Search Documents

By Raymond Howe

SOME time ago,, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furnace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to, the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after 4 years' service so a steam-pressed lining was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in- blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion.

Jan 9, 1919

By W. A. Griffith

Fractional replication of factorial design, a general method for planning experimentation and for analysis of data obtained, is described as applied to a flotation investigation. This method leads to determination of optimum process conditions with minimum experimental effort. Its advantages over simple factorial design are demonstrated. A METHOD for planning experimentation and for analyzing the data secured will be demonstrated. This method, termed fractional replication of factorial design, employs a relatively small number of individual experiments to determine which of a large number of process variables are controlling, to determine which combination of levels of these variables is most likely to produce optimum results, and also to predict what results will be obtained with a particular combination of conditions not already tested. Although the general method is not new, having been developed by Finney in 1945,' the extent to which it can improve the effectiveness of applied research generally has not been recognized by metallurgists. The fractional replication procedure is particularly useful in flotation experimentation and an example from such an investigation will be used in the paper. However, it has equal value in any investigation in which similar experimental difficulties are encountered. In developing a flotation process for a particular mineral separation, the investigator is inevitably confronted with the following difficulties: 1—There are a large number of potentially important process variables. 2—Results of individual experiments are not highly reproducible, due in part to the difficulty in precisely controlling all the variables. 3—Considerable effort is expended in conducting individual experiments. 4—There are practical limits on the number of individual experiments which can be made. In situations of just such a type, modern statistical methods of planning experimentation and analyzing data have their greatest value. Applications of one such technique, called factorial design, to problems of this type have been described by Dorenfeld and others.'-' The simple factorial design is an efficient procedure when the investigator hopes to provide a comprehensive understanding of the effects and interrelationships of a small number of variables over a limited range. In applied research, this is seldom the main objective. Rather, the investigator usually wishes to determine which of the many potentially important variables are in fact controlling, which levels of the controlling variables will provide opti- mum metallurgical results, and what these results will be at optimum conditions. Interest in detailed trends is limited to the controlling variables and to levels in the region of optimum conditions. Simple factorial design has serious deficiencies for such objectives and is not the most efficient method of experimental design. Deficiencies of Factorial Design In a simple factorial design, an experiment must be made at every possible combination of each level of every variable, once these have been chosen and the levels of each to be included have been decided upon. As the number of variables or levels of each increases, the experimental program quickly reaches prohibitive size. For example, an investigation of only four variables, each at four levels, requires 256 individual experiments. Often upon completion of such an extensive program, it is found that one or more of the variables has metallurgically unimportant effects or that a poor estimate has been made as to the appropriate range of levels to be investigated. The result is that only a small proportion of the data obtained falls in the range of real metallurgical interest. Indeed, it frequently can be anticipated that certain combinations of levels of variables will not produce results of interest, but they still must be included so that the essential balance, or orthogonality, of the design will be retained. It may be true that factorial design will provide the greatest amount of information from a given number of experiments, but it does not necessarily follow that it will lead to the desired information with a minimum number of experiments. Much of the information provided may be of little value. Advantages of Fractional Replication The disadvantages of simple factorial design are overcome to a great extent by a modification known as fractional replication. This is a technique for sampling systematically the potential data of a full factorial experiment, that is, the data which would have been obtained if the complete factorially designed program had been completed. Only a fraction of the total array of experiments is made, but the experiments are chosen in such a way that the important advantages of factorial design and the accompanying analysis of variance are retained. The data obtained from the first group of experiments are used to determine which of several variables are controlling and which levels of these variables are most likely to produce the desired result. Unimportant variables and levels of variables then may be

Jan 1, 1956

By Richard Maclin Stewart

A priest at Shenandoah, Pa., one day persuaded the president of the Philadelphia & Reading Coal & Iron Co. to slush breaker waste and culm into old mine workings in order to save his church from being destroyed by surface subsidence. The year was 1864, the project was successful, and history recorded the first use of hydraulic backfilling. Shortly afterward, the method was applied to several eastern coal mines for area fill to control subsidence. In 1884, hydraulic backfilling was used to control a mine fire in the Schuylkill region of Pennsylvania. The idea was taken to Europe by German engineers and developed successfully at the Myslovitz colliery in Upper Silesia in 1901. From there it was applied to several mines throughout Europe.

