Search Documents

Jan 1, 1903

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

INTRODUCTION IT is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles.1.2,3 The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4,5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik's tests will be discussed later. Such torsion does not readily yield actual stress and strain values. Therefore a preliminary study was made of the effects of repeated direct stresses, i.e., tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluminum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension test. This alloy permitted, therefore, rather accurate control at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this investigation appear sufficiently interesting to extend the method of attack in various directions. It is intended to study (I) the effects of cycles up to a few thousands and (2) the effects of strains of different magnitude in tension and compression, respectively. The latter variable also includes as a special case the effects of compressive strains.

Jan 1, 1948

James W. Neill, Pasadena, Cal. (communication to the Secretary*):—Professor Hofnlan's paper brings the art up to date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there mas at the concentrator an unusually large protluction of a middle product, locally called " iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a " roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the uslial construction, about 2 by 4 ft. in dimensions, with a hollon- cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it tlush with the lip, or apron, and above the tuybres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a Can-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow. The fine material which had renlained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and

Jan 1, 1911

By John M. Sharp

John M. Sharp, Jr. (Assistant Professor of Geology, University of Missouri, Columbia, Mo.)-Geothermal gradient and surface temperature data anomalies are potentially useful tools in mineral exploration, These data, however, may reflect a number of geologic and hydrologic processes as well as the thermophysical properties of the geologic materials. The author presents a relatively simple model which may be of value in mineral exploration. The lack of consideration of other processes, however, limits its usefulness. For instance, because of erosion or sediment deposition over geologic time the land surface must be considered a moving boundary in such a model. Evaluation of this effect coupled with annual surface temperature and thermal conductivity variations can result in temperature profiles such as shown in [Figs. 4 to 7]. These effects and others, such as ground-water movement," must be considered and filtered from the data before proper interpretation is possible. Another assumption which should have been discussed is, why were the observed mean surface temperatures not used for extrapolation of the gradients in [Figs. 4, 6, and 7?] Conductive heat transport responds to the actual boundary (land surface) temperature, not to theoretical temperatures in the absence of perturbations. Benfield presents a theoretical model for calculating perturbations in the geothermal gradient for erosion and sedimentation. The temperature (T) at any time (t) and any depth below the surface (x) is given by [ ] where T is the mean surface temperature, G, the geothermal gradient, v, the rate of erosion (or sedimentation),[ ], the long-term rate of change of T0, and k is the thermal diffusivity of the rock. Using the author's values and a rate of erosion of 1.54 cm per yr for a period of 10,000 yr, a thermal profile as shown in [Fig. 10] will be generated. A thermal diffusivity of 0.0164 sq cm per sec was used, corresponding to a thermal conductivity of 0.0082 cal per cm per sec per C. In [Fig. 11], a sediment deposition rate of 3.0 cm per yr for a period of 1000 yr was used to generate the subsurface temperature profile. A surface temperature of 24.3°C was used, as specified in [Fig. 9, 7], was set equal to zero for both cases. Superposition on the generated profiles in [Figs. 10 and 11] of the annual surface temperature variation perturbation (which may be calculated in a number of ways) will yield profiles similar to those in [Figs. 4 and 7]. Similar profiles can also be produced by regional ground-water flow. Models like the author's can be of value in mineral exploration. Other processes, however, which affect surface temperatures and gradients must first be considered, calculated, and filtered from the data if anything but the crudest qualitative interpretation is to be made. Robert C. Edmiston (Author's reply)-Professor Sharp has raised three objections to my interpretation of the subsurface temperature data I collected at Silver Bell. These are: 1) No correction was made for erosion or sedimentation,

