Search Documents

By S. C. Termes, P. E. Richardson, R. L. Wilfong

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble cross-linked starch xanthate (ISX). ISX is insoluble, has a shelf life of more than a year when kept cold, and has a higher molecular weight due to cross-linking than the soluble, non-cross-linked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines, but no silicious gangue. Floc formation, floc size, and settling rate are dependent on pH. The pH dependence, however, differs for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1984

By C. K. Rose, J. H. East

Proved oil shale reserves in the Green River formation in Colorado, Utah, and Wyoming dwarf present U. S. petroleum resources. Indications are that the appetite for petroleum products will continue to grow and that this potential source of liquid fuels and related byproducts cannot be disregarded. As a part of its synthetic fuels program, the U. S. Bureau of Mines has opened a mine in the richer beds on the naval oil shale reserves. In addition to supplying material for retorting and refining studies, the development of methods, procedures, and equipment for mining oil shale on a large-scale commercial basis is of the greatest importance.

Oct 1, 1955

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By James Lee Hibbard, Doraiswami Ramkrishna

A population balance model accounting for the transient variations in drop size distributions in a stirred liquid-liquid system is analyzed for its effect on chemical reaction conversion in a stirred, batch reactor. The analysis is applied specifically for phase transfer catalytic reactions, which indicates that transient effects of evolution of drop size distributions may be important in such systems.

Jan 1, 1981

By A. Dubnie

Three periods of major activity have led to the development of the present mineral industry in northern Canada. At the turn of the century, placer gold was discovered in the Yukon Territory and production has been continued to the present day. In the late 1920's and early 1930's, vigorous aircraft- aided exploration resulted in the discovery and production of radium at Port Radium on the southern shore of Great Bear Lake and of gold at Yellowknife on the north shore of Great Slave Lake. During this period, oil was discovered at Norman Wells. Present mineral production is today largely derived from deposits which have been developed in the 1950's. Among these are the re-opened deposits of United Keno Hill, uranium deposits at Uranium City, natural gas resources from the Peace River gas area, nickel-copper deposits at Lynn Lake and Rankin Inlet, and the Cassiar Asbestos deposits at McDame Mountain.

Jan 5, 1961

By W. C. Lacy

Urban development in semi-arid portions of the Southwest has upset a natural balance of geological conditions resulting in broad-scale and local subsidence or heaving ground conditions, Subsidence can be traced to two general causes: irrigation of reclaimed desert lands that have dry, low-density soils; and depression of the water table by ground water withdrawal. Accumulation of weathered volcanic tuff produces areas with swelling characteristics. Soil and subsidence studies made in the Tucson area in Arizona illustrate foundation problems typical of the Southwest that must be considered in the design of building codes. Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the arid to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area, prompted by foundation failures and breaking of buried service lines, serves to illustrate some of these relationships between the geological environment and history and engineering problems. ENVIRONMENT The desert region of the Southwest is characterized by isolated mountain ranges rising abruptly from low valleys or plains — the ranges generally occupy less area than do the intervening valleys. In southern Arizona the valley floors step up from near sea level to 2000 ft or more in elevation, and the ranges may rise to over 7000 ft. Desert and steppe-type climates predominate — climate is controlled more by elevation than it is by latitude. Both climate types are characterized by a lack of precipitation, the former more so than the latter. Practically all the rain that falls in the region evaporates; runoff or recharge generally occurs only during the wettest period. Water table levels are generally being depressed. Vegetation is restricted and consists mainly of creosote bush, cacti and sage brush on the deserts, and mesquite, pinon juniper and various types of grass on the steppes. Precipitation varies from about 3 in. on the warm deserts to about 12 in. on the steppes. Most of this falls in the summer or winter, with only rare storms in other seasons. Summer thunderstorms, often accompanied by hail, bring cloudbursts which send torrents of water streaming down the mountains onto

Jan 1, 1964

By B. W. Frazier

AT a recent meeting of the North of England Institute of Mining and Mechanical Engineers, during a discussion upon the compression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

