Search Documents

By John D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space.

Jan 9, 1959

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-In this exposition of experimental data, the author infers, indirectly at least, that by the Charpy test information was obtained that led to the improve-ment of certain ordnance parts and that this improvement could not have been attained without the Charpy test. On examination of the data, however, it appears that the important point of the whole matter was that while the material had been accepted from the results of longitudinal tensile tests, it was really transverse ductility that was desired. The writer has no desire to attempt to detract from the value of the paper or to discredit the Charpy test in any way, but he would like to ask the author if he will not give more clearly his reasons for preferring the Charpy impact test for investigational and control work of this kind, over the more usual tensile test made in a transverse direction. The tensile test pieces are more cheaply made than the square notched impact bars; and from the former the limit of elasticity and the ultimate strength as well as, the ductility are obtained, while in the Charpy test only one property is measured. It does not seem that the author has shown a sufficient reason for favoring the latter test, when both it and the trans-verse tensile test served his purpose equally well in indicating the proper metal and treatment required for his special forging, and it is hoped that this reason will be given more clearly as a matter of useful general information.

Jan 11, 1919

By S. L. Crouch, C. Fairhurst

The general term "coal mine bump" refers to the sudden and violent failure of in-situ coal. Coal bumps occur in most countries where coal is worked by underground methods. They are related to geological factors and mining techniques. Coal bumps can be characterized as unstable releases of energy associated with yielding that occurs with progressive mining. Unstable releases of energy occur when the coal is able to absorb less energy than is released by the surrounding rock mass during the yielding process. At any stage of mining, the amount of excess energy so released is governed by the mining geometry, the overburden stress, the elastic properties of the rock mass, and the stress-strain characteristics of the seam material. If the coal in the vicinity of the working face is crushed, the peak abutment pressure occurs at some distance into the intact portions of the seam, and mining takes place in essentially destressed coal. With subsequent mining, additional yielding occurs, excess energy may be released, and the peak stress is again shifted into the solid. This process continues until the mining geometry is such that the zone of peak stress is effectively surrounded by yielding coal, at which point it can be anticipated that further mining will produce dramatic redistributions of stress and be accom¬panied by large releases of energy. On this basis, the differences between several alternatives for mining a given block of coal may be pronounced.

Jan 1, 1975

By Arthur Foote

AT THE end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping Southwest, or, exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North. Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a North-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly.

Jan 1, 1930

By John A. Church

The Lake Superior blast-furnaces probably represent the maximum economy of fuel possible in this country. They smelt an ore which is very rich and easily reducible, and as the small amount of gangue present is not all silica, but in part a silicate, the amount of limestone required is a minimum. The average yield of the ore treated at six furnaces was 63 per cent., and the average quantity of limestone 179 pounds per ton of pig. The fuel used is charcoal, so burned as to retain most of the combustible volatile part, which, before the utilization of furnace-gas, was burned away. With these conditions it is not surprising that the Lake Superior charcoal practice is extraordinary in almost every respect. In any scientific discussion of American furnace work, the establishments there will be found at the head of the list, and they work under conditions which are extremely favorable for careful study. The Bay Furnace, near Marquette, has the honor of carrying "the broom" for the largest daily make. With a capacity of 1908 cubic feet it has, for months together, produced 29 tons of pig, graded at

By A. N. Roberts, N. W. Stump

New developments in on-stream analysis using immersed radioisotope gages including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding, which is based on maximum throughput at constant product size, and preliminary work in flotation control are also outlined.

Jan 1, 1975

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. K. Welch, C. W. MacGregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By M. P. Tixier, K. S. Kunz

