Search Documents

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

Jan 1, 1961

By J. L. Taylor, P. Duwez

PARTIAL phase diagrams of titanium with iron, cobalt, and nickel have been established by previous investigators.1-3 These diagrams seem to be reliable, at least for concentrations of titanium ranging from 0 to about 50 at. pct. More recently, Long and his collaborators have presented a tentative titanium-nickel diagram covering the titanium-rich side.' These various studies indicate that in each system three intermediate phases exist and correspond to the compositions Tia, TiX, and TiX2 (or TiX3). The purpose of this paper is to review the available information on the crystal structure of these phases and to give the results of additional X-ray diffraction studies. Previous Work A summary of the work of Wallbaum and his collaborators"-' is presented in table I. The first intermediate phase on the titanium-rich side of the three systems, with iron, cobalt, and nickel, is of the Ti2X type and has a face-centered cubic structure. Although it is stated that the unit cell contains 96 atoms: no lattice parameters are given. The second phase is centered around the compositions TiX for the three systems. The crystal structure of this phase is mentioned in a short note" as being body-centered cubic (CsCl type), but no parameters are given. The analogy between the three systems, which is perfect as far as the two phases of the type Ti2X and TiX are concerned, disappears at the titanium-poor end of the diagrams. In the system titanium- iron, TiFe2 has an hexagonal (MgZn2 type) struc-ture with the parameters given in table I. The existence of TiFe3 has also been reported8 (table I) but was questioned by other investigators2 and is also refuted by the present study. In the system titanium-cobalt, a phase corre-sponding to the composition TiCo2 has been investi-gated by Wallbaum and Witte6 who claim that the structure is cubic (MgCu2 type) for alloys slightly deficient in cobalt and hexagonal (MgNi2 type) for alloys slightly deficient in titanium. The parameters of the two phases are given in table I. In the system titanium-nickel, the nickel-rich phase corresponds to the composition TiNi3 and has been described as hexagonal7 with the parameters given in table I. The present investigation was initiated for the purpose of filling in the gaps in the knowledge con-cerning the structure of the various phases sum-marized in table I. Since the titanium used by Wallbaum and his collaborators was only 95 pct pure,' it was found desirable to redetermine the lattice parameters of the alloys prepared with a

Jan 1, 1951

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968

[Aalde, Kaare, ('40) New Mexico School of Mines, Socorro, N. M. Abadesco, Enrique A., ('39) Univ. of the Philippines, Manila, P. I. Abdul-Ahad, A., ('39) Montana School of Mines, Residence Hall, Butte, Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acker, Voscoe, . ('39) Agricultural & Mech. College of Texas, College Station, Tex. Acosta S., Gonzalo, ('40) Univ. of Texas, Univ. Sta., Box 1785, Austin, Tex. Adams, Albert, ('38) New Mexico School of Mines, Socorro, N. M. Adams, Charles W.,' ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams, Hugh T., Jr., ('39) Univ. of Oklahoma, Norman, Okla. Adams, Jack L., ('39) Univ. of Oklahoma, Norman Okla.]

