Search Documents

By E. S. Leaver

THE amount of gold that occurs in a ton of milling ore from most of the large-scale copper mines is so small that unusual care and special attention are necessary to recover it. In some cases the gold is not considered important enough to warrant daily assays of the various products. Considering the large tonnage of copper ores that are now concentrated by flotation, as computed in a recent review, the gross gold content is surprisingly large, probably amounting to over 10 million dollars per year in the United States. The indications are that in many of the copper-milling operations with gold content under $1 per ton, only 50 per cent. of the gold is recovered in the flotation concentrates. Lime is generally used as a depressant for pyrite in the flotation circuit. The authors have shown that high lime or a solution high in calcium ions is also a depressant for gold. Their experiments on several well-known ores show that by careful regulation of the alkalinity of the mill solutions, a higher flotation recovery of the gold can be obtained, together with equally good copper recovery in a good grade of copper concentrates. In cyanidation for the recovery of gold, the best accepted practice demands that the mill solutions be tested and regulated by simple chemical reactions at definite periods during treatment or with each change in the treatment. It is similarly important for the recovery of gold that the solution in the flotation circuit be analyzed for calcium ions at regular periods and at each step in the flotation practice. The lime should be added when and where needed and not in excessive amounts at the head of the mill.

Jan 1, 1931

By H. A. Bauman, T. S. Spicer, C. C. Wright

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 2, 1950

By E. L. Swarts

In the course of a program on high-temperature processing and electrowinning of uranium at the Knolls Atomic Power Laboratory,'' it became necessary to give attention to the interaction of molten uranium with graphite. Although it is known3 that a protective interface layer may form, details of this reaction have not been reported. Unfortunately it was impossible to complete the planned experimental program. However, the general problem is considered of sufficient interest to warrant reporting those preliminary results actually obtained. EXPERIMENTAL PROCEDURE Interface carbide layers were formed by melting samples of cleaned uranium metal in small closed graphite crucibles. Equilibrations were conducted in vacuo or in an atmosphere of dry helium at temperatures ranging from 1150" to 1400°C and for periods of from 24 to 240 hr.

Jan 1, 1960

ALBERT J. PHILLIPS, Chairman E. H. Dix, JR., Past-chairman R. H. LEACH, Vice-chairman R. F. MEHL, Vice-chairman W. M. COME, Treasurer LOUIS JORDAN, Secretary 29 West 39th St., New York, N. Y.

Jan 1, 1937

By L. G. Austin, P. T. Luckie

The Bond Work Index has been used for many years to estimate the power requirement of a material with known work index. The index is determined by a completely empirical test and no logical base for its use has been formulated. However, consideration of grinding as a unit operation which can be mathematically treated offers the prospect of considerably more accurate design and mill power estimation when sufficient data on large-scale mills becomes available. The interrelation of the Bond type with the unit operation approach is discussed.

Jan 1, 1973

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method.

Jan 8, 1950

By S. F. Emmons

In the yew 1879, Congress, acting tinder the advice of tile National Acdemy of Sciences, discontinued the temporary surveys or explorations under Hayden, powell, and Wheeler, and established as a permanent organization the United States Geological Survey, making it a Bureau of the Interior Department. A great step was thus taken toward obtaining the greatest practical results from the expenditure of the public money for geological purposes. The recommendations of the National Academy also contemplated the consolidation of all the various organizations for the mensuration and mapping of the country—-such as the Coast, Engineer, and Land Office Surveys—under one single head; which, also, should assume the duty of providing the mays necessary as a basis fir the work of the Geological Survey. But this useful measure did not meet the approval of Congress, and the various mensuration surveys were left in statu quo. With the final establishment of a permanent Geological Survey of the United States, it became necessary to adopt a plan of work which would enable it in time to take the prominent rank among the older surveys of other civilized nations of the world, which is justified by the great, wealth and mineral resources of the country it is destintd to study. The somewhat vague wording of the organic law under which it was created, directing an examination of the geological structure, mineral resources, and products of the public domain, left the details of the policy to he pursued very largely a matter of discretion with its director. That adopted by Mr. Clarence King, the first director, as foreshadowed in his Annual Report to the Secretary of the Interior for 1880, was one whose distinguishing feature was the prominence that should be given to economical geology, or the practical application of geological investigations to the development of the mineral resources of the country. In earlier Government Surveys, which were topographical reconnoissances in a practically unknown region, geology occupied a secondary and unimportant position. With the Fortieth Parallel Survey, inaugurated in 1867, and its successors, the Hayden, Powell, and Wheeler Surveys, geology became an essential object of the work, but owing to the want of already existing maps topography

Jan 1, 1882

By John H. Stewart, Daniel R. Shawe

Major transverse structural zones in the western U.S. such as the Lewis and Clark line, Walker Lane, Texas lineament, and Colorado mineral belt, have localized important mineral districts. In Nevada and Utah the alinement of Cretaceous and Tertiary mineral deposits, such as in the Pioche, Eureka, Manhattan, and other mineral belts, may be related to similar tectonic features. All the mineral belts in Nevada and Utah have produced precious and base metals and tungsten; the Manhattan belt in addition has produced magnesite and brucite; and the Pioche belt, uranium, fluorspar, and alunite. Specific types of ore deposits seem related spatially to major belts of the Paleozoic Cordilleran geosyncline and compositionally to the intrusive bodies with which they are associated.

