Search Documents

By Robert Henderson

SEVERAL very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. THE ORE BODY The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. MINING SYSTEMS For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the

Jan 1, 1944

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery'.' have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By M. A. Orehoski, J. M. Hodge

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By J. M. Hodge, M. A. Orehoski

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By Lillian Erskine

While brass and other copper alloys have long been listed as offering health hazards to their workers, it is questionable if the metals involved are alone responsible for the trades' records of morbidity. The entire science of foundry sanitation is the product of the past two decades; and the best standards now operative would have been regarded as little short of revolutionary prior to 1910. The special handicap to the conservation of the health of the brass founder's employees has been the fact that, unlike the iron founder, his business could be profitably carried on in almost any small and unsanitary quarters. As a result, writers on occupational disease have accepted brass chills or brass founders' ague as an inevitable feature of the trade; and respiratory disabilities, as well as phthisis and disturbances of the nervous system, are also included as prevalent among those employed. While there can be no question as to the basic accuracy of past investigations, there is every reason to doubt the necessity for an undue percentage of ill health among brass molders and casters who are safeguarded by scientific ventilating standards and by improving personal habits of sobriety. There is, however, need for a campaign of education as to the most approved practices and equipment whereby the employer may safeguard the health of his workers, and thereby reduce his labor turnover and increase his productive efficiency. Broadly speaking, copper, tin, and aluminum carry negligible health hazards. The toxic qualities of lead, however, are a menace; especially if scrap lead is recovered or bought for foundry processes. The rapid volatilization of zinc renders its fumes and flocculent condensation the chief problems in conserving the health of the brass worker. The frequent presence in the foundry air of traces of arsenic compounds, lead

Jan 1, 1919

By B. Egeberg

BRITANNIA metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two, other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375° F., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later.

Jan 1, 1928

By C. M. Wayman, M. A. Gedwill, C. J. Altstetter

Cobalt Whiskers were grown by the hydrogen reduction of CoBr,. The fcc = hcp martensitic trans-formation in these whiskers was studied using X-ray and metallographic techniques. Present theories of the fee + hcp martensitic transformation were ex-amined in the light of the present findings Experimental evidence for slip as a part of the transformation mechanism is presented. In the bulk form cobalt is known to undergo a martensitic transformation1 from an hcp to an fcc structure upon heating above about 430°C. Upon cooling, the reverse transformation starts at about 400°C, but does not go to completion except in single crystalline or coarse-grained samples, or upon plastic deformation. The transformation may be thought of as the shearing of close-packed atomic planes in such a way as to change the stacking sequence from ABCABC to ABABAB with a contraction normal to the shearing planes and an expansion in the planes,2 producing a c/a ratio slightly less than ideal. This restacking to give {0001) and (112) 11 (1010) can be accomplished by the passage of a shockfey partial dislocation over every other (111)f plane resulting in a theoretical shear of 19.47 deg. To date there has been no completely satisfactory explanation of how the partial dislocations are produced on the close-packed planes or propagated from plane to plane to give the correct stacking sequence. The object of the present research was to study some of the characteristics of the fcc to hcp transformation in geometrically simple single crystals. It was felt that whiskers of cobalt grown by halide reduction would be ideal specimens with which to study the transformation, because whiskers have the following desirable features: 1) are easily grown as fcc single crystals; 2) exhibit relatively simple geometries; 3) have comparatively low dislocation densities;

Jan 1, 1964

By Derek C. Shelton

This chapter covers the preparation of specifications for a dry crushing and wet grinding comminution circuit.

Jan 1, 1982

By Lewis Delano

IT HAS been generally recognized that, owing to the extreme friability of, galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth retreating today. Investigations of the work of the Hancock jig on the Bonne Terre ore- have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average over all conditions and grades of ore will be between .0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increased smelting charges; due to a greater amount of slime galena will be counterbalanced by the lower operating cost, in-creased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the' St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various flow sheets, and to calculate the economics of the problem' with great accuracy. .

