Search Documents

By William G. Kegel

Problems involved in putting the gob back underground in modern deep mines we dealt with. In particular, the problems associated with haulage of the gob back to the mine, the blown gob method of dispersion underground, and handling the refuse as slurry are discussed. Some alternative methods of disposal are presented.

Jan 1, 1976

By A. F. Taggart, Nathaniel Arbiter

The chemical reaction occurring in collection of nonmetallic minerals with amine-type collectors was early postulated by students of flotation phenomena to be metathesis between the mineral and the collector, involving exchange between the amine-bearing (aminium) ion and the cation of the mineral, and formation at the mineral surface of an oriented film of the amine salt of the mineral anion. Qualitative evidence of exchange has been obtained on several occasions at Columbia. Thus 1000 C.C. of a solution containing 495 mg of laurylamine hydrochloride was shaken 17 min. with 100 grams of barite and ground in a porcelain mill to pass a 200-mesh screen; the mixture was then set aside for 48 hr. Filtrate therefrom analyzed 476 mg. per liter of laurylamine hydrochloride. There was no substantial loss of chloride ion (78.4 mg. per liter in the original; 74 in the filtrate). No successful analyses were concluded for barium ion. Earlier, confessedly rough work with scheelite indicated a solution gain in Ca++ equivalent to about one-half the aminium ion lost. Real quantitative roof of the exchange, in the form of an established stoichiometric balance, is unknown to the authors. The data of the present paper, however, obtained from experiments designed on the basis of the exchange hypothesis, constitute strong evidence of its truth, and at the same time point the way to economic utilization of the expensive nitrogen-bearing collectors in concentration of the low-priced nonmetallic minerals. The basic postulate underlying the experiments performed was that, if the collecting reaction is of the type R+ + Y- + MX = RX + M+ + Y- where R = aminium ion, Y = the anion of the amine salt, and M and X are, respectively, the cation and anion of the mineral, the reaction should obey qualitatively the implications of the mass-action and solubility-product laws. This is to say that coating and collection should be aided by the addition to the solution of either ion (R+ or X-) of the collector-coating compound, and hindered by the addition of either of the ions M+ or y-. Experimental work comprised determination of (,) the relative solubilities of the laurylammonium salts of a variety of nonmetallic-mineral anions; and (21 the contact angles' of various minerals in solutions containing different concentrations of the postulated controlling ions. Semiquantitative flotation tests were run With barite as checks on the diagnostic character of the contact angles. The amine

Jan 1, 1947

By Basil Prescott

In the science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each SUCcessful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation. More Romance than Developed Ore in Limestone Deposits In certain types of deposits, methods little known 25 yews ago have been developed, perfected and standardized to a degree that lifts sampling from the field of manual labor to the plane of an applied science; for instance, the modern methods of estimating the so-called porphyry coppers. With some types of orebodies, we have become familiar, and sometimes on too easy speaking terms, with millions of tons of ore in reserve and tens of millions of dollars; while with others even these once marvelous figures sink into insignificance before the array of ciphers that are presented. .In such company, the average limestone replacement orebody is entirely out of place, for its reserves seldom reach a figure to arrest the attention of the modern engineer, and more often are insignificant. It is only when the records of the production of some of the older camps are studied, which show them to have continuously produced over very extended periods, that a realization is borne home that occasionally this type is worthy of consideration even in these days of gigantic tonnage.

