Search Documents

By Gordon B. French

Occidental's in situ retorting process for oil shale has many advantages over the conventional, underground mine and surface retort. Only a portion of the oil shale is mined and transported outside where it blends with the oil-shale talus found in the area. Spent shale is retained underground without surface disposal problems. The process consumes no water from outside sources. Noise and dust levels are kept at a minimum. As many of the facilities as possible are located underground. More oil is produced from a given area than conventional surface processing. Additional energy can be recovered by using conventional turbines to generate electrical power of magnitude of three to four times required by the operation.

Jan 1, 1977

By Fredrick Laist, J. P. Cooper

In the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feeding arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged. It was expected that the shaft would considerably increase the capacity of the reverberatory and that a better fuel ratio would be obtained on account of the high temperature at which the calcines would enter the

Jan 1, 1934

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large. Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton acid Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, 111. All three have water conditions that make it necessary to regularly seal off till worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will he included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By E. J. Wasp, T. C. Aude, F. B. Raymer

The following paper deals with technical aspects of terminal facilities for western coal pipelines. The information is taken from the Ohio and Black Mesa pipelines and the proposed one in Wyoming. This paper first discusses the feed terminal, the product that it must produce, and the reasons for coal cleaning. Then in the delivery terminal section, the various methods of dewatering the coal and some recent innovative ideas on bunkering the dewatered product and storing the dewatered coal in large outdoor piles are discussed.

Jan 1, 1979

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By Robert Tally

UNDERGROUND fires have been common in the mines of the United Verde Copper Co. for the past 22 years. The first fire started in the 300 Hampton stope in the fall of 1894, following a cave in that orebody. The soft and highly pyritic nature of the ores is responsible for most of these fires. Since ore characteristics, methods of mining and ventilation, have an important influence on mine fires, they will be described in this paper. Orebodies The ores are mostly chalcopyrite except on the upper levels where considerable chalcocite, black oxides and other secondary minerals occur. The orebodies are in the form of lenses and vary in size. Some are small, while others are several hundred feet in length by a hundred or more feet in width. These orebodies extend, in some cases, from the surface to the lowest levels of the mine and usually at a steep angle of inclination. There are three different classes of ores, classified in accordance with the gangue rock. The copper in all cases, except as above specified, is in the form of chalcopyrite. The largest and most important of these reserves are in a pyrite gangue. Next in order of importance are the schist ores and lastly the quartz porphyries. The pyrite, locally termed iron ores, average from 30 to 42 per cent. sulphur. The schist and quartz, porphyries vary from 3 to 25 per cent. sulphur. Mining Methods All the orebodies were worked by the overhand square-set method of mining prior to 1908; since then the cut-and-fill, shrinkage and mill-hole systems have been largely employed. But 15 per cent. of the total tonnage now extracted is from timbered stopes. Most off this is from the upper levels where the ore is soft, heavy and more or less broken to the surface. Large reserves of these ores are being conserved for more efficient methods of mining.

Jan 9, 1916

By Charles B. Dudley

In view of various papers and discussion.;, at recent meetings of the Institute, upon testing, methods of testing, inspectors, inspection and specifications, it has occurred to me that my experience of some fifteen years, in the making and enforcement of specifications, in connection with the Motive Power Department of the Pennsylvania Railroad, might give some value to the few suggestions offered in this paper. There is friction, not to say antagonism, between the producers and the consumers of structural materials. On the one hand, the producers complain of the severity of inspection, or the lack of knowledge and want of good judgment on the part of inspectors, and, indeed, have gone so far as to suggest the abolition of the whole scheme of inspecting and testing materials. On the other hand, the consumers are, apparently, more and more relying on specifications

Jan 1, 1893

By AIME AIME

ORGANIZATION of The Federated American Engineering Societies was effected at the organizing conference of national, local, state and regional engineering and allied technical organizations at the Cosmos Club, Washington, D. C., June 3 and 4. Thus is brought into being the greatest national engineering society in the world. The object of the organization is to further the interests of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to engineering and allied technical professions. Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization. The constitution as adopted by the conference, calls for the creation of s managing body to be known as the American Engineering Council, and its executive board. The belief was expressed that the entire organization would come to be spoken of as the American Engineering Council. The council is to coordinate the activities of state councils and of local affiliations whenever these activities are of national or general importance or may affect the general interests of engineers. Representation in the council is to be according to membership of the component societies.