Jan 8, 1920

By Lewis W. MacNaughton, F. L. Burchard

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Coolie, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. DevELopments during 1941 Nearly 1600 wells were drilled in the district during 1941 as compared with more than 1700 in 1940. However, the ratio of successful drilling operations was higher and some 1200 oil wells were completed. Production held about even with the previous year, as did the number of producing oil wells. Known oil reserves increased slightly throughout exploration, which generally was carried on at greater depths than in former years. The average depth of discovery wells was 300 ft. deeper than in 1940. Although discoveries were evenly divided numerically between horizons above the base of the Strawn series and those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the increase in oil reserves. The largest single addition to the reserves was in the Ellenburger formation in the K.M.A. field. During the year 112 wells were completed in this horizon, bringing the total developed acreage to some 4600 acres. The Straan series in K.M.A. also received considerable development in 1941, with 114 completions. K.M.A. Pressure Maintenance Satisfactory progress was made by the K.M.A. Pressure Maintenance Association in 1941. At the end of the year, 99 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 340,548 M cu. ft. in December from a low of 208,853 M cu. ft. in February. Total volume of gas returned during 1941 was 3,306,052 M cu. ft. To the end of the year, 150 cu. ft. of gas had been returned for every barrel of oil produced from the reservoir while the input ratio for December was 397 cu. ft. Per

Jan 1, 1942

By F. L. Burchard, Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Coolie, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. DevELopments during 1941 Nearly 1600 wells were drilled in the district during 1941 as compared with more than 1700 in 1940. However, the ratio of successful drilling operations was higher and some 1200 oil wells were completed. Production held about even with the previous year, as did the number of producing oil wells. Known oil reserves increased slightly throughout exploration, which generally was carried on at greater depths than in former years. The average depth of discovery wells was 300 ft. deeper than in 1940. Although discoveries were evenly divided numerically between horizons above the base of the Strawn series and those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the increase in oil reserves. The largest single addition to the reserves was in the Ellenburger formation in the K.M.A. field. During the year 112 wells were completed in this horizon, bringing the total developed acreage to some 4600 acres. The Straan series in K.M.A. also received considerable development in 1941, with 114 completions. K.M.A. Pressure Maintenance Satisfactory progress was made by the K.M.A. Pressure Maintenance Association in 1941. At the end of the year, 99 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 340,548 M cu. ft. in December from a low of 208,853 M cu. ft. in February. Total volume of gas returned during 1941 was 3,306,052 M cu. ft. To the end of the year, 150 cu. ft. of gas had been returned for every barrel of oil produced from the reservoir while the input ratio for December was 397 cu. ft. Per

Jan 1, 1942

By Raymond B. Ladoo

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives; for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive. may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster, that the ultimate cost will be less. It is on this basis that artificial abrasives have largely replaced natural abrasives for grinding metal. Classification Abrasives may be divided into two general classes, natural and manufactured. The former includes all rocks and minerals used for abrasive purposes without chemical or physical change other than crushing, shaping or bonding into suitable forms. Manufactured or artificial abrasives are made either by heat or chemical action from metals or mineral raw materials. On page 2 is a list of the most important abrasives, classified as to inherent types and as to forms in which they are used industrially. For most types of use there are manufactured products that can be substituted for the natural products, usually at higher initial