Jan 1, 1874

By Alden Emery

SHEET-ASPHALT paving mixtures are composed of three constituents: sand, mineral filler and asphalt. An average composition of such a mixture is sand 75 per cent, filler 15 per cent, and asphalt 10 per cent, figured on a weight basis. The structural strength of the mixture at normal or high temperatures depends mainly on the mineral aggregate (sand and filler), which consti-tutes the entire framework. The filler is the finely divided mineral matter largely passing a 200-mesh sieve, added to carry the sand grading down into infinitely fine particles and so reduce voidage and increase density. The asphalt imparts cohesiveness and tensile strength, gives a certain degree of plasticity, and waterproofs the mixture.

Jan 1, 1933

By Thomas M. Chance

All gravity methods for the separation of ore from gangue, or of slate and other refuse from coal, are based upon differences in the falling velocities, in some fluid medium such as air or water, of the materials to be separated. As all materials falling in a vacuum have the same velocity, independent of the size, shape, weight or specific gravity of their individual particles, it would be more accurate to describe the operation of these methods as depending upon the retardation of falling velocities effected by the resistance of a fluid medium, this retardation being greater for small or light particles than for large or heavy particles. This generalization is true also of those appliances utilizing centrifugal force to replace or to supplement the action of gravity. The separation of materials of different specific gravities by means of a fluid having a specific gravity greater than that of the lighter particles and less than that of the heavier particles has not been applied commercially, or on a large scale, to the separation of ores or to the washing of coal, the method being limited to laboratory experimental work or to laboratory determinations for the purpose of checking up the work of jigs, classifiers, and other types of concentrating appliances. A solution of zinc chloride has thus come into general use in the laboratory to separate coal, bony coal, and slate, both to check up the work of coal-washing plants and for the purpose of making tests preliminary to the designing of coal-washing plants. The use of a heavy solution of some chemical in water has often been proposed for making such separations, especially in connection with the washing or preparation of coal. Practically insuperable difficulties, however, have prevented the commercial development of any such process, the difficulties being both physical and financial. The cost of the chemical used to make high-gravity solutions is usually prohibitive, and the freeing of the coal from all traces of the chemical is found to be practically impossible. Such solutions inevitably penetrate the individual lumps and particles of coal, transfusing into the pores and saturating the joint-planes, and very large quantities of wash water

Jan 1, 1918

By J. J. Mulligan

Introduction Coal is found in every major geographic region through-out Alaska and in two offshore areas. Since about 1852, more than 100 small mines have opened and closed. In 1981 and 1982 production was almost entirely from one mine in central Alaska. Clearly, the utilization of Alaska's abundant coal resources presents political, economic, and technical problems that are far from solution. Location and Physical Features Figure 1 illustrates the geographical and geological similarity between Alaska and the western US. Alaska's Arctic region generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of the western US. The southcentral and southeastern regions have a similar resemblance to the Sierra Nevadas and the West Coast. The Arctic, the central, and the southcentral regions have major coal fields. The southeast region has scattered occurrences. The topographic, climatic, and economic characteristics of each are different. These differences have a large effect on practical mining methods. Description of Alaskan Coal Coal deposits known in Alaska are almost all of Cretaceous or Tertiary age, much younger than the Carboniferous coal deposits of eastern and midwestern states. Consequently, most Alaskan coals have a higher moisture content and a lower heat value. Most Alaskan coals also have a much lower sulfur content. Low volatile bituminous, and anthracite coals occur in Alaska, but most Alaskan coals range downward in rank from high volatile bituminous to subbituminous and lignite. Alaskan coals are similar to coals of the northern Great Plains and the Rocky Mountains. Arctic Region Northern Alaska Coal Fields Northern Alaska coal fields are by far the largest group of coal deposits in Alaska (Fig. 2). Coal-bearing rocks extend from the foothills of the Brooks Range about 160 km (100 miles) northward to within about 80 km (50 miles) of the Arctic coast. The principal known occurrences are between the Colville River and the western coast. However, coal has been found eastward almost to the Canning River and westward under the Arctic Ocean. The northern Alaska coal fields are in a series of Cretaceous rocks that suggest a deltaic depositional environment. The beds tend to occur in series of up to eight or nine beds totaling 6-9 m (20-30 ft) of coal. However, beds 6-12 m (20-40 ft) thick have been reported, and beds 1-3 m (3-10 ft) thick seem to be relatively common. Including thin seams, coal in some places makes up about 10% of the stratigraphic section. However, no area has been explored in sufficient detail to block out any large body of reserves or to make reliable estimates of the total resource. Observation points in drill holes and along river and stream banks are few and far between. Coals in northern Alaskan fields tend to range in rank from bituminous, where moderately folded and faulted in the foothills, to subbittuminous in the gently folded rocks under the coastal plain. Coals toward the eastern extremities of the coal fields may be of Tertiary age and lower in rank, but the same general correlation between degree of folding and increase in rank can be expected. Some higher rank coals in the foothills belt are known to have coking properties but most, and possibly all, require

