Search Documents

By L. G. Evans, W. W. Simpson, W. A. McKinney

In conventional dump leaching of strip wastes from open-pit porphyry mining operations, many years are required to extract a fraction of the copper from the contained sulfide minerals. Furthermore, none of the molybdenum, gold, or silver is recovered by current leaching practices. Because the copper sulfide minerals and molybdenite generally are distributed in the minute fractures throughout the host rock, the mineral values tend to concentrate in the finer fraction of the strip material. This suggests the possibility of segregating the enriched fines in as-produced or coarsely crushed strip wastes for blending with the ore grade flotation mill feed. In the past, extra handling or crushing of mine wastes to enable better leach extraction has been deemed uneconomical. However, recent articles on mobile crushing plants and conveyor haulage systems indicate possible cost improvements for these techniques over conventional truck haulage of ore and mine wastes. Another potential benefit from removal of the fines from copper-bearing mine waste derives from the increased permeability of the coarse dump material to leach solutions and air. Better permeability should result in faster oxidation of the sulfide minerals, less channeling of leach solutions, and fewer perched solution tables caused by compacted fines. Therefore, in addition to the metal values recovered by flotation, higher copper recoveries by leaching also might be achieved. The Salt Lake City Metallurgy Research Center of the U.S. Bureau of Mines undertook an investigation to determine the feasibility of removing enriched fines from strip waste material for separate treatment by froth flotation for early recovery of part of the copper, molybdenum, gold, and silver. Percolation leaching tests were made on mine-run and sized fractions of the dump material to determine the effect of fines removal on copper extraction. Samples Tested Three 10-ton samples of copper sulfide-bearing mine waste were obtained for the investigation. Partial chemical analyses of the samples are given in [Table 1] and the consolidated results of detailed screen analyses made on the samples are given in [Table 2]. The -1/4-in, fine fractions contain from 16 to 32% of the copper and 19 to 40% of the molybdenum in 11 to 18% of the total waste. The samples also were crushed to -3 in. to determine the feasibility of crushing to obtain a higher distribution of the metal values in an enriched fine fraction while providing a more leachable coarse fraction that could be transported by a conveyor system to a dump. The -%-in. fine fractions screened from the crushed mine waste were almost identical in grade to the natural fines. From 2 to 4% more1/4-in. fines were produced by crushing to -3 in. Copper distribution was increased by about 3% over that in the natural fines, while molybdenum distribution was increased by about 10%. The -1/4-in. fines screened from the mine-run and crushed strip waste were almost as high in grade as the ore being treated at the mills. In addition, the fines

Jan 1, 1974

By W. J. Keep

We have found that our graphic representations were, in some cases, not perfectly understood. In the tables by which we illustrate all our tests, the records appearing in the vertical columns between the rulings are the results of the tests of iron having the percentages and characteristics noted at the top of the column. The record is made by a short horizontal line in such vertical columns. It is located in horizontal spaces, which divide the table into units of measure, to indicate the value of the record. For example, in the upper part of Table VII. is recorded the transverse strength of the series of tests with white iron and aluminum, which were reported in our former paper. The numbers at the extreme top are the test-numbers. The fractional numbers below are the percentages

Jan 1, 1890

Jan 1, 1926

By H. E. Cline

Solidification of Pb-Sn alloys ranging in composition from 1.2 to 56 at. pct Pb ws observed with polarized light. Lamellar structures were observed over a larger range of compositions in alloys containing excess tin than excess lead, as expected from constitutional supercooling. The occurrence of pools of supercooled liquid surrounded by lead is explained by the difficulty in nucleating tin. Cells and dendrites weve observed in tin-rich alloys. Evidence was found that the degenerate structure formed at low growth rates, the formation of faults, and abrupt changes in composition and structure can be attributed to non-steady-state growth. The apparent interface shape was observed to have deep grooves at the interphase boundaries. HUNT and Jackson have observed the shape of the interface during growth of organic eutectics. They observed the formation of lamellar faults and shape instabilities upon changes in growth rate. The lamellar structure in these organic eutectics was not restricted to the eutectic composition. Recent work by Mollard and Flemings2 indicated that Pb-Sn alloys from 12 to 26 at. pct Pb could be solidified with a lamellar or rodlike structure if a sufficiently steep temperature gradient was used at a slow growth rate. Observations of the solid liquid interface of the Pb-Sn eutectic were made by Davies3 using polarized light. Photographs were at too low a magnification to determine the interface shape, but he has concluded that tin was the leading phase. In the following experiments, solidification of a range of Pb-Sn alloys from 1.2 to 56 at. pct Pb was observed using polarized light, to determine the factors controlling stability of the lamellar structure. EXPERIMENTAL Procedure. One hundred-gram ingots of alloys prepared from 99.999 pct pure Pb and Sn were cast into graphite molds under argon. The compositions of the alloys were 1.2, 6, 12, 26, 36, 46, and 56 at. pct Pb. Two-gram pieces were melted between two cover glass slides which were squeezed into a 1-mm separation. Samples were then observed under polarized light in a hot stage shown in Fig. 1. A long working distance objective designed for viewing at 500 times was used. Photography was made difficult by the lack of illumination and contrast at these high magnifications. By using an elliptical polarization compensator, as suggested by A. Holik, the contrast and illumination could be optimized. Photographs could be taken only at slow growth rates to avoid excessive interface motion during the 15-sec exposure used. The solidification rate was varied by increasing or decreasing the power to the heater. It was found that insulation was necessary to avoid undesired growth rate fluctuations. The temperature gradient, as measured with two thermocouples 1 cm apart, was 80" ± 20°C per cm during all the experiments reported here. The advantage of this procedure is in being able to observe solidification while it is occurring. However, the observations are restricted to the glass-metal surface and may be influenced by this surface. Also, one has no knowledge of the interior of the sample, in contrast to studies of the freezing of transparent organic eutectics.' Observations. The alloy near the eutectic composition (26 at. pct Pb) solidified in a lamellar structure when the growth rate was uniform. If the growth