Jan 1, 1977

By William H. Kobbé

THE CHAIRMAN (M. L. REQUA, San Francisco, Cal.).-We have had in California a great deal of trouble from the breaking. off and collapsing of well casings from shifting sand, and it is quite true with us as indicated in the paper, that no casing has been found sufficiently strong to withstand that. I know of wells in which casing that has not been in the hole over 2 or 3 days has collapsed and when that casing has, been pulled out it has been just as flat as your hand. I am also familiar with swelling bed rock in the gold drift mining ground of California. It does swell and keeps on swelling and never seems to stop. Just as long as tunnels are kept open in that kind of material there has to be a gang going through the tunnel constantly cutting out and easing up. They have put in timbers 24 in. in diameter in an effort to hold that kind of ground and it has always filled. The only way to succeed is to keep a gang of men busy all the time cutting out and easing down as it squeezes in. C. NARAMORE, Washington, D. C.-My experience has been very similar to yours in, the same field in the matter of breaking off of casing. I had charge of one well, in which I put in reënforced casing, anchored it in place and got 1 day's production, 150 bbl., out of it. The following morning my lease foreman telephoned that it had broken off. I thought at that time we would have more evidence, so I drove out to the well without ordering a new shoe joint. It had been customary to merely start from town with a new shoe joint, pull the pipe, take off the crooked bottom joint, start the casing back and sometimes never touch any iron (lost casing)- when redrilling the well. Where the flattened joints went

Jan 4, 1917

By H. O. Pickard

The Hoover and Mason Phosphate Co. made extensive tests with a rig manufactured by the Paris Manufacturing CO. as shown in Fig I. It is powered by a 20-hp Wisconsin air-cooled gasoline engine, through a single reduction gear and flexible coupling. The machine operates a 4-in. auger with a detachable cutting head, as shown in Fig I. The auger length is 3 ft 4 in. and the cutting head averages 7 in. The unit has a drilling capacity of 100 ft and can drill an average prospect hole in less than 15 min. The weight of the motor is used for the thrust feed for driving the auger and head down, aided by the spiral shape of the auger. The rate of downward motion—i.e., the feed—is regulated by a handwheel. The string of tools is withdrawn from the hole by a gear train controlled by a hand-operated clutch. In fairly dry strata, not of the consistency of mud, the action of the auger

Jan 1, 1948

By H. O. Pickard

The Hoover and Mason Phosphate Co. made extensive tests with a rig manufactured by the Paris Manufacturing CO. as shown in Fig I. It is powered by a 20-hp Wisconsin air-cooled gasoline engine, through a single reduction gear and flexible coupling. The machine operates a 4-in. auger with a detachable cutting head, as shown in Fig I. The auger length is 3 ft 4 in. and the cutting head averages 7 in. The unit has a drilling capacity of 100 ft and can drill an average prospect hole in less than 15 min. The weight of the motor is used for the thrust feed for driving the auger and head down, aided by the spiral shape of the auger. The rate of downward motion—i.e., the feed—is regulated by a handwheel. The string of tools is withdrawn from the hole by a gear train controlled by a hand-operated clutch. In fairly dry strata, not of the consistency of mud, the action of the auger

Jan 1, 1948

By Kendall E. Born

Production of crude oil in Tennessee during 1943 was approximately 8200 bbl., slightly less than the 1942 production, Counties. Some half dozen wells in Clay, Fentress, and Pickett Counties, pumped intermittently, produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The Morgan County production was about I0,000,000 cu. ft. and approximately 8,000,000 cu. ft. was produced from the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Thirteen wells were spudded during the year; three were drilling on Dec. I, 1943. Of the nine completions, representing 10,488 ft. of hole, three were gas' wells of commercial size although only one of them has been placed on the line. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Pluteuz.-There were three completions in the northern part of

Jan 1, 1944

By Kendall E. Born

Production of crude oil in Tennessee during 1943 was approximately 8200 bbl., slightly less than the 1942 production, Counties. Some half dozen wells in Clay, Fentress, and Pickett Counties, pumped intermittently, produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The Morgan County production was about I0,000,000 cu. ft. and approximately 8,000,000 cu. ft. was produced from the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Thirteen wells were spudded during the year; three were drilling on Dec. I, 1943. Of the nine completions, representing 10,488 ft. of hole, three were gas' wells of commercial size although only one of them has been placed on the line. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Pluteuz.-There were three completions in the northern part of