Jan 4, 1958

By Henry U. Ross

The behaviour during reduction of iron-ore pellets and sinters was investigated. Several methods for the preparation of agglomerates and their reduction were tried. Commercial agglomerates from world-wide sources as well as experimental samples were tested. The effect of coke additions to pellet and sinter plant feeds was given special consideration. An analysis of the test results has helped to explain many of the phenomena associated with the reduction of iron-ore agglomerates such as swelling, loss in strength and wear resistance, changes in porosity, changes in mineralogy and the formation of metallic iron and slag. A double-layer pellet with all of the coke concentrated in the core proved particularly interesting. Although large quantities of coke showed that partially reduced agglomerates containing metallic iron could be produced in the laboratory, the problem of producing reduced pellets and sinters by the existing agglomerating processes still remains.

Jan 1, 1977

By J. W. Spretnak

It is well-established that decohesions occurring at the interface of the matrix and rigid inclusions and second-phase particles are prime causes of ductile fracture initiation. It is not clear, however, how these decohesions occur. The idea that the interface bond is broken in tension is not particularly attractive when one considers the strength of such interfaces and the fact that plastic flow is not restricted under conditions of continuing flow required to initiate and propagate ductile fracture. A suggestion as to the mechanism of decohesion arises if one takes the position that, as the dislocation density increases with plastic flow and reaches some critical range of density, the phenomenon of flow can be regarded as fluidlike instead of the crystallographic motion of dislocations. As the spacing between dislocations decreases, the matrix becomes increasingly disordered in terms of loss of periodicity. At some critical degree of reduction of the periodicity, it is suggested that flow can be regarded as hydrodynamic, rather than crystallographic. Such a state has been referred to by rheologists as the "plasticized state", or the "fourth state of matter", between the liquid and solid state. A similar argument pertains qualitatively with the increase in equilibrium vacancy concentration as the temperature approaches the melting point. Taking the viewpoint that at larger strains the flow may become hydrodynamic in nature, a mechanism of decohesion is suggested. A well-known phenomenon in boundary-layer flow is that of "separation" locally of the boundary layer from the substrate.' Under certain conditions, the flow in the immediate neighborhood of the substrate becomes reversed, causing the boundary layer to separate from it. The exact condition for separation is that the velocity gradient normal to the substrate vanishes there, or It is of interest that blunt particles such as spheres and circular cylinders are most likely to give rise to separations because of unfavorable pressure distributions behind them. The source cited gives solutions for positions of separations for various geometries. In principle, such separations can also take place when metal is flowing over a "dead zone" of stagnant metal. This may explain the initiation of fracture at the elastic-plastic boundaries of plastic enclaves under a notch.

Jan 1, 1967

By David R. Mitchell, H. E. Oehler, Henry Emmett Gross

The production of fluorspar is one of the smaller nonmetallic industries in the United States with a capital investment—about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 The concentration of the coarser sizes presents relatively little difficulty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1939

By Henry Emmett Gross, David R. Mitchell, H. E. Oehler

The production of fluorspar is one of the smaller nonmetallic industries in the United States with a capital investment—about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 The concentration of the coarser sizes presents relatively little difficulty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1939