Jan 1, 1977

By Richard P. Schoemaker

Introduction In underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to in-homogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. The Pressure Dome Theory The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1949

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported' . and will not be repeated here. The experimental methods employed in the investigation have also been covered.'-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger' in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger's diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By Franklin Moeller

Considering the really short time that has elapsed since hydro-metallurgical processes of extracting copper from ores have been extensively developed, and the large scale on which this method is practised at Ajo, the successful operation of the plant must excite the admiration of every visitor. The application of the mechanical unloader to the purpose for which it is employed at Ajo is but an extension of the use for which it was originally designed, some 20 years ago, for unloading iron-ore vessels at the lower lake ports. At a time when the maximum output of a single machine, with men shoveling the ore into buckets, did not exceed 40 tons per hour, G. H. Hulett invented and constructed a mechanical unloader with a bucket of 10-ton capacity. This machine was of the steam hydrauIic type, and it is still in operation after nearly 20 years of service. Several more machines of the same type were built, but the difficulties of power transmission, and the rapid development of electrical machinery, soon led to the adoption of electrically operated machines, and practically all of the later installations have been thus equipped. This electrically operated unloader has proved so well fitted for the work that the design of the lake boats has been practically revolutionized, with special view to the ease and rapidity of unloading. It is now possible to unload a 12,000-ton vessel with four machines in a little over 2 hr. This has necessitated an increase in the capacity of the machine, and the largest yet built handles an average load of 17 tons, with a possible maximum of 20 to 21 tons. The Ajo excavator is somewhat simpler in design than the iron-ore unloader, in that it is not provided with a larry. In the unloader, the iron ore, picked up by the bucket, is delivered to a larry or transfer car which runs in the lower chord of the bridge; the larry then delivers the ore either into railroad cars, standing on several parallel tracks, or into the stock pile, thereby saving the time that would be required for the bucket to make the trip. At Ajo, the bucket delivers the tailing

Jan 1, 1920

By D. L. Garthwaite, F. M. Stewart, F. K. Krebill

Pressure has been maintained in the Elk Basin Ten-deep reservoir since the initiation of inert gas injection in Sept., 1949. Oil is being produced under conditions favorable for gravity drainage, including high angle of dip, appreciable structural closure, and fairly good per~neability. Results being obtained are high per cent recovery of oil-in-place, sustained field productivity, reduced operating problems, and recovery of plant products. The high recovery has been calculated by alpplication of the gravity drainage theory described in an earlier AIME paper.' It is also confirmed from field performance by comparing nil recovery to date with gas cap spuce voided. GENERAL INFORMATION The Elk Basin field lies in Park County, Wyo., and Carbon County, Mont., approximately 50 miles east of Yellowstone Park. Located at the northern end of the Big Horn Basin. the field is situated on an elongated asymmetrical anticline (Fig. 1). The pressure maintenance project covered by this paper involves the Embar-Tensleep reservoir in this multi-pay field. Discovered in Nov., 1942, it has a proved productive area of over 6,300 acres. It consists of the 210-ft thick Tensleep sandstone of Pennsylvanian Age overlain by 40 ft of Embar dolomite of Permian Age. The two formations apparently are in communication with each other and are produced as a common source of supply. As 98 per cent of the reserves are contained in the Tensleep sandFtone, in this paper the Embar-Tensleep reservoir will he called simply the Tensleep. The reservoir is found at an average depth of 4,900 it, is approximately 7 miles long and 2 miles wide, and has a maximum oil productive closure of 2,330 ft. The strata dip an average of 21" on the west flank and 45" on the east. There are presently 132 Tensleep wells in the field drilled on 40-acre spacing; of these, 17 are shut in because of high gas-oil ratio (GOR) and eight are gas injection wells. Rock characteristics and related information for the pay section follow: Porosity, avg 10.7 per cent Permeability (air) from cores, avg 118 mds Permeability from PI'S 91 mds Connate water, avg 8 per cent Initial pressure (-400 ft) 2,234 psia Pressure April 1954 (-400 ft) 1.327 psia At high structural positions much of the better sandstone has connate water content of only 2 to 5 per cent as indicated by the coring of wells with oil in nearby Tensleep fields. In special imbibition tests, samples readily imbibed oil but repelled water. In tests on crushed samples, the sand grains rapidly settled in oil and carbon tetrachloride but formed a stable unsinking floc in water. This information indicates that the Tensleep sand is preferentially oil wet. The oil produced averages 29' API gravity and has a high sulfur content. Extensive sampling and testing have established the fact that characteristics of reservoir oil in this field vary greatly with structure, see Fig. 2. Additional detail on the variation of oil characteristics with structure at Elk Basin may be found in Reference 2. At original reservoir pressure the oil was undersatu-rated with gas, the bubble point being 1,250 psi at the crest but only 500 psi at the lowest elevation sampled. As noted on Fig. 2, other fluid properties—reservoir volume factor. solution ratio, gravity, viscosity, and hydrogen sulfide content—likewise vary greatly. These variations complicate mathematical analysis, for it is necessary to average these characteristics in order to enter them into reservoir engineering expressions. To further complicate analysis, sand-face pressure also varies greatly because of the increase in fluid head down structure. As an approximation, average properties under initial conditions may be read from Fig. 2 at the -450-ft elevation.