Jan 1, 1968

By H. W. Seamon

THE data here given were obtained by 1500 tests made, by the United Verde Copper Co. to determine the most economical air pressure for the operation of hammer drills under the varying conditions of use, and to investigate the variation in drilling speed at different air pressures Twelve models of drills were used at gage pressures ranging from 40 to 130 lb. No effort was made to harmonize theory and practice; but rather to formulate empiric rules that would cover the. average variation of the results obtained. These rules on the performance of hammer drills, based on the air pressure as the main variable, however, are not necessarily of universal application, but they apparently satisfy the results obtained in this series of tests. The drilling conditions at this property vary widely; an average of twenty-one machine shifts to a 3-ft. (0.9-m.) round has been found necessary in some of the development work, while an, advance of 56. ft. has been made in seven shifts in the "oxide" ground. This range pre-eludes the adoption of one type of drill as a standard; consequently almost every kind of hammer drill sold in this country has been tested. At present, sixteen models are in use, of which two types of the heavy (150 to 160 lb.) mounted drills, one of the light mounted drill, one stoper, and two hand plugging drills are considered as standard.

Jan 1, 1921

By J. Moore Samuel

THE prospective change in ore receipts at the Copper Queen reduction works necessitated a careful study of conditions to determine the most economical method of smelting. The first step, calculating the known, probable, and possible results, showed the economy of a unimetallurgical flow sheet f which the three pyrometallurgical stages would be roasting, reverberatory smelting, and converting. The past and future ore receipts (not including converter flux) are as follows: AVERAGE MONTHLY FUTURE MONTHLY RECEIPTS, 1918 RECEIPTS TONS PER PER CENT. OF TONS PER PER CENT. OF MONTH TOTAL RECEIPTS MONTH TOTAL RECEIPTS Ore 84,553 82.3 43,000 44.0 Gravity concentrates 16,375 15.9 25,500 26.0 Flotation concentrates 1,883 1.8 29,400 30.0 Total 102,811 100.0 97,900 100.0 Of the 102,811 tons per month received in 1918, only 28,945, or 28 per cent., was treated in the roasters and an average f 14.1 roasters out of 20 were in operation; the remaining ore was treated in the blast furnaces. The change to "all reverb." practice, therefore, called for considerable additional roaster capacity, which could be obtained either by building additional units, or by remodelling the present units so as to give increased unit capacity. In view of the progress in roasting practice since the construction of the Copper Queen roaster plant and the heavy investment in that roaster plant, the second plan seemed to be the more desirable. The Copper Queen roaster plant consisted of twenty six-hearth, McDougall roasters, 18 ft. in diameter, equipped with cast-iron arms that originally were water cooled but now are air cooled. They have no top dry hearth and the feed is discharged through the top arch, near its periphery, by plunger feeders from two bins at opposite sides of the roaster.