By Horace C. Porter

Most of the bituminous and semibituminous coals of this country will coke, and all of them yield, on carbonizing, more or less marketable gas and byproducts. We need, however, a finer distinction as between various grades of coking coals and between coals of different degrees of byproduct and gas-making possibilities. There is required by the consumer or the coal producer a dependable test to show whether a certain coal or mixture of coals will make coke of good commercial value for blast-furnace, foundry, water-gas, or domestic use; whether any difficulties in operation may arise from properties inherent in the coal; and whether gas and byproducts may be expected of good quality and in profitable quantity. For determining coke quality, the most dependable test is an actual run in an oven, but for byproducts a coal may better and more accurately be tested in the laboratory or in a miniature oven or retort. As to what are the most desirable qualities in blast-furnace coke, the furnace men themselves are not in complete agreement. Some desire a hard, well-burned, "hot" coke, and others get better results from a llgreener," less hardened product that burns somewhat more readily in the furnace. But certain qualities of cell structure and porosity are commonly agreed upon as desirable. Information as to what kind of coke a certain coal may be made to yield is valuable in advance, whatever may be the consumer's ideas as to the particular kind most suitable to his needs. The question arises, Can we predict coking quality with any degree of satisfaction from a small-scale test? It used to be said that coals could not be tested satisfactorily on a laboratory scale either for the coke they would yield or the byproducts. On account of the mystery with which the coking quality of coal has been shrouded and the large determining influences that many believe are exerted by mass, pressure, and the passage of carbonaceous volatile matter through the coking material, it has seemed difficult to reproduce in the laboratory the exact conditions of commercial practice. Great progress, however, has been made in recent years in elucidating the process of carbonization and many of the factors that make for the formation of high-grade coke and the recovery of the best

Jan 1, 1920

Jan 1, 1920

By J. L. Shugert, W. C. Williamson

The paper covers the different phases of dust dissemination in the Butte mines and methods of its control. Dust inspection and reporting same are taken up in detail. Methods of dust and dust counting techniques with their associated problems are discussed. Effects of different methods of dust depression are demonstrated under controlled conditions.

Jan 1, 1950

By R. F. Krueger, L. C. Vogel

A design is presented for an electrical analog computer which can solve non-steady state heat transfer problems in an extensive radial forrnation containing a moving cylindrical source. The computer is used to simulate a .simplified thermal oil recovery process in which heat transfer from a moving, constant temperature source takes place radially by conduction only. Temperature distribution curves are .shown for several different assumed modes of travel for the heat source. The data are used to estimate the residual fuel requirements necessary to maintain a self-propagating isotherma1 front for the particular system being studied. Although the computer is designed to represent an unique system. conversion factors can he adjusted to show the effects of changing the assumed values of system constants, such as thermal conductivity of the formation and temperature of the source isotherm. Examples are given to illustrate the relative influence the assumed values of these variab1es will have upon the quantity of fuel required to maintain the source. The maximum effect of heat transfer by the flowing air stream is estimated mathematically, and full requirements for this system are shown to he markedly reduced. Inasmuch as the examples discussrd refer to a simplified process, the results are not directly applicable to a practical field operation. It is believed, however, that the data il1ustr-ate some general trends which are important in thermal recovery processes. Data from laboratory and field experimentation can he used to modify the computer to take into account the influence of heat transfer by various mechanisms, for example, by injected air and by fluids ahead of the hot zone. With .such refinements it would be possible to estimate more accurately the limiting values for the rate of travel of the high temperature front and for the required air- injection rates. Use of this computer should aid in evaluating the economic feasibility of oil recovery by various thermal processes. It is hoped this paper will stimulate further work by others to help accomplish this objective. As the costs of exploration for and development of new oil fields rise. increasing the recovery of oil from established fields becomes more and more important. In fields containing low gravity crude oil, ultimate recoveries by primary means are sometimes less than 10 per cent and often total only 10 to 20 per cent of the oil in place. Conventional secondary recovery methods are not always effective in increasing this total. Methods which have been proposed for increasing the recovery of viscous oils include thermal processes for increasing the mobility of the oil. One method is to provide a moving heat source generated within the formation to heat the oil and a flowing gaseous medium (for example, air) to sweep the oil to the producing wells. The possibility of such a process has intrigued engineers for many years.'. '." but little or no information has been available in the literature relative to the technical or economic feasibility of this method. Recently, however, interest has been revived by publication of laboratory and field test results indicating the feasibility of maintaining

