, therefore, are of interest, because the ferromagnetic properties of the precipitate make it possible to measure particle size, number of particles, and so forth, from magnetic measurements alone.5, 6 Livingston and Becker7 have applied these techniques to a study of precipitation hardening in an alloy of 2 pct Co in copper. It was found from magnetic measurements that nearly all the cobalt to be precipitated was out of solution within a few minutes at 600°C, whereas the peak in tensile yield stress was not attained until a much longer aging time. Thus during the first 1000 min of aging time at 600°C the Yield stress was increasing while a constant volume of precipitate was coarsening, i.e., while particle size and interparticle spacing were increasing. Peak yield stress was reached at an average particle radius of about 70A. The earlier study was confined to one alloy at one aging temperature, so that the volume fraction of precipitate was fixed and, therefore, particle size and interparticle spacing could not be independently varied. The work has now been extended to several alloys of varying percentage cobalt in copper, and to aging at various temperatures. It was hoped that such a study might clarify the relative importance to precipitation hardening of particle size, interparticle spacing, and volume fraction of precipitate. EXPERIMENT The alloys studied contained 0.7, 1.3, 2.0, and 3.2 wt pct Co in copper. They were prepared from electrolytic copper and electrolytic cobalt in a vacuum -induction furnace, worked to 3/8-in.-diam rod, and machined into tensile specimens with a gage section 1 1/2 in. long and 3/16 in. in diam. All specimens were given a solution treatment consisting of a 30-min anneal in nitrogen at 1000° C followed by a quench into iced brine. Subsequent aging was done in nitrogen and followed by a water quench. Average grain diameter was approximately 0.01 in.

Jan 1, 1960

Henry C. Carlisle: This is a husband-and-wife act, in which Mary Carlisle is going to listen, and break in as often as she feels like it. I am going to describe my career as a mining engineer. We are at Nantucket, in the 75 Main St. house; The year is 1959. Q: This is something the boys and I have wanted you to do for a long time. Carlisle: After leaving Columbia in 1910, I arrived at Ray, Ariz., January 1, 1911, and rustled a job from Louis Cates, Ralph Nowland and Sprott Boyd, who were running the Ray mine. I went to work as a surveyor's helper, made $90 a month, and paid $35 a month board. I lived in a dormitory where about 25 other engineers, graduates from different colleges, were living. It was very social and you made a lot of young friends early in the game. I did not think much of the idea of being a surveyor, or even a surveyors, helper; the higher-up surveyors only got $125 a month, and had been there quite a long time. So, I asked to be changed to underground sampling, where I would see the mine faces every day and learn more about mining. In about three months, I became an underground sampler and remained at this for a year, but in three months I was promoted to head sampler, with six people under me.

Jan 10, 1963

Discussion of the paper of C. M. YOUNG, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1369 to 1384. CARL SCHOLZ, Chicago, Ill.-Mr. Young was kind enough to' allude to the development of a mine in which I am now engaged. Several months ago the Burlington Railroad decided to open a mine in the field Which they own in Franklin County containing some 15,000 acres .(6070 ha.) of coal, ranging in thickness from 8 to 12 ft. (2 to 3.6 m.). This proposition in itself is attractive to any mining engineer, but with the backing of a large company I saw an opportunity to do some novel work in the construction line, and for several months I have been investigating and working on the problem of developing what I hope will be the largest and best equipped mine in the State of Illinois. The shaft will be sunk at a place where the coal lies at a depth of 600 ft. (182 m.) and conditions both of the surface and of the coal are ideal in every way; the seam is almost level, and we had only 7 ft. (2 m.) of surface clay to go through. We are going to hoist by skips in order to reduce the rope speed. I believe that is a long step in the direction of economy, because we not only double the output of the mine by hoisting the contents of two cars atone time, but we reduce the proportion of dead weight. In our case there will be 20 tons of coal and 18,000 lb. of skip, or 55 per cent. net and 45 per cent. tare. That, of course, necessitates less than half the rope speed for the same tonnage, and we all know that speed means power and power means cost. Skip hoisting permits the use of solid-end gate cars, which is an advantage. The cost of these cars will be in the neighborhood of $250 apiece; They are well built, with roller-bearing wheels of the most up-to-date type, spring draw-bars, and refinements of-that character which are necessary to move the loads most advantageously.

Jan 1, 1918

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson' obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock' used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,&apos; which had been used since the early 1930&apos;s by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell&apos;s plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell&apos;s practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By James Norman, E. W. Gieseke

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content. it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, [t] the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2, 3 The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. STUDY OF METHOD OF FLOTATION SEPARATION Most of the work on concentration of spodumene was done with rock from near King&apos;s Mountain, North Carolina. Rock from two

Jan 1, 1940

By Leroy Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com-parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of ques-tionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to com-plete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accu-rately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation.