Jan 1, 1925

By Nathaniel Arbiter, A. F. Taggart

The chemical reaction occurring in collection of nonmetallic minerals with amine-type collectors was early postulated by students of flotation phenomena to be metathesis between the mineral and the collector, involving exchange between the amine-bearing (aminium) ion and the cation of the mineral, and formation at the mineral surface of an oriented film of the amine salt of the mineral anion. Qualitative evidence of exchange has been obtained on several occasions at Columbia. Thus 1000 C.C. of a solution containing 495 mg of laurylamine hydrochloride was shaken 17 min. with 100 grams of barite and ground in a porcelain mill to pass a 200-mesh screen; the mixture was then set aside for 48 hr. Filtrate therefrom analyzed 476 mg. per liter of laurylamine hydrochloride. There was no substantial loss of chloride ion (78.4 mg. per liter in the original; 74 in the filtrate). No successful analyses were concluded for barium ion. Earlier, confessedly rough work with scheelite indicated a solution gain in Ca++ equivalent to about one-half the aminium ion lost. Real quantitative roof of the exchange, in the form of an established stoichiometric balance, is unknown to the authors. The data of the present paper, however, obtained from experiments designed on the basis of the exchange hypothesis, constitute strong evidence of its truth, and at the same time point the way to economic utilization of the expensive nitrogen-bearing collectors in concentration of the low-priced nonmetallic minerals. The basic postulate underlying the experiments performed was that, if the collecting reaction is of the type R+ + Y- + MX = RX + M+ + Y- where R = aminium ion, Y = the anion of the amine salt, and M and X are, respectively, the cation and anion of the mineral, the reaction should obey qualitatively the implications of the mass-action and solubility-product laws. This is to say that coating and collection should be aided by the addition to the solution of either ion (R+ or X-) of the collector-coating compound, and hindered by the addition of either of the ions M+ or y-. Experimental work comprised determination of (,) the relative solubilities of the laurylammonium salts of a variety of nonmetallic-mineral anions; and (21 the contact angles' of various minerals in solutions containing different concentrations of the postulated controlling ions. Semiquantitative flotation tests were run With barite as checks on the diagnostic character of the contact angles. The amine

Jan 1, 1947

By Charles H. J. Patterson

When coal is deposited on the decks of pneumatic tables, all fine particles clinging to the larger pieces are blown free by the air. Inasmuch as the air retains an appreciable residual velocity after passing through the bed of coal, it is capable of suspending particles of goodly size. This velocity is dissipated gradually and, unless confined, can readily extend beyond the limits of the plant. Today the ideal in the design and operation of pneumatic cleaning plants is not that they be no dustier than the ordinary tipple, but rather that they be as clean as an office or shop. This degree of perfection may not yet have been attained in any commercial plant, but it is not impossible of achievement. Not until recently has the recirculation principle been applied to pneumatic separating plants. In the writer's estimation, it has not yet been proved entirely satisfactory in commercial installations. A serious obstacle lies in the fact that it is practically impossible to provide a truly closed circuit. The air circuits must be interrupted at certain points, if only for the introduction of raw material and for the recovery of the finished product. It is feasible to prevent the escape of polluted air at these points, but this can scarcely be accomplished without admitting additional air into the circuit. These additions of air are cumulative, which necessitates means for emitting to the atmosphere the excess while still carrying its objectionable burden, if provisions are not made for conditioning. If it must be provided at all, conditioning is frequently simpler and more economical if applied to the entire volume of air involved. This procedure eliminates the extra initial cost and operating expense of the closed system. Crane Cheek Experiments The first noteworthy commercial installation of pneumatic equipment was made in 1922, at the Crane Creek plant of the American Coal Co. of Allegheny County, at McComas, W. Va. Six tables for cleaning coal between the limits of and 3 in. comprised the initial installation. Dust was collected by hoods connected by a system of ducts to exhauster fans. In this installation the unit dust burden was small, owing to the removal of fines from the feed by vibrating screens.

Jan 1, 1931

By R. E. Ogilvie, N. L. Peterson

Intevdiffusion and intrinsic diffusiorz coefficients were determined in the uranium-niobium system from diffusion couples analyzed with an electron microbeam probe. A Previously unveported intermediate phase, designated in this report as the delta phase, was found to exist along the mobium-rich side of the miscibility gap. Its composition width was determined from the concentration gradients in the diffusion couples. The presence of this phase was also confirmed by microhardness analysis and metallographic observations. THE excellent corrosion resistant properties, high-temperature strength and reasonable nuclear properties of niobium have prompted its use as an alloying element with uranium and as a possible cladding material for reactor fuel elements. Hence the formation and growth of intermetallic phases as well as diffusion data for the uranium-niobium system are of considerable practical importance to metallurgists and nuclear engineers. Diffusion zones may exhibit varying degrees of complexity dependi.ng upon the mutual solubility of the metals involved, and the intermediate phases which may form. In the simplest case where the metals exhibit a calmplete range of solid solubility, a single phase region is produced. Generally, however, the metals may react to produce a multiphase diffusion zone containing several layers of intermetallic phases. A number of investigatorsl-6 have analyzed the concentration gradients present in diffusion couples in order to investigate phase equilibria and solu- bility limits. If diffusion is the rate-controlling process in establishing a concentration gradient, the compositions at the interfaces of the intermediate phases will represent the equilibrium values expected from the phase diagram at the temperature at which diffusion has taken place. No published information is available at this time on diffusion in the uranium-niobium system. A number of investigators7-" have contributed information to the construction of the uranium-niobium phase diagram from other than diffusion techniques. There is good agreement on the high uranium side of the phase diagram, but the high niobium side of the miscibility gap still remains somewhat in doubt. The phase diagram as determined by B. A. Rogers, et al.7 is shown in Fig. 1. The present work was aimed at obtaining fundamental information about the solubility limits of the miscibility gap and diffusion in the uranium-niobium system. A Kirkendall effect, which might be expected on the basis of the rather large difference in melting points between uranium (1132°C) and niobium (2415" C), was also investigated. The concentration gradients were measured by an electron microbeam probe technique, similar to that used by Castaing,l2 Adda and philibert,13, l4 and Macres.4