Jan 1, 1956

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity. Atmosphere and temperature affect the state of oxidation of the iron oxide, and the atmosphere alone may determine the ferrous minerals that finally develop. The rate and extent of cooling, the type of coolant, the subsequent handling, and screening all have serious effects upon the type of sinter that eventually enters blast furnace bins. The degree to which actual fusion or fluxing takes place in the sintering operation has a marked effect upon density. A sinter which has been extensively fused by high content of fuel in the batch will no doubt have a higher weight on the bulk basis than one which had a lower fuel content. As high temperatures are required to do this job, the iron oxide under these conditions will be largely magnetite. Sintering at low temperatures to produce larger proportions of hematite means a decrease in the amount of liquid formed and a much more sensitive bonding process. In this case the liquid must be distributed more uniformly and thereby used more efficiently than would be the case where higher temperatures were permitted to prevail more or less indiscriminately. Where coarse ore particles are used in a sinter mix it is not expected that any particles coarser than 1/4-in. can be fused and incorporated in the system to such an extent that the gangue contained within these lumps will have been converted or fused by the sintering process. It is for this reason that coarse ore, returns, or both, in a sinter usually result in a sinter which breaks easily and at the same time may contain some of the original minerals of the lump, such as quartz and hematite. In examination of sinters at Bethlehem Steel Co. minerals such as quartz and corundum have been found, none of which are considered normal associ- ates of wustite or magnetite. Some degree of heterogeneity or lack of equilibrium is not unusual in the sintering process. The differences in specific gravity between hematite and magnetite might be ample reason for poor strength in a not very well sintered mass containing coarse particles of. ore or returns. The shrinkage taking place in a lump of hematite in its conversion to magnetite by temperature and/or atmosphere is appreciable. Sintering of ores as it is carried out is crude chemistry, for the grain size is relatively coarse, the application of heat is certainly not uniform, and the time factor is inadequate for other than partial completion of reactions. Coarse lumps of coke or coal cause local heating around these centers, and fuel which is too fine may result in such slow burning that sufficiently high temperatures are not always obtained. High temperatures are essential to the work required. The Swedish practice of sintering is established on the basis of producing an easily reducible product high in hematite. This is achieved through uniformity of grain size in the sinter mix and close control of the temperature through careful regulation of fuel and sintering rates. This produces a sinter which is very tough in character and which has a high degree of porosity. Although the hematite content is not produced upon cooling by drawing air through the mass, there would be greater possibility of accomplishing this reaction with this type of sinter than is the case in American practice. In the latter, the temperatures are so high that temperature alone converts most of the mass to magnetite. The grains are so coarse in the final product that together with the fluxed condition it would be difficult to reoxidize them to hematite upon cooling. An examination of the iron-oxygen diagram' shows that hematite does not exist above 2651°F. It also shows that there is no liquid in the pure magnetite-hematite system until 2881°F is reached. On the other hand, in the system magnetite-wustite liquids exist at considerably lower temperatures than this. It will be seen, therefore, considering only the iron oxides, that the bonding action obtained in America in sinters comes about through considerable temperature and/or reducing conditions that produce compositions containing even less oxygen than is contained in magnetite or than results from the fusion of silicates. The bonding obtained from the iron oxides is encouraged by the reducing conditions that prevail in the vicinity of the fuel particles in a mass of this sort, where temperatures are above 2600°F. As magnetite and wustite are opaque, they do not lend themselves to petrographic study by transmitted polarized light. The silicates found in sinter and the glass that has not crystallized transmit light and can be studied by these methods in which indices of refraction and other optical properties of anisotropic crystals lead to their definite identification. The index of refraction is the only property that can be measured in glass under the microscope, and this is a clue to its probable approximate composition.