Jan 1, 1984

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/16 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible to maintain in stock marbles of the color, size, and thickness called for, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill such orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. 1. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By Axel Sahlin

Since the days of the infancy of metallurgical industries, slags of various kinds have been accumulating. Until a comparatively recent date hardly any employment had been found for these waste products, which have had, consequently, little or no value. An exception to this rule is the basic Bessemer slag, the value of which has become universally recognized. It is to-day one of the standard fertilizers of the world, and a price of from $15 to $20 a ton is considered reasoiable for the ground slag, which, especially in Germany, finds a ready market as fast as it is prepared. The slags from puddling and re-heating furnaces have only found vol. xx.—25

Jan 1, 1892

By George Cole

WHILE many parts of Canada's pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas in-accessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Al-though summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transporta-tion has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys oc-cupied by lakes and rivers or by many low-lying portions covered with muskeg. Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer dis-tances but it is not every water route that will satisfy the conditions of loading freight onto a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc-

Jan 1, 1940

By Research Staff ? Verde Copper Mines

FLOTATION is now commonly practiced in alkaline ore pulps, yet little is known regarding the action of the alkaline solutions on the ore particles beyond the fact that films of oxidized material form. We wish to chronicle our discovery of the presence of soluble reducing agents in alkaline ore pulps of the United Verde, and present some data on lime consumption. During the grinding and flotation of a pyritic ore containing small amounts of ferrous sulfate and other soluble salts, an excess of lime was added to precipitate the salts, and filtered samples of the solution were titrated with standard permanganate solution. Even in pulps of high causticity an appreciable permanganate titration was always obtained, in spite of the fact that the solutions were shown to contain little iron. Investigation of the cause brought about the discovery of several previously unsuspected compounds in flotation pulps made from pyritic ore. Not only the reducing agents present had to be identified, but also the amount of dissolved oxygen, and a survey was finally made of the free oxygen content and reducing agents of the mill pulp in the concentrating mill at Clarkdale. A great many. compounds might form, caused by oxidation of pyrite or other metal sulfides or by reaction between a lime solution and pyrite. The most probable compounds considered were calcium sulfides, polysulfides, thiosulfates, and polythionates. Later it was discovered in the literature that in alkaline pulp polythionates do not exist and if introduced are decomposed into sulfites and thiosulfates.1 Any precipitated sulfur is changed by alkali into thiosulfate and polysulfide. Sulfites and sulfides react to form thiosulfate, so that in the end it is possible to have in an alkaline solution only thiosulfate and an excess either of sulfide or sulfite. Confirmatory tests were made and it was finally established that the alkaline mill pulps made from the United Verde ore contained