Jan 1, 1961

By H. E. Stauss, E. I. Salkovitz, F. W. von Batchelder

EXISTING information regarding the structure of a spherulite in nodular cast iron is based on optical studies. According to these data, a nodule consists of an aggregate of graphite crystallites radiating from the center, with the closely packed basal planes at right angles to the radii. The c axes lie along the radii. This view faces some uncertainty in the fact that the c axis does not represent the accepted direction of fastest growth in graphite. To supplement the optical information, X-ray studies have now been made. The principle used was to screen the nodule in greater part from the X-ray beam and expose only a minor cap. As successively larger portions of the nodule were introduced into the X-ray beam, any differences in the X-ray patterns could be observed. Such photographs have been taken with chromium radiation and a Laue camera. The graphite nodule itself, about 0.010 to 0.025 in. in diam, was mounted with vaseline on a micrometer screw for control of the linear motion. The nodule rotated about 45" each time that it was translated linearly. The nodules were obtained from magnesium-treated hypereutectic iron by electrolytic solution of the iron in hydrochloric acid. In Fig. la is shown the pattern of the thinnest cap examined. In Fig. lb is shown the pattern of the same nodule moved 0.003 in. farther into the X-ray beam, and rotated 45" at the same time. Figs, la and lb indicate incomplete circles for graphite (the two outer circles arise from graphite) with the side arcs much weaker than the top and bottom ones. The arcs obtained are themselves not continuous in intensity but vary with maxima of intensity some 15" and 30" apart. The structure of the nodule that would give rise to such a pattern can be explained as follows. Basically the nodule consisted of small crystallites. The discontinuous character of the diffraction rings demonstrates that the nodule was not composed of randomly oriented crystallites. The strong vertical reflections and the weak lateral reflections show that the reflecting planes were roughly normal to the radii. The absence of sharp reflection spots suggests that the nodule did not contain large crystals. The sharpness of the diffraction rings in their radial direction shows that the variations in intensity along the arcs were not the result of line broadening resulting from extremely small crystals. In the diffraction patterns two rings corresponding to graphite were found. The third and inner ring in the figures originated in the vaseline. The graphite rings correspond to the a and ß lines reflected from the basal planes, showing that the radii of the nodules are the [0001] direction normal to the basal planes of graphite. The picture of the structure that is formed is, therefore, one of aggregates of crystallites. Within each aggregate the c axes of the crystallites tend to align themselves in the radial direction of the nodule, although these axes deviate somewhat in direction by a continuous variation of angle. Correspondingly the basal planes of the graphite crystallites are generally normal to the radii. It is a pleasure to acknowledge the assistance of M. C. Bloom and R. P. Dunphy of this laboratory.

Jan 1, 1952

By C. A. Edwards

Following a brief introduction, an outline is given of the four main conditions in which gases may be associated with metals; namely, (1) adsorbed gases, (2) dissolved gases, (3) gases in chemical combination, (4) gases entrapped in blowholes or cavities. Adsorption is essentially a surface phenomenon and is regarded as the attachment of outside molecules or atoms to the exposed free valencies of the atoms comprising the surface layers. In many cases where adsorbed films of gas are formed this is accompanied by a process of diffusion of the gas into the metal itself. This is particularly true in respect to iron and hydrogen, and experiments have shown that there is no difference between the rate at which hydrogen diffuses through a single crystal of iron arid through the same material after it has been recrystal-lized into a mass of small crystals. This does not prevent a somewhat greater concentration of gas at the boundaries of adjacent crystals, nor does it mean that the effect of the gas will be the same at the boundaries as it is within the body of the crystals. Indeed, under certain conditions, iron is rendered very brittle at the crystal boundaries, as shown in experiments by Pfeil with samples of almost pure iron. Much work has been done by many investigators concerning the temperature and conditions under which dissolved hydrogen, in particular, can be at least partially removed from different metals. With iron, the hydrogen that has diffused into the metal as a result of acid attack by pickling or by electrolytic deposition of the gas on the metal is partly removed by exposing the metal to the atmosphere at ordinary temperatures. Considerably more can be eliminated by raising the temperature, and even greater quantities by jointly raising the temperature and reducing the pressure. Annealing at suitable temperatures completely removes the bad effects of excessive mounts of hydrogen dissolved in or associated with iron. This is shown by the data plotted in Fig. 1, giving values for electrolytic iron sheets after annealing at temperatures between 250" and 950" C. The hydrogen brittleness is rapidly diminished at