Jan 1, 1944

ON Oct. 5, 1926, the day before the general ses-sions of the fall meeting of the American Insti-tute of Mining and Metallurgical Engineers at Pittsburgh, a round table conference on the combus-tibility and testing of coke was held at the Bureau of Mines Experiment Station. There were about fifty present, with A. C. Fieldner, chief chemist of the Bureau of Mines, as chairman. The following organi-zations were represented: American Institute of Min-ing and Metallurgical Engineers, American Society for Testing Materials, American Gas Association, Eastern States Blast Furnace and Coke Oven Association, Gas and Fuel Division of, American Chemical Society, and Southern Ohio Pig Iron and Coke Association. In opening the proceedings, Mr. Fieldner explained that the meeting had been called at the suggestion of several members of the Institute and members of other organizations. The subject is of interest to the pro-ducer and the user of coke whether it be in a blast furnace, cupola furnace, house-heating furnace, open grate, gas producer, or in a water-gas generator. There has been much confusion on this subject largely because there is no common definition of combustibility. Does the blast-furnace superintendent, the coke-oven operator, and the fuel engineer have the same under-standing of the term "combustibility"? If a common understanding can be reached, many differences of opinion will disappear. COMBUSTIBILITY OF COKE R. H. Sweetser of Columbus, Ohio, disagreed with the statement of P. H. Royster, T. L. Joseph, and S. P. Kinney in Reports of Investigations, Serial No. 2524, of the Bureau of Mines, in which it was stated that the coke-oven op-erator cannot change coke combustibility by modifying oven practice. Mr. Sweetser held that the coke-oven man can change the combustibility of coke. Blast-furnace men know that coke that will burn easily with low pressure and will. come down in the regular way in the furnace can be pro-duced from a given mixture of coal. His idea of the combustibility of coke is the rate of flow through the com-bustion zone of the blast furnace. If the coke does not pass through in normal manner it is highly incombustible. H. J. Rose of the Koppers Co., Pittsburgh, objected to being pinned down so closely on this phase of the com-bustibility and incombustibility of coke. Coke-oven men are frequently obliged to change oven conditions to make a coke which gives blast-furnace men what they want. The size of the coke and the screening have an important bear-ing on combustibility, and there are many cases on record where by simply changing the different sizes of the coke, everything worked smoothly, and that is a much more combustible coke.

Jan 1, 1927

By Leonard Waldo

PROBABLY some of the views advanced in this paper will appear, from a metallurgical standpoint, little less than revolutionary. It is with considerable hesitancy that I venture to offer a few thoughts concerning what, seems to me to be perhaps the most important development of metallurgy since the introduction of Bessemer steel. Dr. John Percy, with that rare insight which characterizes the epoch-making man, described in a communication to the Royal Society, about 1855, an alloy of duminum and copper which he called aluminum-bronze. The name has "stuck." The term "bronze" has been so variously used that I confess I do not know exactly what constitutes a bronze; but I know that in the great materials of engineering simplicity of composition is a cardinal excellence; and I wish to venture the suggestion that aluminum-bronze is not an alloy of aluminum and copper in any such sense as the compounds of tin and zinc with copper (except the copper-tin compound SnCn3) are alloys. There are several reasons which lead me to this view. In the first place, if a series of bars be prepared containing varying percentages of aluminum and copper, and the electrical conductivity of these bars be carefully determined, a curve of conductivity will be obtained, as shown in Fig. 1, which represents the result of such experiments. While I am not sure, at this time, that the values of conductivity shown in this diagram are wholly dependent upon the percentage of aluminum added, the assumption is a probable one; and the curve indicates that an extremely small percentage of aluminum affects the conductivity in a ratio out of all proportion to the amount of that metal. Another reason is drawn directly from experience in the foundry. If we take from the furnace a crucible containing melted aluminum and one containing melted copper, both at a little more than a red heat, and pour them together, the reaction is so intense that the