Jan 1, 1929

An Engineers' Symposium was held Wednesday evening, Mar. 26, in the auditorium of the Engineering Societies Building, 29 West. 39th St., under the general auspices of the Local Sections of the American Institute of Mining and Metallurgical Engineers, American Society. of Mechanical Engineers, and the Society of Automotive Engineers. It was participated in by members of the American Institute of Electrical Engineers, American Society of Civil Engineers, American Chemical Society, American Electrochemical Society, American Institute of Chemical Engineers, American Society of Heating and Ventilating Engineers, American. Society of Refrigerating Engineers, New York Electrical Society, Brooklyn Engineers' Club, Illuminating Engineering Society, Institute of Radio Engineers, Municipal Engineers of the City of New York, Society de Chemie. Industrielle, Society of Chemical Industry, and the Society of Naval Architects and Marine Engineers. In opening the meeting the chairman, Gano Dunn,* said: The program calls this an engineers' symposium, which means a putting, together of things, and these things tonight are ideas of fundamental relations to the engineering profession and the engineering societies. Not only engineers, but all men nowadays are examining their views in respect to their relation to what we call Society. My conception of Society is that there is no such thing in the concrete sense of the word. It is an abstraction, and just in proportion as it is a generalization and broader in scope than the particulars from which it is drawn, so is it emptier of content. That does not mean that it is not important, but it does mean that we should be careful and not be led astray into a zeal for doing things for Society that we would not do for our fellow engineers and our brothers. The man who is unwilling to do something for his brother or fellow engineer and yet urges that same thing for Society-is thoroughly inconsistent and, in my opinion, wrong.

Jan 5, 1919

By V. Annamalai, J. B. Hiskey

The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol- 1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol- 1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 1, 1979

By H. D. Outmans

Present first-order theory for frontal stability and viscous fingering of immiscible liquids is improved by including the nonlinear terms in the equations describing conditions at the interface of the liquids. This leads to the revision of several conclusions which were based on first-order theory. They concern the growth rate and changing shape of a sinusoidal disturbance, particularly in relation to the wave number of this disturbance. Nonlinear aspects of effective interfacial tension are discussed and it is shown that this tension is not simply a positive proportionality constant in a linear relation between pressure difference and curvature at the interface. Scaling requirements are determined from the dimensionless groups which govern fingering. Gravity and interfacial tension invalidate a previously formulated conclusion that the shape of a finger after a given displacement is independent of the displacement velocity. Also, similarity of fingering (and, hence, of sweep efficiency in case of an unstable front) requires geometrical similarity of the initial disturbance in the model and the reservoir with a scale factor which is the same as the one for scaling down the dimensions of the reservoir. INTRODUCTION The critical velocity at which the transition zone in the vertical displacement of immiscible liquids becomes unstable was calculated by ill. More recently, the same was done for nonvertical displacements and it was also shown that the stability is affected by an effective interfacial tension between the liquids. 2-4 Although in the oil reservoir a stable front is always desirable from a recovery point of view, the necessary velocity may have to be so low that the corresponding production rate is not economical. In that case, a knowledge of the fingering unstable front is necessary for predicting recovery at break- through. Studies in this direction have not gone beyond the very moment at which fingering first occurs.5,6 Conclusions about stability and fingering in these references are all based on linear theory. In this theory the nonlinear terms in the equations describing conditions at the front are neglected. The usual justification for this lack of mathematical rigor is that the nonlinear terms can be made small relative to the linear terms and, supposedly, small causes produce only small effects. It has been recognized, however, that this is not necessarily true in the nonlinear problems of hydrodynamics.7 The hydro-dynamic stability and fingering of the front between two liquids, accelerated in a direction normal to the front, for instance, is strongly influenced by the nonlinearity of the boundary conditions.8-10 Since these boundary conditions are not unlike those arising in the problem of stability and fingering of the front during a slow immiscible displacement in porous media, it was thought that there, too, the nonlinear terms should be taken into consideration. A summary of the results obtained in linear theory and a comparison with experimental data precede the nonlinear theory developed in this paper. This summary serves to introduce some quantities which will be used in the further develop ment. It should also be pointed out that the method of higher-order approximation by which the nonlinear stability problem is solved has application in other reservoir studies.11 SUMMARY OF LINEAR THEORY 1. A plane interface remains stable if its velocity is smaller than a critical velocity. vc = (p2-p1)gn/(l/A2- l/A1 .........(1.1) This equation is derived for uniform flow in a thin layer inclined to the horizontal plane. The displacement takes place in a direction normal to the intersection of this layer and the horizontal plane. The undisturbed (line) interface is normal to the velocity. Fluid 1, the upper fluid (gas), is displacing Fluid 2 (oil). (VcQS would be the injection rate in cc/