Jan 1, 1938

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout&apos; Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

By H. E. Cline

Calculations of the formation and growth of faults caused by a variation in lumellar widths were made for a two-dimensioml three-plate problem. The angle between the a-ß boundary and the growth direction was allowed to vary and the time evolution was studied using a quasisteady state approach. At spacings smaller than a critical spacing given by X V = AO variations in the larrlellar widths grow in time to produce faults that coarsen the structure, while at spac-ings larger than this critical spacing, variations in the lamellar widths decay in time. If small plates are introduced into the structure they may grow only at large spacings to refine the structure. The time evolution and shape of faults were calculated for the three plate-problem and then the three dimensional problem and rod-like eutectic were qualitatively discussed. UNDERSTANDING of the mechanism by which the spacing of directionally solidified eutectics is determined may allow one to control their structure better. Steady state solutions for the growth of lamellar structures have been found for a range of lamellar spacings A and growth velocities V. To obtain a unique solution for the isothermal growth of pearlite, Zener1 assumed that growth occurs at a maximum velocity, while Tiller2 assumed that a eutectic alloy, grown under an imposed velocity, will choose a spacing corresponding to minimum undercooling. These assumptions are equivalent and have been referred to as "extremum growth". The extremum condition predicts the observed relation between velocity and spacing as given by V = constant [I] but does not provide a mechanism for changing the lamellar spacing. Jackson and Hunt3 calculated the interface shape by using solutions to the diffusion equation for a planar interface and a relation of the interface composition to the local curvature. If the spacing is much larger than the extremum spacing, the interface breaks down catastrophically to form forked plates. However, the catastrophic breakdown cannot account for the small adjustments in spacing that must occur in practice..3 Direct observations during the growth of organic eutectics4 and the Pb-Sn eutectic5 show that spacing changes occur by the formation of faults. A fault in a plate-like eutectic is the edge of a plate. Once the faults form, they may move to make small adjustments in the spacing.6,3 The motion of faults intersecting the growing interface was shown by an approximate analysis to give Eq. [I].6 A perfectly regular lamellar structure should be able to persist over a range of lamellar spacings. However, during growth small perturbations in the structure may occur. If the amplitude of the perturbation increases in time the structure is unstable, while if all possible perturbations decrease in time the structure is stable. In a previous paper7 variations in the shape of the solid-liquid interface were considered, while this paper considers only variations in lamellar widths while maintaining a macroscopically planar solid-liquid interface. Previously, theories of lamellar growth1"3 have artificially contrained the growth to give a regular periodic structure. To allow for a variation in spacing, the three phase intersections and groove angles were allowed to change with time as determined by assuming local equilibrium. THREE-PLATE PROBLEM Since the spacing changes in eutectics by local formation of faults,4&apos;5 it is suggested that local variations in spacing are responsible. The interaction between neighboring plates will be greatest because they have the smallest diffusion distance. For simplicity, as a nearest neighbor approximation, a three-plate problem will be considered, as illustrated in Fig. 1. The structure consists of a periodic array in which all the plates are allowed to vary in width. As in steady state growth it is assumed that the average composition in the solid remains constant. A variation in plate widths, that maintains the composition in the solid, was introduced by making the first a-phase plate thinner by an amount A, keeping the width of the second B-phase plate constant, and increasing the width of the third a-phase plate. If the structure were not perturbed, as in the regular two-plate problem previously described,&apos; then the groove angles at the three-phase junctions are the equilibrium angles, 0, and ? B, and the solid-solid boundary is normal to the interface. In the three-plate problem with a variation in plate widths the phase boundaries are assumed to be related to the three-phase junction by equilibrium angles, but the a/B boundaries may be rotated by an angle 0 from the growth direction. The angle H be-tween the tangent to the a/B boundary and the growth direction may vary during growth and determine the —> — — —.A_ Q-0 / 0 x, X2 Fig. 1—Schematic of the three-plate problem showing a variation in the spacing and the effect on the angles at the three phase intersections.

Jan 1, 1970

H. 0. HOFMAN, Boston, Mass (written discussion*).-The paper by Mr.. Pyne gives clear evidence of the difficulties the metallurgist is likely to encounter when he tries to recover in the blast furnace the metal from old chromite lining used as a refractory material in the copper reverberatory furnace. It appears that chromite cannot be fluxed at temperatures which usually prevail in copper blast furnaces. This calls to mind the freezing-point curve drawn by M. Simonis1 of mixtures of chromite and kaolinite. The chromite used in the experiments contained 52.9 per cent. Cr203, 22.6 FeO, 4.8 AI203, 9.6 Si02, .10.1-MgO; FIG. 1. the kaolinite was clay from Zettlitz with 98.5 per cent. clay-substance: The accompanying curve shows that the eutectic mixture with 35 per cent. kaolinite and 65 per cent. chromite freezes at Seger cone No. 15 (1435° C.), while kaolinite fuses at cone No. 35 (1770° C.) and chromite at cone No. 42 (2000° C.). The curve indicates that the difficulty in the blast furnace can be overcome by having at the smelting zone a temperature much higher than is usual in copper smelting; a charge composition similar to that prevailing at the Mansfeld copper smeltery -which gives with 23 per cent. coke a, slag of the composition Si02, .49.09; .(FeMg)0, 5.58; (CaMg)0, 16.02; A1203,-16.02-might flux and fuse chromite.

Jan 3, 1918