A method for the interpretation of temperature curves recorded in gas producing wells is described. One essen-tial feature of the method is a simple graphical construction which conveniently reflects the amount of gas flowing from a given producing formation. This method, applied in conjunction with the Induction Log and radioactivity logs, is valuable to determine the points of entry of gas and to estimate the over-all thickness of the producing zones and their respective contributions to the total production. The method in particular is helpful in evaluating the effect of fracturing operations. An outstanding result of the application of the method is to bring to the light the relative importance of sand-shale interfaces in the production of gas. The paper is illustrated with field examp1es. INTRODUCTION The electrical logging tools involving conventional systems are not applied in wells which do not contain water base mud (empty holes, or wells filled with oil base mud), because of the absence of electrical connection between the electrodes and the surrounding formations. It is, therefore, common practice in this case to use other methods which do not require the presence of a conductive fluid in the borehole: resistivity log with scratcher electrodes, Induction Log, radioactivity logs, temperature log. . . . Such conditions are encountered in some regions, as the San Juan Basin, N. Mex., where a technique of drilling gas wells, using gas as a drilling fluid, has been introduced in the last two years. By the middle of 1953, an appropriate method for the logging of these wells was devised on the basis of field tests and of theoretical studies. It is the purpose of the present paper to give a description of this method. In these wells the logging operations are performed during the process of gas production, so that the temperatures in the boreholes are strongly affected by the cooling due to the expansion of the gas. On the other hand, a special thermometer, with a high sensivity and a short time constant, has been recently made available, which has enabled much more detailed and accurate recordings of the borehole temperatures than with the conventional instruments. As a result of these two circumstances, the temperature log constitutes the essential element of the method, in making possible the detection of the gas producing zones, the definition of their boundaries, and the estimation of the respective contributions of each separate zone to the total production. The method also involves the radioactivity and Induction Logs, as auxiliary documents. These logs in the present instance are helpful in the determination of the reservoirs. However, the information they give in this respect is limited. This comes from the fact that, due to the absence of the MicroLog and/or MicroLaterolog and of the SP log, the estimation of formation factors and connate water salinities is somewhat conjectural. Furthermore, little help is obtained from the Neutron log for the evaluation of porosity and of formation factor because the variations of gas saturation affect the Neutron log in a way similar to the variations of porosity. It should be said also that even an exact knowledge of the gas saturation of the reservoir beds would not

Jan 1, 1956

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 11, 1918

By Dr. O’Neil Thomas J., Donald W. Gentry

It was a western truism that more money was made from selling mines than from buying them, just as it was accepted that many a good mine had been spoiled by working it. from R. E. White, "The Mining Town," Alta California August 18,1873 INTRODUCTION One of the most important aspects of mineral enterprises of US corporations is the influence of the depletion allowance on cash flow. This allowance permits mineral producers to claim sizable federal income tax deductions not available to other industries, and these deductions significantly increase cash flows in mining. In the past several years the minerals depletion allowance has come under increasingly heavy fire from many sectors as a tax loophole that deprives the federal government of large amounts of revenue. One estimate of the loss of tax dollars in 1968 was $2.25 billion due to depletion deductions and intangible expenses in the oil industry. Largely on the basis of such arguments, the Tax Reform Act of 1969 reduced percentage depletion rates for a number of minerals, and the Tax Reduction Act of 1975 totally eliminated statutory depletion for most oil and gas. In regard to percentage depletion for hard minerals, the federal government has estimated its resulting loss of revenue at $1.75 billion for 1980. The TEFRA legislation of 1982 further reduced the statutory depletion allowance available to iron ore, coal, and lignite beginning in 1984. Thus, it is clear that minerals engineers and managers should have a thorough knowledge of the origin, evolution, justification, and computational procedures relating to the depletion allowance. ORIGIN AND EVOLUTION OF THE DEPLETION ALLOWANCE

Jan 1, 1984

By R. C. Palmer

THE testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and iii oils has made such work necessary as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being wasted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 8, 1916

Executive SIDNEY J. JENNINGS, Chairman. GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 6, 1918

By J. G. McCullough

The paper is a general description of the U.S. lead and zinc industries as they are now compared to ten years ago and the effect of recent world-wide developments. Topics of interest concerning lead are the present and potential growth of the lead-acid battery business, the potential hazards of having one outlet for a major proportion of production, the expanding U.S. secondary lead production, the hardships of stringent hygiene and environmental regulations and the future supply and demand outlook. The present poor condition of the U.S. zinc industry caused by an oversupply of zinc metal - mostly in Europe - is discussed and also the shifting markets influenced by the automotive programs to reduce the weight of cars and the continuing high mine production due to the mixture of metals contained in the massive sulphide deposits which contain a major portion of the zinc metal reserves. This is all tempered by technical advances in die casting and the emphasis on the protecting of steel with zinc to prolong its useful life. New U.S. mine and smelter production facilities will be restrained due to lower cost foreign zinc from better grade ore deposits and the insistence by Governments for refining capacity to be constructed in the country that the ore is mined.

Jan 1, 1977

Jan 1, 1946

Jan 1, 1951

By Lawrence Adler

The authors are to be complimented on using a novel and potentially helpful technique to analyze the effects of mine roof trusses. However, some criticisms of their application and analysis seem appropriate to further its acceptance. This discussion will deal with the normal structural analysis format covering: 1) material, 2) load, 3) structure, and 4) analysis. It will then briefly review the testing procedures and finally cover miscellaneous items.