Jan 1, 1935

By C. A. Edwards

Following a brief introduction, an outline is given of the four main conditions in which gases may be associated with metals; namely, (1) adsorbed gases, (2) dissolved gases, (3) gases in chemical combination, (4) gases entrapped in blowholes or cavities. Adsorption is essentially a surface phenomenon and is regarded as the attachment of outside molecules or atoms to the exposed free valencies of the atoms comprising the surface layers. In many cases where adsorbed films of gas are formed this is accompanied by a process of diffusion of the gas into the metal itself. This is particularly true in respect to iron and hydrogen, and experiments have shown that there is no difference between the rate at which hydrogen diffuses through a single crystal of iron arid through the same material after it has been recrystal-lized into a mass of small crystals. This does not prevent a somewhat greater concentration of gas at the boundaries of adjacent crystals, nor does it mean that the effect of the gas will be the same at the boundaries as it is within the body of the crystals. Indeed, under certain conditions, iron is rendered very brittle at the crystal boundaries, as shown in experiments by Pfeil with samples of almost pure iron. Much work has been done by many investigators concerning the temperature and conditions under which dissolved hydrogen, in particular, can be at least partially removed from different metals. With iron, the hydrogen that has diffused into the metal as a result of acid attack by pickling or by electrolytic deposition of the gas on the metal is partly removed by exposing the metal to the atmosphere at ordinary temperatures. Considerably more can be eliminated by raising the temperature, and even greater quantities by jointly raising the temperature and reducing the pressure. Annealing at suitable temperatures completely removes the bad effects of excessive mounts of hydrogen dissolved in or associated with iron. This is shown by the data plotted in Fig. 1, giving values for electrolytic iron sheets after annealing at temperatures between 250" and 950" C. The hydrogen brittleness is rapidly diminished at

Jan 1, 1935

By J. L. Huitt

Some of the problems associated with the acid treatment of oil wells are related to the control of the composition of formation treating acid. One test usually made at the well site is the determination of the acid concentration. Heretofore, the concentration of the acid delivered to the well site usually has been interpreted from a hydrometer measurement of the specific gravity of the acid solution. Experience has shown that this indirect measurement of acid concentration can give erroneous results. More reliable results are, of course, obtainable by the titration method; however, this method is not easily adapted to well-site testing. To overcome these objections, a device was developed for use in the field which permits determination of the concentration of treating acid both quickly and accurately at the time of the acid treatment. Its purpose was three-fold, namely, to determine: (1) the concentration of the fresh treating acid, (2) the concentration of the spent acid returning from the well, and (3) the solubility of formation samples in treating acid. The device was designed to operate on the principle of the stoichiometric relation between the calcium carbonate—hydrochloric acid reaction and the carbon dioxide gas resulting from the reaction. By confining the carbon dioxide gas within a reaction cell of the type shown in Fig. 1, the pressure inside the cell is increased. Since the pressure is an indication of the quantity of carbon dioxide gas produced, it may be used to estimate the concentration of the acid, provided an excess of calcium carbonate is used. From information on the volume of the reaction cell, the volume of acid used, and the pressure and temperature of the gas after the completion of the reaction, the concentration of the treating acid may be computed. The reaction cell is essentially a pressure vessel equipped with a pressure gage, temperature indicator. pressure release valve, and a special sample holder. Plastic and metal construction makes the cell both rugged and acid-resistant. The sample holder is so designed that a sample of calcium carbonate (or sample of carbonate rock) can be dropped into the acid