Jan 1, 1956

By R. E. Wade

The Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. & P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 1, 1914

By R. S. Handy

AT THE TIME of my first visit to Bolivia in 1927 the tin-mining industry was prosperous, the tin price at London being more than £300 per long ton of tin, and the operators were making every effort to bring their plants up to the very highest point of capacity as well as of efficiency. Any device or piece of equipment or method that gave promise of increasing production was welcomed regardless of the cost, and the plants were being modernized as rapidly as human ingenuity could make it possible. At the time of my second visit in 1932, however, conditions had changed materially. The price of tin had fallen to a little over £100 but costs had not decreased anywhere in proportion and operators were at their wit's end to cut the operating losses that were everywhere prevalent. Charles L. Bradbury, manager of the Empresa Minera de Huanuni, at Huanuni, Bolivia, had been recently called from Mexico to make all analysis of the situation and to attempt to work out a remedy for the economic conditions that threatened to close the mine. His analysis brought out the following points:

Jan 1, 1938

By M. Stern, I. S. Servi, W. W. Webb

ZINC has been considered an ideal material for investigations of the behavior of dislocation walls in metals. It has appeared particularly useful for studies of the mechanisms of plastic deformation and the motion of low-angle boundaries under stress, because orientated crystals are easily grown and cleaved. Moreover, the hexagonal structure makes the introduction of controlled tilt boundaries relatively simple. Apparently, another of the many reasons for selecting zinc as a working material is its commercial availability at the 99.999' pct purity level. However, most elements are only slightly sol-

Jan 1, 1959

By L. Adler

A fairly complex analysis is required to select or evaluate a piece of excavating and bulk handling equipment for its performance. At present, there is little agreement as to what points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment. The importance of the equipment characteristics, job activities, and work conditions are stressed. Separate analytical stems are established in a flow chart for these. They are combined using suitability tests in: problem statement; natural conditions; suitability guidelines; appropriate equipment types; operational activities; encumbered space; geometric design; equipment sizing; failure and limits; performance and consumption; public policy checks; and costs and profitability. Public policy and economics receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1985

By W. Griffith

The purpose of this paper is to make public record of new information in regard to the sustaining power of artificial mine-roof supports (not timber props), the result of investigations recently made in the anthracite coal fields of Pennsylvania. First.—By the "Scranton Mine Cave Commission," appointed to investigate the mining conditions under the City of Scranton. Second.—By the "Pennsylvania Mine Cave Commission," appointed by the Governor to investigate the general subject of mine caves in the anthracite region of Pennsylvania. Third.-—By the personal researches and tests made by the author in an effort to secure a better artificial mine-roof or surface support. During the progress of the work of the Scranton Mine Cave Commission, the Engineers for the Commission, Messrs. Conner and Griffith, being aware of the general lack of exact information in the engineering profession as to the strength of the ordinary artificial mine-roof or surface support, and particularly the stronger kinds, such as mine cogs, rock piers, etc., had tests made at the Fritz Engineering Laboratory at Lehigh University, to determine the sustaining power under various compressions of the several kinds of artificial mine supports in use in the anthracite region of Pennsylvania. A report of these tests wasincluded in the report of this Commission, which was published as Bulletin No. 25 of the United States Bureau of Mines, Washington. A similar series of tests, more extensive and more elaborately planned, were subsequently made for the Pennsylvania Minc Cave Commission at the U. S. Government Testing Laboratory at Pittsburgh, Pa. The report of this Commission was made to the Governor, but has not yet been published. The author, during his connection with the Scranton Mine Cave Commission, observed that of all the various devices employed for sustaining the roof of coal mines, the one universally used and the best

Jan 1, 1918

By Jeremias K. Chitunda

Significant cost savings and improved ground stability are two initial indications from the current wet process shotcrete ground support program at the Lakeshore mine. The area of shotcrete for ground stability is not strange to the Lakeshore operation. Since the beginning of the project, various shotcrete techniques have constantly been experimented with, incorporating all the latest technological developments. Over the years, the use of shotcrete has been employed as a primary, temporary, or permanent support, singly or in combination with rockbolts and steel sets. The extent of shotcrete usage compared with steel sets and rockbolts has varied from time to time as dictated by the overall state of the art. In 1972, for example, the ratio of the linear drift footage supported with shotcrete to that supported with steel sets averaged 1.0. In 1973, that ratio was about 3.0. Overall, for the Lakeshore mine, there are about 8000 drift ft of shotcrete, 8000 drift ft of steel sets and timber, 750 drift ft of formed concrete, 21,000 drift ft of rockbolts, and 3700 drift ft of combined type support.

Jan 12, 1974

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949