Jan 1, 1920

By K. L. Meissner

It is well known that the so-called pure aluminum contains noticeable amounts of impurities, chiefly iron and silicon, and many investigators have studied the forms in which these impurities exist. Hanson and Archbutt1 state that iron exists in aluminum as FeA13 and silicon as elementary Si. The solubility of FeA13 in solid aluminum is practically zero, or at least so small that the smallest trace of this compound is always visible as a separate constituent. Under the microscope an untrained eye can hardly distinguish, without etching, the two constituents FeA13 and Si, but they can be differentiated by suitable etching reagents. Anderson2 also found the same results. At the same time, Merica, Waltenberg, and Freeman3 found a constituent of unknown composition. They found a small thermal effect, at 610" C., on the cooling curves of aluminum with small amounts of iron and silicon. The intensity of this effect increased with increasing silicon content, until an effect occurred at 576" C. due to the eutectic between aluminum and silicon. The authors ascribed the effect at 610" C. to a compound, which they call "X constituent." It was thought to be a ternary compound containing iron and silicon and could be observed under the microscope as dark particles. Dix4 has published unetched photomicrographs of an aluminum with 0.51 per cent. iron, 0.99 per cent. silicon, and 0.32 per cent. copper that shows three constituents: the dark Si (black in the figure), the lighter FeA13, which appears in half tone and crystallizes in needles, and a constituent of the same color as FeAL3 but of different crystal form, often resembling Chinese script. This last constituent, Dix thought, is a compound of Fe and Si; not the compound FeSi but a compound containing a relatively small amount of silicon. Therefore an alloy of aluminum. iron, and silicon (the copper should not be regarded in the following considerations) must contain the following four constituents: Al, FeA13, Si, and a compound of Fe and Si. This, however, does not agree with the laws of chemical equilibrium.

Jan 1, 1926

By G. S. Hume

Petroleum is produced in Canada in the provinces of New Brunswick, Ontario and Alberta and in the Northwest Territories. The total production, however, is relatively small in comparison with the consumption, the value of imports exceeding 40 million dollars a year. Production figures are given in Tables 1 and 2. In Turner Valley, still the largest producing gas and oil field in Canada, five wells were completed during the year. The largest of these

Jan 1, 1936

By G. S. Hume

Petroleum is produced in Canada in the provinces of New Brunswick, Ontario and Alberta and in the Northwest Territories. The total production, however, is relatively small in comparison with the consumption, the value of imports exceeding 40 million dollars a year. Production figures are given in Tables 1 and 2. In Turner Valley, still the largest producing gas and oil field in Canada, five wells were completed during the year. The largest of these

Jan 1, 1936

By Calvin C. Brown, John Bigando

Pit slopes at Cananea commonly vary from 50-55°, and some have been standing for over 25 years. Their maximum vertical extent is 700 ft. Investigation of these slopes and the rocks of which they are composed has led to the decision to experiment with final pit slope angles of up to 70". Precision blasting to obtain a smooth final pit wall with minimum raveling is an integral part of this field experiment. Presplitting, one of the precision blasting techniques, requires the drilling of a single row of holes along the limit of a pre- designed excavation. The hole spacings and charge concentrations must be experimentally determined in the field, using published data as a base (Table 1). The holes are fired prior to the main round and carry no burden and therefore produce no broken rock. Thus, it is an operational cost with no direct return on investment.

Jan 9, 1972

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers ' and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1944