Jan 1, 1956

By James Terry Duee

No important producing developments took place in Colombia during the year 1928. This was at least partly due to the paralysis of operations by the passage, during the latter part of 1927, of a law which was regarded by the oil companies as confiscatory and unjust, and the promulgation of exceedingly stringent regulations of this law under decree No. 150, published Jan. 28, 1928. This decree, which contained 24 articles, practically prevented not only producing operations by the oil companies but even such activities as geological explorations and surveying, as severe fines were imposed for the possession of maps not registered with the Ministry of Industries. Both this regulatory decree and the law were subject to attack in the courts by several of the oil companies. The regulatory decree was suspended May 22 by Presidential proclamation, until the suits against it are decided by the Supreme Court and Council of State. Though another law was introduced into the Colombian Congress at a later date, no action was taken on it, and at the time of the writing of this paper, it would appear that no oil bill will pass the Colombian Congress during the present session. The Barco concession, which was revoked in February, 1926, still continues an unsettled matter, although there have been rumors that the government was attempting to come to some decision on this rather difficult question. A hopeful sign toward the close of the year was the settlement of negotiations with the Tropical Oil Co. over the acceptance of the payment for royalties due the government from that company. This settlement, which covered a royalty on crude oil produced from June 30, 1926 to June 30, 1928, represented a cash payment for approximately 3,000,000 barrels. It is to be hoped that during the coming year the Colombian government will see its way clear to clarify its position on petroleum legislation. A good augury for the future was the statement made by President Abadia Mendez on New Year's Day, in which he courageously admitted the errors of previous legislation and said, regarding oil, "Very soon

Jan 1, 1929

By C. V. Milikan

Allocation of allowed production in a prorated field by the use of bottom-hole pressures is a method which is sound in theory. Thus far it has had limited application because the experience in correlating bottom-hole pressures with the depletion of wells or fields is not sufficient to interpret all the pressure changes. With additional data and more general knowledge of bottom-hole pressures their use in proration will probably become common. Bottom-hole pressure is the pressure at or near the bottom of a well. It is usually determined at the face of the producing horizon. Bottom-hole pressure measured while the well is producing, may be called the bottom-hole producing pressure or bottom-hole flowing pressure. If the well has been shut in or shut down long enough for the pressure in the producing horizon within the drainage area of the well to equalize, it may be called the reservoir pressure. The allowable production from a prorated field may be allocated to the individual wells or leases by three methods: 1. Bottom-hole producing or flowing pressures. (a) The potential capacity of a well to produce. (b) A uniform differential pressure while producing at the allowed rate. 2. Reservoir pressures. 3. A combination of bottom-hole producing pressures and reservoir pressures. In most prorated fields the allowed production is allocated to the individual wells or leases in proportion to their individual potentials. This method is based on the theory that there is a direct relationship between the permeability and the porosity of the reservoir. More directly stated it means that there is a direct relationship between the amount of oil in the reservoir and the rate at which it will move through the reservoir. While in general this relationship is true, it may vary considerably in different wells. Furthermore, in many wells the capacity of the reservoir to deliver oil to the well is greater than the capacity of the flow string to deliver oil to the surface. It is especially true where the potential is determined by flowing through tubing or by pumping.

Jan 1, 1933

By David N. French

In a recent paper, Miyoshi, Hara, and sugimotoL have shown that hardness increases and crack resistance decreases with polishing time in tungsten car-bide-cobalt alloys. They attribute the changes in hardness and crack resistance to cold working in these alloys. More recently Exner2 explains the decrease in crack resistance with the amount of material removed (polishing time) by suggesting that polishing removes a high compressive residual surface stress due to the initial grinding operation. He cites previous work on steel to show grinding can induce surface compressive stresses but offers no direct experimental measurements to support this in cemented tungsten carbides. In recent work we have observed changes in residual stress in the W C phase as measured by X-ray diffraction techniques with changes in polishing conditions.3 As a result of the work of Miyoshi et al.,L a brief study was undertaken to investigate the effects of polishing and grinding on the residual stress in the WC phase and have been reported.4 A single composition of tungsten carbide —10 wt pct Co was used. Two initial conditions were studied: an annealed condition with about -30,000 psi residual stress from the differences in thermal coefficients of expansion of WC and cobalt and, on the same specimen, a surface ground with a 150 grit diamond wheel. Stress was measured in the WC phase using X-ray diffractometry as a function of the amount of material removed by metallographic polishing with 6 diamond paste. The results are shown in Fig. 1. Two things are noted, 1) polishing with 6 p diamond paste has little effect on the annealed sample and 2) the magnitude of the grinding stress is markedly reduced as material is removed. By the time 0.1 mil is removed the surface has a metallographic polish satisfactory for light microscopy examination. Thus the surface, even though polished, can still retain most of the stress due to grinding. Since WC is itself slightly ductile, it seems reasonable that high compressive stresses can be generated in the surface by the plastic deformation accompanying grinding. Exner2 suggests, by analogy with steel, that as a result of grinding both WC and cobalt in the