Jan 1, 1895

Discussion of a paper of S. S. Rummy and W. F. SCHWEDES, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2613 to 2635. K. A. PAULY, Schenectady, N. Y.-I have seen this installation and I wish all those interested in the question of electricity as a mine pumping agent could see it. It is not only a model for mine installation, but might well serve as a model for any electrically driven pumping plant. I think I am correct in saying that the pumps are the largest electrically operated centrifugal pumps in mine service in America. I talked with Mr. Rumsey in Duluth just before coming here, and he told me that the actual tests of the equipment as installed checked very closely with the shop tests; that the water delivered by the pumps was slightly in excess of the guarantee, something like 3 or 4 per cent., and that no troubles except of a very minor nature had been experienced with the installation from the start. One point which has been brought out by Mr. Rumsey, and by others who have looked into this question, is the marked saving which' can be made by the application of electricity to pumps, especially to the main sump pumps. The pumps are always located a long distance from the boiler plant and the losses in the steam mains are large. While many of the steam pumps are of a very high grade, yet the tests seemed to indicate that the steam consumption is extremely large. The reduction in operating cost of one small installation which I. have in mind pumping against a head of approximately 2,000 ft.-which by the way was a reciprocating pump-reduced the pumping cost to the neighborhood of one-fifth of the previous steam cost. . The high steam cost was probably due to leakage in the engine and the loss in transmission in the mine, the pumps being located almost half a, mile from the boiler plant.

Jan 4, 1915

By H. L. Hopkins, L. W. Kempf

Aluminum alloys, in common with most other metallic alloys exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with temperature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative consideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators '-5t have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys Subcommittee, during 1917 and 1918, which are not generally available in published form. In these reports the term "permanent growth" was applied to the dimensional changes occurring in the pistons at the tem-

Jan 1, 1936

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946

By O. Chanute

all of' level atid grade curve excepting Nos. 897, 898, 899, and 900, because of the impossibility of grouping them in the same nlonner, no two Iraving the chemical composition and physical prnprtiw as tho only v:iriubles. Phosphorus ~tnits have been taken to show the relatia h:wdnes. Of these 16 groups, 10 decidedly indicate slower wear firr tile harder rail. Of the remaining 6 groups, three (groups 2, 9, and 15) come well within the limits of error (.25 pound per yard) inherent in the palculation of the data as pointed out by Dr. Dndley; they catrnot, therefore, be considered tls exceptions. Group 2 and 15 arc but little outside of the limita of error. Rail 923 of group 9 is obviously abnornlal. This is probahly due to its being overheated, which the chemical analysis shows might easily be the case, and which the physical tc~ts and its low specific gravity tend to c-nfirm. We inry say, then, thnt 13 of these 16 groups fairly indicate, if they do not definitely point out, th:kt, under the same condition% tbe harder rail gives the slower wear. Of course, these comparisons are too few to enable us to arrive at positive ~?o-nclusions; but indications thus obtained are, I believe, fir more vsluitblc and tresttvc~rthy than those fhzt averages rvottld give us, mnde up from any ~lumhr of rails under intloy difi~rcal, conditions. Finally, it, seems to me, that the conclusions arrived at earlier in my remarks, together with, and confirmed by the last, show strong evidence that, under the same conditions, the harder rail will givc the slower wear. 0. C~~anute, New York CITY: We are very much shlipl, 1 ant sure, to Mr. Sandberg for his paper upn " Rail Ryaifications and Rail Inspertion in Europe." We have in thp United States bithhrto Been inspecting mils sonlewl~at haphazard, and we ore glad to gtbt tfie results of Mr. Sandberg's long experience. We recognize that he was an)ong the first, if not the very firwt, to iipply mare rittional and scientific rules to the designing of irou rails., niora recently, to adapt tlitve rules to the clesigtting of steel I':I~]R, to conform to the oapaljilities and rqniretnento of this new n1:ttcrial. Although we have generally adopted, in this country, sectinns for hteel rails which marly of our railway men think even bottar than those of Mr. Snlldlmrg, he is neverthelees the Ieat3er in foot.iito11~ we have followed ever since it has been est~blished