Jan 7, 1921

By E. W. Edson, F. W. Hertal

In some fields the problem of mud fluid is simple and easy of solution. But in the Ventura Avenue field the acquisition and disposal of good drilling mud is not the least of the problems that confront the operator. In fact, mud fluid in the Ventura Avenue field is a very important factor in the drilling of the wells. It is quite probable that many of the factors affecting mud in this field will not be found in most of the fields with which the reader is familiar. However, in the fields where the mud fluid causes no apparent problem it is probable that some of the points brought out in this paper could be used to economic advantage. In fields where caving and squeezing formations and high gas pressures are present, as in the Ventura Avenue field, it is believed that application of methods outlined will be of great assistance in drilling wells. On account of the sandy nature of the formation and the lack of suitable shale bodies in the strata drilled through in the Ventura Avenue field, the wells make practically no mud during drilling. It is necessary therefore to supply drilling mud to the wells that will carry the drill cuttings to the surface, and also will " wall up" the drill hole and prevent the sandy formations from caving. Mixing and Handling Mud Fluid The clay used to make the mud fluid is obtained from a shale stratum in the upper Pico (Plioccne) formation found about a mile on either side of the field. Since high gas pressures and caving formations were first encountered in the Ventura Avenue field and mud fluid was needed to combat them, the mixing of this mud fluid has gone through a process of evolution. First, the clay was mined and hauled to the derrick, where it was shoveled into the well and left for the churning action of the bit to mix into a mud in the hole. The next move was the construction of a mixer to mix the clay to a mud fluid which was pumped into the well. These mixing

Jan 1, 1930

By Carl H. Beal

DURING the latter part of 1915 and the first half of 1916, the writer held the position of geologist in connection with the conservation work instituted by the U. S. Bureau of Mines, on oil and gas land belonging to the Indians of the Five Civilized Tribes in Oklahoma. The duty of the geologist was to correlate formations containing oil, gas, and water, and to determine the relations of these substances in the different formations so that the conservation agents might carry on their work most intelligently. On account of the rapid development of the Cushing field, which lies in the western part of the Creek Nation, much work was done there by the inspection force. In the course of the geologic studies a large amount of information was collected, which, on analysis, has disclosed some interesting facts worthy of publication. The report, of which the following remarks are an abstract, has been prepared and submitted to the U. S. Geological Survey for publication. This report is now (June, 1917) in the press and will doubtless be issued in a few weeks. Methods Used In addition to the structure maps showing the folding of the Pawhuska limestone, which crops out in several places in the Cushing field, separate structure maps of the three most important productive sands—the Lay-ton (Fig. 2)) Wheeler, and Bartlesville—have been prepared. These structure maps were prepared by obtaining the logs of nearly all the wells

Jan 1, 1918

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

By C Gunther

Ore deposits are commonly divided into two classes, syngenetic and epigenetic, according to whether the ore was deposited together with the enclosing rock or was introduced after its deposition or solidification. Epigenetic deposits, which are by far the more important class, owe their formation to the channels that permitted the ingress of their metals, and both classes are subject to great modification by post-mineral changes in the containing rocks. A discussion of the structural features of rocks, therefore, necessarily precedes any consideration of ore deposits or processes of ore deposition. The arrangement of sediments in parallel and approximately horizontal layers is called stratification, and is an original prop¬erty of sedimentary rocks. Successive strata of the same sedimentary bed commonly differ from each other in some minor characteristic, such as texture or color, which results in a bedded or stratified appearance. The subjection of a rock to pressure develops within it parallel planes of weakness, called cleavage planes, along which the rock breaks into relatively regular slabs or blocks; the direc¬tion of these cleavage planes, which bear no relation to stratifica¬tion, is determined by the direction of the pressure that produced them. Where there are more than one set of cleavage planes, one of them is likely to be more prominent than the others. In sedimentary rocks, the cleavage may coincide with the stratifica¬tion but more commonly cuts across it. Van Hise has defined cleavage as the "capacity present in some rocks to break in some directions more easily than in others." Cleavage, therefore, does not imply the existence of subdivisions, but rather the tendency to subdivide along certain planes.

Jan 1, 1932

By Robert W. Phelps

It is gratifying to observe the growing interest in the study of oil-well spacing. It should always be held in mind that the problem of optimum spacing is to obtain the maximum return of capital per acre drained. This naturally evolves.into a mathematical consideration. As mathematics is the basis of all science, an effort should be made to develop formulas which involve data obtainable in the early stages of development. The first information from a discovery well in a new field would be the character of the sand, rate of initial production of oil and gas, viscosity of the oil, rock pressure, etc. Later, from this well, if Herold's theories of hydraulic, volumetric and capillary controls are accepted, could he determined the ultimate production as without interference from drainage by subsequent well completions, and under which control the well is producing. If it should prove to be producing under capillary control, a rough estimate could be made of it's radius of drainage. With but one well, the radius of drainage, or the interference of drainage of individual wells by close spacing, would be estimated by comparison with similar conditions in other fields in which the development has progressed sufficiently to furnish the data. A second well that is spaced sufficiently close so that an interference can he observed after its ultimate production is estimated, will furnish data to develop a desirable spacing of wells which can be inaugurated for that area and which is capable of producing a uniform amount of oil under like conditions. In some fields this area will be extensive, in others each well location will require an individual study. In 1924, Cutlerl developed a scheme whereby he determined by tabulation a spacing of oil wells for the maximum return per acre. After a study of production in a number of fields, he developed the following as a tentative rule: "The ultimate production for wells of equal size in the same pool where there is interference (shown by a difference in the, production decline curves for different spacing) seems approximately to vary directly as the square roots of the areas drained by the wells. This rule may also he stated thus: The recovery from wells of equal size