Jan 1, 1940

By Douglas R. Piteau

Douglas R. Piteau (Engineering Geologist, De Beers Corp., Kimberley, South Africa; Presently Consulting Specialist at Nchanga Mine Open Pit, Chingola, Zambia)-Mr. Lutton is to be commeneded on his analyses and presentation of such practical data which can be used for predicting a preliminary optimum slope angle in rock. It appears that he assumes all slopes analyzed to be straight. Although there are overriding factors which affect the general slope configuration, such as structural discontinuities, ground water, and other environmental factors such as weathering conditions, regional stress, etc.,8 the affects of plan geometry under certain conditions also can be of outstanding importance. In investigation of natural slopes, for example, the effects of plan geometry are not entirely appreciated and it is in this respect that discussion is given. Experience in southern Africa has shown that the overall geometry of surface openings in rock, particularly those with dimensions of the order of 1500 ft or less, i.e., where radii of curvature of the slopes are less than, say, 700± ft, must be considered in rational slope-stability analyses. That is, the slope angle is not only a function of slope height, strength of the mass, and geometry of structural discontinuities, but also is dependent upon the plan geometry of the local slopes and the plan shape of opening. Technically speaking, adequate analysis of the slope must be three-dimensional, the third dimension being that of overall plan configuration and the analysis must incorporate its subsequent effects. However, current theories of slope stability all deal with the slope as a two-dimensional problem, i.e., a slice of unit length of an infinitely long slope is considered for a condition of plane strain. In this the tacit assumption is made that the plan radii of the crest and toe of the slope are infinite and no attention is given to the plan geometry of the slope. Clearly this is not the condition encountered in practice, particularly in open pit mining where excavations, relatively speaking, can be small and where these radii of curvature accordingly can have important affects on the slope stability. This is illustrated by the analyses of Piteau and Jennings 9 of the natural slopes which had developed around pipes of four diamond mines in the semiarid Kimberley area of South Africa. Although these slopes consist of dolerite overlying shale, the values of the slope angles of all the pits were corrected for a height of slope of 320 ft assuming that no dolerite occurred. This brought the data onto a comparable basis. These data were analyzed statistically and a clear empirical relationship, as is shown [in Fig. 4], is seen to have formed between angle of slope and curvature of slope, i.e., the angles of slope are greatest where the radii of curvature are least. Also, it can be seen that the slope of each line is different, indicating that the plan shape of the open pits also are significant, the curve being steepest for the open pits which are more circular in shape in contrast to those which are more elongated. The effect of slope curvature on the average angle of slope for the two extreme radii of 200 ft and 1000 ft for all four open pits is 39.5° and 27.3°, respectively. Hence, the concave curvature effect represents an average increase in slope angle of 12.2° from the essentially straight slope. In quantitative terms in Mr. Lutton's Fig. 2, this represents displacing the curve for a 320-ft pit from the second curve from the bottom (i.e., shale in subtropical climate) to that of the third from the bottom (i.e., quartzite in temperate environment).

Jan 1, 1972

E. T. Turkdogan (British Iron & Steel Research Assoc., London, England)—I would like to suggest a different method for the treatment of the authors' data on the Si-0 equilibrium in liquid iron. Because the activity coefficient of silicon dissolved in iron is influenced by the concentration of silicon as well as that of oxygen, the equilibrium constant K2 of reaction 2 becomes a function of metal composition, and, as shown in Fig. 1, a plot of log KP1 at 1600°C against the weight percent of silicon gives a smooth curve. A similar curve is obtained when log Kzl is plotted against the oxygen content of iron. Before

Jan 1, 1955

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By T. J. Bosworth

The effect of hydrogen pretreatment of alumina, magnesia, and zirconia crucibles on reduced oxygen levels in iron charges has been studied. Hydrogen treatment of commercial high-purity magnesia crucibles was observed to produce as high as 70 pct reduction in oxygen content in iron melts. Hydrogen treatment of the commercial high-purity grade zirconia crucibles produced a 25 pct reduction in oxygen levels in iron melts. An average reduction of Knoop hardness of 47 pct was recorded on the iron charges melted in hydrogen-treated crucibles. On the basis of the experiments and the free-energy diagram, it appears that the major source of reducible oxygen to the iron charge is the suboxides and impurity oxides rather than the major oxide of the crucible. Suitable pretreatment of the crucibles to reduce and remove these oxides yields low oxygen levels in iron melted in the crucibles. DURING the last decade, attempts to produce more pure and uniform alloyed metals have brought about the development of many new melting techniques. Notable among these are vacuum-induction melting, inert and consumable-electrode melting, the cold-mold technique, and numerous techniques for removal of impurities by chemical reaction. However great the achievements in this field, metals must still be melted in contact with media of varying reactivity; i.e., gas, ceramic, and slag. Studies have been made to attain an understanding of the reactions that take place during melting, including slag-metal reactions and equilibria, equilibrium of hydrogen and water vapor, and carbon dioxide and carbon monoxide with oxygen in molten iron. These reactions have been treated quite thoroughly. There is one condition, however, that has been widely overlooked, and, to the author's knowledge, only cursive investigation has been made of it. This is the reaction between the ceramic crucible material and the iron charge. In recent years, Hadley and Bianchi' made a series of studies on hydrogen deoxidation of iron in magnesia crucibles. Bianchi2 studied crucible-FeO equilibria in the temperature range 1525°to 1650°C in high vacuum with, however, inconsistent results. Richardson and Jeffes3 in their series of articles on thermodynamic reactions in the making of iron and steel refer to Wentrup and Hieber's4 work on iron and aluminum deoxidation. Their pork included melting iron in alumina crucibles and measuring the aluminum and oxygen content in the iron. Because of the low values obtained, question has arisen of their analytical accuracy.3 Dastur and chipman5 obtained values on hydrogen-oxygen equilibrium in molten iron contained in alumina crucibles similar to those obtained in experiments in the present program. Hochmann6 studied removal of impurities in chromium irons in high vacuum. His results with respect to oxygen level in chromium-iron melted in magnesia crucibles are consistent with results we have obtained.