Jan 1, 1954

"Minerals in Transition" is the timely theme of this year's SME-AIME Fall Meeting and Exhibit, to be held September 10-12 at the Salt Palace, Salt Lake City, Utah. Approximately 2000 members and guests are expected to attend the meeting, which will include 117 technical papers, presented during 27 sessions. To complement the technical program, a record number of mining manufacturers and suppliers will be on hand to exhibit the latest in equipment innovation and professional services.

Jan 8, 1975

By F. B. Richards

THERE has been much interest recently in the iron ore supply of the Lake Superior district. It may be of interest to this meeting to give some thought to this situation, dealing more particularly with the present great iron ore deposits of this section. Ores from its various iron ranges are the foundation of the tremendous tonnage of steel and iron of all kinds produced in the territory along and adjacent to the Great Lakes, drawing the bulk of its supply from this northwestern ore country. For a number of years estimates have been made of the quantity of available ore. The latest study, by M. C. Lake, chief geologist of the M. A. Hanna Co., is of great interest and brings the estimated tonnage to Jan. 1. 1929.

Jan 1, 1930

By Akira Ishizu, Nobuo Matsui, Tatsuya Nagahama

In the concentrator of Kamioka Mine, lead-zinc bulk differential flotation is practiced. It results in three kinds of thickener over- flow, namely; tailing, lead concentrate and zinc concentrate, which are discharged as wastewater. Since these three kinds of overflow differ from each other in water quality, they are separately recycled to appropriate processes based on their water quality. The tailing and the lead concentrate thickener overflow are directly recycled to their respective suitable processes. However, as the zinc thickener overflow contains Cu(CN)3--, ZnS, CdS, CN-, xanthate and frother, the total zinc thickener overflow cannot be recycled at one time to any one process without creating harmful effects. Consequently, all the ingredients in the zinc thickener overflow other than CN- are floated by Ion-Precipitate-Ultrafine-particle flotation, using Nagahm flotation machine. After this treatment, the zinc thickener overflow, containing only CN-, is effectively recycled to the lead-zinc differential flotation circuit. Thus the integrated recycling of waste-water greatly reduces environmental problems, and in addition it generates a sizeable profit by improving overall mill recovery, and permitting the reduction of reagent consumption.

Jan 1, 1976

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman. JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS,4 BRADLEY STOUGHTON.

Jan 9, 1913

By A. D. Smigelskas, E. O. Karenna

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

By E. O. Karenna, A. D. Smigelskas

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

STANDING COMMITTEES. Executive. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS, ALBERT R. LEDOUX, BENJAMIN B. THAYER. . Membership. BENJAMIN B. THAYER, Chairman. KARL EILERS, JOHN H. JANEWAY, JR., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L. YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman1 JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALEX. C. HUMPHREYS.4 BRADLEY STOUGHTON.

Jan 10, 1913

By Richard D. Call

In any open pit, some slope instability can be expected, varying from bench sloughing to large-scale slope movement. Major slope displacements are preceded by small, but measurable, displacements and by other indicators of instability, such as tension cracks, rock noise, and changes in groundwater levels. A comprehensive monitoring pro- gram, capable of measuring and assimilating displacement related data, is essential for sound pit operation. The objectives of a pit slope monitoring program are 1) to maintain safe operational procedures for the protection of personnel and equipment; 2) to provide advance notice of instability so that mine plans can be modified to minimize the impact of slope displacement; and 3) to provide geotechnical information for analyzing the slope failure mechanism, for designing appropriate remedial measures, and for conducting future re-design of the slope. Surface displacement measurement using conventional survey equipment and extensometers has been the most widely used method, and it is still the most cost-effective. Tiltmeters and borehole inclinometers are also useful tools, and there are promising developments in micro- seismic monitoring. A monitoring system should have redundancy in both type and number of measurements, and be capable of rapid and effective dissemination of displacement information to those affected.

Jan 1, 1983