By Fred H. Lippold, Wm. H. Wolf

Methods of fair payment for excavating, supporting, and concrete lining tunnels have been sought by various owners for years. Tunneling techniques have changed with the development of equipment-from the hand-mucking operation to the machine mucker and, most recently, to machine-boring; from tunnel supports using timber sets to steel sets to rock bolts and, most recently, to shotcrete support; and from hand-placing the concrete lining using wooden forms to pumping or pneumatic placing using steel forms. As tunnel construction techniques advanced, so did methods for payment for the work performed. The recent development of tunnel-boring machines, or "moles," is precipitating another change. These changes have led to some difficulty in providing proper payment for the various items of work for different types of tunnels. As a major construction agency engaged in water-resources development in the western states, the U.S. Bureau of Reclamation has long been aware of the need for clarification of payment provisions in tunnel construction. The Bureau has some 150 miles of tunnels completed on its projects and about 50 miles of tunnels under construction. In this construction, the Bureau has benefited by the advance made by contractors in improving the techniques of tunnel excavation. To assure that the Bureau has an up-to-date approach to payment provisions, the Chief Engineer recently established a "standard" method of payment for all types of tunnels. It is believed that this new method of payment will be equitable for all contractors bidding on various types of tunnels using the diversity of methods of excavation now available to them. These payment provisions provide for different quantities for excavated tunnels using the blasting technique or using machine-boring techniques. In this way, the contractors have a choice in excavation methods and an equal opportunity to be low in their bids. We believe this will be an incentive to all contractors to be as progressive as the development of new equipment economically allows.

Jan 1, 1970

By W. G. Matteson

IN 1915, the State of California passed a law of great scope and importance. This law has been in successful operation for., year and may be briefly described as an act "establishing and creating a department of. the State Mining Bureau for the protection of the natural resources of petroleum and gas from waste and destruction through improper operations in production; providing for the inspection of petroleum and gas wells; requiring all persons operating petroleum and gas wells to make certain reports" and providing the necessary officers and assessments-to carry out the provisions of the act. The statute provides for a separate department of the State Mining Bureau, under the general supervision of the State mineralogist, with a staff composed of a "state oil and gas supervisor" and four deputies. It rules that all petroleum and natural gas wells shall be drilled, operated or abandoned under the supervision of the State supervisor, who shall order such tests or remedial work as seems to him necessary to protect the interests of property owners and the general public. It also provides for a board of arbitration to consider orders given by the supervisor which are not acceptable to the well owner. Section 18 of the, act, which is the provision that is directly related to, this paper, requires "the owner of any well referred to in this act to keep a careful and accurate log of the drilling of such well;" and further requires that this log shall show the character and depth of the formations passed through or encountered in the drilling, particularly the location and depth of the water-bearing strata; the character of the water encountered (so far as ascertained); whether the water was shut off, and, if so, at what point; that it shall show completely the amounts, kinds and size of casing used; the depth at which oil-bearing strata are encountered; the depth and character of the strata, and whether all water was successfully and permanently shut off so as to prevent percolation or penetration into the oil-bearing strata. -

Jan 2, 1917

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By C. B. Manula, R. Venkataramani, T. V. Falkie

A linear programming model has been developed to solve a production planning problem for a multi-plant stone operation serving several customers. The factors considered are production capacities, inventory restrictions, demand requirements, and available stone reserves. The objective function to be optimized is the total annual net returns from the quarry operations. For the purposes of model testing, annual stone sales from each plant were divided monthwise, productwise, and assigned to a market. The concept of assigning demands to market sectors and not to any particular plant creates the self-correcting interplay between the plants and the markets. Along with the inventory restrictions, and ending inventory requirements, this interaction enables the model to minimize the external diseconomics. The model was tested against an operating prototype and a number of alternative problems were also considered. Finally, the basic linear programming model has been enlarged by the addition of another dimension and the problem has been derived in a decomposition format.

Jan 1, 1972

By Eugene P. Pfleider, Claus Freyberger

Generally, the different methods of financing new mining projects are not well understood by the engineers and supervisory personnel. Nor are the effects of these alternatives on depletion, taxes and profitability readily apparent to even the sophisticated management personnel without the aid of cash flow studies. Fortunately, with the advent of the computer it is possible now to simulate many different combinations of 1) equity, 2) loan and 3) production payment financing with little effort. A general computer program for cash flow analysis of mining ventures has been developed and applied as a case example to a 1967 feasibility study of the Underground Mining of Minnesota Taconite. The effects on profitability as measured both in rates-of-return and present value are presented for various financing combinations. In addition, percentage depletion rates were altered so as to measure the impact of this statuatory allowance. Based on the cost data as presented in the aforementioned 1967 feasibility study, and assuming 7% loans, the rates-of-return vary from 9. 9% to [00] % on equity variations and from 9. 9% to 11.4% on total invested funds.

Jan 1, 1969