Jan 1, 1959

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to froth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkins1 reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon- hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group.

Jan 1, 1954

By Richard E. Chism

I have thought it well to lay before the Institute some account of the Vallecillo Mines, now, I believe, the only paying ones in American hands in northeastern Mexico, including the States of Nuevo Leon, Coahuila and Tamaulipas. The authentic history of these mines dates from their ownership by an American Company in the year 1851, when they were bought by the Vallecillo Silver Mining Company of New York. They had been worked before by the Spaniards, but had been abandoned for many years, on account of the heavy expense of drainage and the constant incursions of the Indians. The company commenced work with several well-known New York capitalists among its stockholders, and had a large fund of both money and enthusiasm. The first point of attack was at a shaft on a mine known as the Jesus Maria, which had the most favorable traditions. Extensive buildings were put up, and two sets of pumps were successively tried. After the second pump, with a steam-cylinder 5 feet in diameter and 10 feet stroke and a plunger 20 inches in diameter, had failed to do more than hold the water, with infinite labor, at the 250 feet level, and after a thorough exploitation of the whole mine above that level had failed to yield more than some $30,000 worth of ore, it was resolved to abandon the effort. Operations were accordingly transferred to the old Dolores shaft, at a point about 21/2 miles to the

Jan 1, 1885

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By AIME AIME

R. A. Hadfield, W. H. Bleckly, The Rt. Hon. Sir James Kitson, Bart., M. P.&apos;, E. Windsor Richards, E. P. Martin, Andrew Carnegie, Sir Hugh Bell, Bart., Bennett H. Brough. Patrons. Adamson, Joseph, & Co., Hyde; Aird, John, & Co., London ; .Akrill, C., & Co., Ltd., West Bromwich ; Anderson Foundry Co., Ltd.,. Port Clarence, Middlesbrough ;. Armstrong, Sir W. G., Whitworth & Co., Ltd., Newcastle-on Tyne ; As¬sociated Portland Cement Manufacturers (1900), Ltd., London; Babcock & Wilcox, Ltd., London; Baird, William, & Co., Ltd., Glasgow ; Baldwin&apos;s, Ltd., Stourport; Barclay, Andrew, Sons & Co., Ltd., Kilmarnock; Barrow Hematite Steel Co., Ltd., Barrow-in-Furness; Bayliss, Jones & Bayliss, Ltd., Wolverhampton ; Beardshaw, J., & Son, Ltd., Sheffield ; Bell Brothers, Ltd., Middlesbrough ; Bolckow, Vaughan & Co., Ltd., Middlesbrough ; Booth, Joseph, & Bros., Ltd., Leeds ; Briton Ferry Works, Ltd., Briton Ferry; Butlin, Thomas, & Co., Ltd., Wellingborough ; Butterley Co., Ltd., Alfreton ; Byrne, James, & Co., Middlesbrough; Cargo Fleet Iron Co., Ltd., Middlesbrough.;. Carnforth Hematite Iron Co., Ltd., Carnforth ; Cochrane & Co., Ltd., Middlesbrough ; Coltness Iron Co., Ltd., Glasgow ; Colville, David, & Sons, Ltd., Motherwell ; Consett Iron Co., Ltd., Consett ; Cooke, William, & Co., Ltd., Tinsley ; Craggs, R., & Sons, Ltd., Middlesbrough ; Darwen & Mostyn Iron Co., Ltd., Mostyn ; Dorman, Long & Co., Middlesbrough ; Dunlop, J., & Co., Ltd., Glasgow ; Ebbw Vale Steel, Iron & Coal Co., Ltd., Ebbw Vale ; Engineer, The, The Proprietors. of, Lon¬don ; Engineering, The Proprietors of, London ; Etna Iron & Steel Co., Mother¬well ; Farnley Iron Co., Ltd., Leeds ; Firth, Thomas, & Sons, Ltd., Sheffield ; Rather, W. T., Ltd., Sheffield ; Fraser & Chalmers, Ltd., Erith ; Frodingham Iron & Steel Co., Ltd., Doncaster; Gjers, Mills & Co., Ltd., Middlesbrough ; Glenboig Union Fire-Clay Co., Ltd., Glasgow ; Glengarnock Iron & Steel Co.; Ltd., Glengarnock ; Guest, Keen & Nettlefolds, Ltd., Birmingham ; Hadfield&apos;s Steel Foundry Co., Ltd., Sheffield ; Hall, J. & E., Ltd., Dartford ; Harkness, W.; & Sons; Ltd., Middlesbrough ; Harrison & Co., Ltd., Lincoln ; Head, Wrightson & Co., Ltd., Stockton-on-Tees ; Hill, John, & Co., Middlesbrough ; Hingley, N., & Sons, Ltd., Dudley ; Hopper, John I., Ltd., Thornaby-on-Tees; Hull Forge Iron &-Steel Co., Ltd., Hull; Iron and Coal Trades Review, The Proprietors of, London ; Ironmonger, The, The Proprietors of, London ; Jackman, Joseph, & Co., Ltd., Sheffield ; Jessop & Appleby Bros., Ltd., Leicester and London ; Jes-