Jan 12, 1978

By William H. Emmons

The problem of the metalliferous veins has always been an outstanding one in the science of ore deposits. In recent years interest has been stimulated by Spurr, who maintains that veins have consolidated from magmas that have densities as great as the densities of ordinary rocks. Lindgren published a noteworthy paper1 in 1926, in which he supports the theory that veins are deposited chiefly by hot waters. Lindgren's paper was discussed by Singewald, Spurr, Kemp, Anderson, Colony, Bateman, Porter and others. The discussion, in the main, was centered on the interpretation of fragments that are included in veins. This paper also treats the problems of fragments in veins and includes a reply to a review by Spurr2 of a bulletin by Larsen and myself3 published by the United States Geological Survey on the geology and ore deposits of Creede, Colorado. Mineral veins containing fragments of the wall rock are common. At many places the fragments are completely isolated, one from the other, and are entirely surrounded by vein matter. It has been stated that the vein matter around the fragments was heavier than the fragments and that the latter were floated in a magma. J. E. Spurr, who is the leading advocate of this hypothesis, 4 urges that normal mineral veins were deposited by solutions heavy enough to float fragments of the country rock, and it is mainly on this relation that he bases his theory that veins are deposited by solidification of magmas. If it can be shown that vein-forming solutions have a specific gravity greater than rock (2.77), one is justified in regarding them as true mag-matic solutions. It is shown later in this paper, however, that at Lead, S. D., water not more highly concentrated than ordinary drinking water is depositing vein matter around fragments of schist and of steel in such a manner that the fragments are completely isolated and completely surrounded by the mineral cement.

Jan 1, 1928

By C. W. Crispell

The four nomograms presented in this article were designed to simplify and make more rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic sca1e. † For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Power foR CompREssion It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Fig. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: S X 144 PVn [(P')n-1/sn -1 (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, -in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 1, 1918

By E. Miller, N. Chou, K. Komarek

The solid solubilities of the compounds PbS, PbSe, and PbTe have been determined by equilibrating single crystals with two phase alloys. The solubilities were determined by measuring the Hall coefficient of the equilibrated samples. The observed maximum deviations from stoichiometry on the lead rich and the chalcogen-rich side of the phase fields were: at. pct excess Pb at pct excess S at 850°C; PbSe--4 x 10'" at. pct excess Pb at at. pct excess at 800°C; and PbTe-2.8 x 10 4 at. pct excess Pb at 780°C, 10"1 at. pct excess Te at 720°C. The previously developed theory of retrograde solubility has been expanded to include intrinsic disorder in the compounds, and the experimental results are in agreement with the theory. THE solid solubility limits of intermetallic semiconducting compounds are of considerable interest, since many of these compounds have potential use as thermoelements in thermoelectric devices, as infrared detectors, or in semiconductor devices. The solidus curves of a significant number of these compounds have been reported to be retrograde with the maximum solid solubility occurring between the eu-tectic and the maximum melting temperatures. In a previous paper,' equations were derived which permit calculation of the maximum solid solubility of an AB compound exhibiting retrograde solubility. Derivation of these equations was based on the assumption that the compound is a nondegenerate semiconductor at the temperature under consideration, that the defects were unassociated, and that the vibrational contribution to the entropy of the compound could be evaluated by the Einstein approximation. It was shown that at the temperature of the maximum solid solubility The entropy term ASS is composed of the entropy of formation of the solid stoichiometric compound (AS$)*, and the entropy due to deviations from stoichiometric composition which is the sum of a con-figurational term (aS*), a vibrational term (AS,), and an electronic term (AS,). In the previous paper the positional entropy was evaluated considering the con- N. CHOU, Member AIME, formerly Graduate Student, New York University, N. Y., is with IBM, Yorktown Heights, N. Y. K. L. KOMAREK, Member AIME, formerly with New York University, is Professor, Department of Inorganic Chemistry, University of Vienna, Vienna, Austria. E. MI LLER, Member AIME, formerly with New York University, is Associate Professor of Mechanical Engineering, California State College at Long Beach, Calif. The paper is based on a thesis submitted by N. CHOU to the Graduate Division, School of Engineering and Science, New York University, in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Materials Science. tributions from defects arising from deviations from stoichiometric composition. The derivation is generalized in the appendix to include intrinsic disorder. The electronic entropy term is also recalculated in the appendix. Of the various semiconducting compounds, the solidus curves of Pbs,' and ~b~e,~ have been most extensively studied. The solidus of PbSe has also been determined, but the temperature of maximum solubility has not been accurately established.5129 The present investigation was undertaken to compare the experimental solid solubility data for these systems with the values predicted theoretically. Since the temperature and composition of the maximum solubility of PbSe has not been accurately determined, experimental emphasis was placed on determining the solidus curves for PbSe in the region of maximum solubility, although experiments were also performed on PbS and PbTe at several temperatures. X-ray diffraction studies were also made on carefully prepared powder samples of PbSe to determine the variation of lattice parameter with composition. EXPERIMENTAL PROCEDURE The procedure of Brebrick and Allgaier was employed for determining the solidus data. Monocrystal-

Jan 1, 1970