Jan 1, 1881

By N. A. D. Parlee

THE gas-liquid metal diffusion cell technique1-3 has been used to study the diffusion of nitrogen in Fe-C alloys. The actual apparatus and technique were the same as employed by the authors to study the diffusion of hydrogen in liquid iron.' The diffusion cell' was formed by immersing an alumina tube in a stagnant melt contained in an alumina crucible. The tube (hereafter called absorption tube) contained nitrogen gas at 1 atm and was connected to a sensitive gas-measuring system. The change in the average concentration of nitrogen in the melt in the absorption tube was determined by measuring the rate of absorption of nitrogen in the diffusion cell. Eq. [I], 1-3 derived from the appropriate solution of Fick's second law, was used to examine the data and to calculate chemical diffusion coefficients (D) in situations where the absorption appeared to be controlled by diffusion in the liquid: where V is the stp volume in cu cm, d is the diffusion cell diameter in cm, p, is the density of the melt in g per cu cm, pg is the stp density of nitrogen in g per cu cm, C, is expressed in wt pct, D is in sq cm per sec, and t is in min. According to Eq. [I], a plot of v vs vt should yield a straight line passing through the origin if absorption is controlled by diffusion in the liquid. The slope of this line could be used to determine the value of D under appropriate conditions. As discussed in earlier reports,1,2 the initial thermal expansion of the gas upon immersing the absorption tube distorts the line in the initial stages of a diffusion experiment. However, this is not a serious problem since the slope of V vs 6 plots can be determined from the data points obtained after the initial expansion ceases. The volumes reported on the data plot presented here represent absorption after this thermal expansion ceased. Several preliminary diffusion experiments were attempted with melts of pure iron and with Fe-C alloys containing up to 0.6 pct C. In these cases, no or very little absorption was observed. The only data obtained were for an Fe-C melt which was in addition thoroughly deoxidized by successive hydrogen and vacuum-degassing treatments. These treatments introduced an appreciable amount of aluminum into the melt and reduced its omgen content. The original charge material for this melt contained 0.23 pct s and approximately 0.001 pct &. After repeated hydrogen and vacuum-degassing treatments two diffusion experiments were performed. The analysis of the melt

Jan 1, 1968

By D. Turnbull, J. H. Hollomon, J. C. Fisher

UNDERSTANDING of the diffusion problem has recently been furthered by the analysis of Birchenall and Mehl.1 They pursued the problem of the variation of the diffusion coefficient with composition for non-ideal solid solutions. Their analysis follows the tradition of Wagner,2 Jost,3 Dehlinger,4 and Darken,' who assumed the net flux of dif¬fusing material to be proportional to the gradient of a quantity related to free energy. The basic assumption in Birchenall and Mehl's formulation of the problem is that the net flux of diffusing material is proportional to a thermodynamic activity gradient. To estimate the applicability of the derived relations, they corrected the diffusion coefficients of carbon in austenite by utilizing Smith's' activity data for carbon, and the diffusion coefficients for zinc in copper with activity data computed from the vapor pressure measurements of Hargreaves.7 The corrected coefficients for carbon were virtually independent of carbon concentration. For the diffusion of zinc in copper a moderate variation of diffusion coefficient with concentration remained after the correction. The problem of diffusion can be formulated in another way than that used by Birchenall and Mehl. The method is that of chemical rate theory and has been used by Eyring and his coworkers8,9 as well as by Eyring and Zwolinski10 in a discussion to Birchenall and Mehl's paper. As yet the method has not been applied to substitutional solid solutions. On the basis of their assumptions, Eyring and Zwolinski derived a relation between the diffusion coefficient and activity that is identical with that of Dehlinger and Darken but which does not correct for the variation of the diffusion coefficient with concentration as well as does the relation derived by Birchenall and Mehl. It was thought that the theory of diffusion would be more complete if the inconsistency between the two analyses could be rationalized and if diffusion in substitutional alloys were analyzed on the basis of the concepts of the chemical rate theory. CHEMICAL RATE THEORY According to the theory of absolute reaction rates8 the reaction [A,+A2+ ... +.A;->X,+X2 +...+X; EqI] is viewed as taking place in two steps. First the reactants A1, A2, . . . A[i] combine to form an activated complex M with which they are in equilibrium; [A, + A2 + .. . + Ai = M. Eq 2] Second the activated complex decomposes to give the products X1, X2. . .. X[j]; [M->X1+X2+ ... +.X;. Eq3] It has been shown8 that the number of activated complexes decomposing per unit volume per unit time is given by the expression† [kT]

Jan 1, 1948

By Warren L. Howes

LITERALLY hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be clues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations,1 grinding capacity usually is the greater consideration. GRINDING CAPACITY Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. [ ] From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell liners

Jan 1, 1945

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, H Pray, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941