Nov 1, 1906

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation&apos;s Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

By D. C. Ganow, N. J. Grant, I. R. Silver, A. R. Chaudhuri

The structural changes that result when a metal is "cold worked" lead to higher values of yield and tensile strength on subsequent deformation at room temperature. Further it has been shown that the beneficial effects of cold work are, to some extent, maintained even at elevated temperatures. The strength improvements from prior cold work decrease as the temperature is raised and are a function of grain size, amount of cold work, and strain rate (or time of test). If recrystallization occurs during test, the cold-worked material may even show weaker stress-rupture properties than the annealed material. A question that arises is whether there is a significant effect on the subsequent creep behavior if the prior deformation is performed under creep conditions at high temperatures not too different than the test temperature, but at significantly different strain rates and for various amounts of strain. An answer to this question was sought in the work described in the present paper. PROCEDURE Two materials were used in this work, high-purity aluminum and a solid-solution A1 2 pct Mg alloy. The compositions are shown in Table I. The grain size in the two materials was 0.2 to 0.3 mm. The deformation for both the prestraining and for the creep tests was at constant stress. The procedure adopted was to prestrain a specimen to the desired elongation, remove the load, and cool to room temperature rapidly by spraying. the test bar with cold water. The specimen was then placed in a creep machine, held at the test temperature for less than 5 min, and loaded. Less than 15 min was required to bring the specimen to temperature. The creep stress was based on the diameter resulting from the prior strain, and values of elongation at fracture listed in the tables do not include the respective elongations resulting from the prestrain. The choice of the stresses for the prestrain and for the creep tests was made so that the tests could be completed in relatively short times to maximize any effect of prestrain. The specimens had a gage length of 1 in., the pure aluminum specimens having a diameter of 0.150 in. and the alloy specimens a diameter of 0.125 in. For pure aluminum, prestrain was at 400&apos; and 600°F with testing at 500°F; for the alloy, prestraining was at 700°F and testing at 600°F. RESULTS The prestrain conditions for the aluminum and the alloy specimens are shown in Tables I1 and IV. In addition to showing the time required to achieve the desired prestrain, the expected rupture Lives are given which would have resulted had the creep prestrain been continued to fracture. The prestrained and the annealed specimens were then tested in creep to fracture; the temperature and stress for the pure aliminum specimens being 500o F and 1800 psi and for the alloy, 600&apos; F and 3400 psi. The creep curves for the prestrained and the annealed specimens of pure aluminum showed all three stages of creep; hence in addition to the effect of prestraining on the rupture life, it was also possible to determine the effect of prestraining on the minimum creep rate, and on the time and elongation at the end of each of the three creep stages. The results are shown in Fig. 1 and Table 111.

Jan 1, 1960

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation&apos;s mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942