Jan 1, 1970

By Roger Holmberg, Kenneth Mäki

This paper describe; open pit studies where blasting damage introduced in the remaining rock has been investigated. Results from two open pit mines are described and discussed. Parallel performed laboratory experiments, where simulated blasting damage has been introduced into samples before shear strength testing took place, are also reviewed. These studies are tied together in order to throw some light upon how the blasting damage influences the slope stability. A mathematical model is also described which will make it possible to optimize the blast design for a specified damage zone in the rock mass.

Jan 1, 1983

By Arthur Young

UNEMPLOYMENT no longer finds its cure in pros-perity. Not only is there surplus labor in over-developed industries -like coal -mining, but more and more man, power is being released by technical im-provements in production. A new problem in industry has arisen: What is to be done with the labor dis-pensed with by better methods and more highly de-veloped equipment? Are luxury industries the logical outlet for our new unemployed? There has been a marked decline in employment in the manufacturing industries during 1927. Its extent is shown by the Bureau of Labor Statistics index, which receded from a high of 91.4 in March to 87.3 in October, with an estimated figure of approximately 85 in De-cember. This was a drop between the high and low points in the year of about 7 per cent, which means roughly that at the close of 1927 there were approxi-mately 600,000 fewer persons employed in manufac-turing industries than in March -of 1927, and upward of 400,000 less than in December, 1926. Does this de-cline reflect a swing toward industrial depression? Paradoxically it does not; the cause of unemployment at this time does not lie in a lack of prosperity, but rather is largely traceable to prosperity. Capital has been abundant and has gone back into production in the form of great increases in mechanization and new processing. Management is more than ever on the alert to improve methods, as well as to cut costs through reduction of personnel. Properly applied incentives and employee cooperation also have increased produc-tion per man. A new phenomenon in the industrial world-technological unemployment-is the result. Of course, there are added to those unemployed be-cause of the reasons just considered those affected by the coal strike, the period of shutdown at the Ford plants, and the reduction in expenditures by railroads and public utilities. This whole situation suggests that the problem of unemployment is not entirely solved by ironing out seasonal variations or by achieving business prosperity.

Jan 1, 1928

By Lynn Howell

IN a previous articles we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon Which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in 'the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.' Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added. inside the chamber, This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously, Briefly described, the chamber moving in the hole is made of 3,2-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft, long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber, Above this is the vacuum-tube amplifier with its batteries and transformer, In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube, Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1939

Jan 1, 1906

Jan 1, 1957

By C. J. Delisio

The basic concept of tunnel boring has not changed since the late 1800's. R. Stanley of Great Britain obtained a Canadian patent as early as December 1891. Mr. Stanley's machine was a device that consisted of a rotating wheel equipped with drag-type teeth; it had a means of thrusting the cutterhead against the face or heading; it had a means of clamping or gripping the machine in its bore; it had a means of collecting and depositing the cuttings into a screw-type conveyor located near the invert of the tunnel. It even had a means of varying the speed of the forward motion of the machine to suit different hardnesses of rock encountered. This description essentially fits the latest tunnel-boring machines being built today. In short, there has been no significant advance in the basic concept in 70 to 80 years. It may well be that no significant change can be expected for some time into the future. Today's machines, while still basic in concept, offer many advances aimed at faster tunneling. Among these are 1 ) improved cutters, 2) guidance and steering devices, 3) dust-control devices, and 4) mechanisms to aid in installing tunnel supports. CUTTERS The most important part of a hard-rock tunnel borer is the cutter. If the cutter can cut the rock, it is a boring machine. If the cutter cannot cut the rock, no other part of the machine can. When Jarva, Inc. decided to build a machine, the first problem was to find a good cutter. In our search, we looked at most of the cutters on the market. We selected Reed Drilling Tools' cutter because the design of their cutter was aimed at hard-rock tunneling. We feel that they build the best cutter available and provide the best possible service to their customers. As tunnel-boring machine design advanced, the transition from drag bits to roller bits was natural because harder formations required a roller bit, and it is the goal of all mole users to bore harder formations. Roller bits

Jan 1, 1970