Jan 1, 1960

By Albert Mendelsohn, Charles F. Jackson

The system of stoping described in this paper was first introduced at the Champion mine of the Copper Range Co., Painesdale, Mich., in 1929, and since that time has been developed to a high state of efficiency. The method was devised to overcome some of the objections to the system of horizontal cut-and-fill stoping formerly employed at this mine and has done so successfully. The objections to the old system became more pronounced as the depth of mining operations increased and a change became a matter of necessity. While the combination of conditions encountered at the Champion mine is rather unusual, it is believed that the sublevel system developed there could be employed advantageously at other mines, though certain modifications might be necessary. This paper describes the method and the results obtained through its use, and suggests modifications for making it applicable under quite different conditions from those at the Champion mine. Champion Lode The lode being mined at the Champion mine is the heavily brecciated top of what is known in the district as the Baltic lava flow. The brecciated portion of the lode varies from 6 to 50 ft. in width. Under this breccia is the thinner, tighter, amygdular portion of the lode; under the amygdular portion is the trap footwall. Native copper is found deposited in the rock fragments of the breccia, in the cementing material of the breccia, in the amygdules and in the trappy rock under the amygdular part of the lode. In some places masses of copper many tons in weight extend far into the footwall of the lode. The Baltic lode on Champion property is 8000 ft. long, very straight along the strike, and dips uniformly 70' to the west for 3000 ft. in depth, at which point the dip begins to flatten slightly. The width of the copper-bearing portion of the lode varies from 10 ft. to as much as 80 ft. in a few places; the average width now mined is 17 ft. The lode rock is hard—the standard one-man drilling machines used in the mine drill from 10 to 14 in. per minute when mass copper is not

Jan 1, 1932

By Frank Feuille, Edward Schuster

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923

By Edward Schuster, Frank Feuille

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923

By Dave H. Barnett, Brij M. Moudgil

The flotation technique as employed by Florida phosphate producing companies for the beneficiation of fine phosphate particles has been standardized over the years. Lower recoveries of coarse Phosphate rock by froth flotation technique, however, led to the development of new methods based on skin flotation of phosphate agglomerates. Recent developments of floating coarse rock in large flotation machines have not yet convinced the rock Producers of their higher separation efficiency. It is interesting to note that the selection of a particular machine is still bared on equipment preference by an individual company as well as proven performance of a particular machine for upgrading a specific material. Various techniques which have been developed to beneficiate the coarse phosphate rock have been discussed. Performance of the individual techniques is presented.

Jan 3, 1979

By Rodolfo V. de la Cruz, Richard E. Goodman

Knowledge of the initial state of stress in rocks provides a key to the solution of many problems in rock mechanics. The initial state of stress is part of the basic data required for rational design of structures in rock, since its redistribution when engineering activities are conducted is a primary load on the rock portion of the engineering system. Knowledge of initial and subsequent changes in the state of stress is also relevant in the study of active faults and crustal strain. The purposes of stress measurements are not generally well served by methods which disclose only one of the stress components at a point. Recently, interest has centered on overcoring methods which though ex- pensive and difficult have the important advantage of yielding data on three or more stress components. In a previous paper, the authors introduced a new method-termed borehole deepening-based on measurement of the deformations that occur close to the bottom of a borehole when it is deepened by further drilling without overcoring.l The proposed method is at a disadvantage when compared with over- coring procedures in that the quantities to be measured are somewhat smaller and the measuring environment is more hostile. However, the borehole deepening method presents three distinct advantages in comparison with overcoring procedures: (1) Using the same borehole, both the initial and the subsequent changes in the state of stress can be obtained by borehole deepening. Stress changes with time are

Jan 1, 1970

By A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except .conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By V. F. Swanson

A petrographic study was made of the type and sources of mineral contamination occurring in Florida phosphate rock products. Emphasis was placed on contaminants in the screened rock (+1 mm), since this portion of the product undergoes no physical beneficiation except for scrubbing to remove slimes. Since iron and aluminum contents of the finished product affect the salability, special emphasis was placed on identifying types and sources of these contaminants and relating chemical composition to visual characteristics. Wavellite derived from the overburden was the major aluminum contaminant with some aluminum being included as secondary clay balls. Iron occurred as phosphates in the overburden and as colloidal oxides included in the phosphate pebbles. Chert and limestone contamination derived from the Hawthorne formation underlying the phosphate matrix.

Jan 1, 1972

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917