By Walter Mueller

Transition in the underground coal industry, begun with the passage of the Federal Coal Mine Health and Safety Act of 1969, should be completed midway in the 1972-80 period. Surprisingly, many of the far reaching effects of this act have been, for the most part, beneficial to the industry from the standpoint of health, safety and basic operating standards. Production has dwindled, but the next few years will see production declines level out. Average declines of approximately 27% have been recorded since passage of the 1969 act, with costs increasing an average of $1.50 per ton throughout the industry. Nationwide averages presently are in the range of 14 tons per man-shift, and by 1980 this may be further reduced to a 10-ton per man-shift average for the industry. But in spite of the many temporary set-backs affecting the industry, the marketing opportunities are clearly visible. Due primarily to the energy squeeze facing the U.S. over the near term, the &apos;underground coal operator is and will be enjoying unusual leverage in selling his product.

Jan 10, 1972

By Courtenay de Kalb

The following observations upon onyx-marbles are fragmentary, and may shortly be rendered superfluous by the appearance of a work upon these interesting stones by Prof. George

Jan 1, 1896

By L. W. Pommier, F. B. Brien

In order to determine the ability of cyclones with heavy liquids to preconcentrate ores, a study of the variables which govern the behavior of the solids in the apparatus has been made. To assess the test results, the cyclone products have been examined by sink and float analysis at various specific gravities and the results examined by the Tromp type curves. This analysis has allowed the development of the SG50 unit — specific gravity of the particles, 50% of which goes to overflow and 50% to underflow — rather than the d50 (size) unit used in classification. The results of tests using the closed circuit laboratory cyclone assembly with dry feed samples show the validity of the equation: Results indicate that 83% of the feed may be rejected containing 0.1% Sn. Recoveries in excess of 80% are obtained at a grade of 1.7% Sn from feed samples assaying 0.4% Sn. As water-wetted particles may comprise the plant feed, separate tests were performed to examine the effect of water in the feed material. Results indicate that the entrained water divides into two fractions, one of which is defined as free water and is rejected to the cyclone overflow, the other fraction forms an adhering envelope of water on the ore particles, altering their effective size and density. The presence of the envelope of water on the particles increases the ease with which the heavy liquid can be recovered but decreases the concentration efficiency. It is proposed that the detrimental effect of water in the cyclone may be minimized by using a higher feed pressure cx by the use of surfactants. A higher feed pressure, by increasing shearing forces, would reduce the thickness of the water envelope on the particles. The surfactants, by adsorbing on the particles and producing hydrophobic surfaces, would displace the water envelope and allow the heavy liquids to wet the modified surfaces. In both cases a larger proportion of the entrained water would report to the cyclone overflow as free water, thus minimizing the detrimental effect of water on the concentration efficiency. Additional testing is required on the behavior of water in the system; to determine the optimum particle size for the preconcentration step; to determine final particle size for optimum liberation and subsequent treatment of the products in present plants and to determine the efficiency with which the heavy liquids may be recovered from the products. For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Boliva today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since heavy liquids are now available with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined. THEORY AND TECHNICAL CONSIDERATIONS Three types of heavy liquids are available: aqueous solutions of very soluble salts, salts or mixtures of

Jan 1, 1964