Jan 1, 1929

By R. K. Govila, E. H. Parkison

THE interplanar angles for hcp metals vary with c/a ratio, and therefore must be computed separately for each particular metal or alloy. Manual computation of these angles is laborious and time consuming, and for this reason computer programs have been developed to accomplish this task.1"3 However, these programs have certain disadvantages. For example, they require prior knowledge and understanding of ALGOL or FORTRAN languages. Further, they will not print out specific angles but instead give all angles between given limits—thus program2 prints out a total of 26,649 angles between planes with indices and in the range from (4 4 4) to (4 4 4) for any given c/a ratio. The purpose of this note is to present a simple and inexpensive computer program for accomplishing this task. This program is written in BASIC language4 which does not require any prior knowledge of computer programming, and is ideally suited for nonprofessional programmers. It also provides flexibility for the user by allowing him to select any indices for as many or few planes as desired for any given c/a ratio. The computer program proposed below is based on the relationship in which + is the angle between any two planes and . TO illustrate use of the program, consider the problem of calculating the interplanar an-

Jan 1, 1970

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By Michael Hoch

The phase diagrams of binary systems of some of the transition elements of Groups IV, V, and VI were used to compute the partial free energies of these elements and the free energy of formation of their Laves-type compounds. From these data, isothermal sections of ternary phase diagrams were calculated and compared with experimental results. DURING the investigation of ternary and quaternary high temperature systems formed by the transition elements of Groups IV, V and VI, the binary phase diagrams for these elements available in the literature were studied. In this study, the free energies of formation of the compounds formed in these binary systems were calculated; these values were then used to determine the general shape of the ternary and quaternary phase diagrams. Above 900°C, the transition elements of Groups IV, V, and VI are all bcc and form only Laves-type compounds in binary systems. The investigation was based on the binary phase diagrams published by Hansen.1 The Cr-Nb system was constructed from the data of Elyutin and Funke.' Several unpublished phase diagrams were taken from Schmidt'sLo and English'sl1 compilations. THE BINARY SYSTEMS valuations of the Thermodynamic Functions. Rostokers evaluated the boundaries of the (a + b) field in Ti-base alloys with a two-constant equation. The authors' interest is mainly in the center of the diagrams; therefore the miscibility gaps in the Zr-Nb, W-Cr, Ta-Zr, Ta-Hf, and Ti-W systems were used to evaluate the thermodynamic behavior of the binary systems. Lumsden's4 Equations 29.2, 32.1, and 33.1, page 287, were used for the excess integral free energy FeX, and for the excess partial free energies Fx and replaces b and b replacesP in Lumsden's notation):

Jan 1, 1962

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well.

Jan 12, 1951

By F. E. Turton

THE town of Rancagua, at the junction of the state and Braden Copper Co. railroads, is located 82 km south of Santiago, the capital of Chile. From Rancagua 70 km to the east, situated in the Andes at an elevation of 7000 ft, is the town of Sewell, the location of a millsite. Two and one half km east of Sewell by underground railroad at an elevation of 7500 to 10,000 ft is the Teniente orbody. The history of El Teniente dates from the eighteenth century, when according to legend a Spanish lieutenant, or teniente, a fugitive from justice, escaped to the Andes and camped at what afterwards became known as the Mineral El Teniente. This man reputedly discovered a vein of high grade copper ore. The first official records date from 1819, when some exploitation was begun, and continue until 1870. The orebody was large and of relatively low grade and was beyond the capabilities of the small groups attempting to operate it. No effort was made to erect a concentrator until William Braden became interested in the property. In 1901 Mr. Braden promoted the necessary capital for the first practical exploitation of the orebody. Barton Sewell and E. W. Nash, both of the

Jan 1, 1952

By R. G. Knickerbocker

The copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers. A short trial of the Nicholls-James process developed several facts which brought about a decision to abandon the process. Owing to the

Jan 1, 1934

By George Frederick Kunz

The garnet-district of Bohemia is situated about 60 kilometers northwest of Prague, and is bounded on the north by Meronitz and Trebnice, 12 miles apart, and by Decany and Skan on the south. This region is covered with alluvium resting on the diluvium, which

Jan 1, 1893

By L. Ormsby, H. Lines

Drilling and blasting practices in the Morenci open pit have undergone considerable modification in recent years. Changes in the character of the ground being mined, modifications of working conditions, and continuous perimentation have been the contributing factors.

Jan 5, 1950

By J. C. Holm

Although the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition.

Jul 1, 1956