Search Documents

By J. H. Keeler

QUESTIONS raised during earlier investigations of the preferred orientation in titanium1 and zirco-nium sheet led to the examination of the rolling and annealing textures of beryllium and hafnium sheet. Since the c/a ratios are 1.568 and 1.584, less than that of ideal close packing, 1.633, it would be expected that the preferred orientations would be similar to those exhibited by zirconium and titanium. This was found to be true. However, in several regards the orientations observed for beryllium differed from those reported by Smigels-kas and Barrett4 and so are given here. The okientations for hafnium are presented since only the cold-rolling texture has been reported in the unclassified literature. The pole figures were determined by transmission using an X-ray spectrogoniometer with copper Ka radiation and the automatic pole-figure recorder designed by Geisler described previously.6 The intensity units in the pole figures in this case are only arbitrary since calibration against a random sample of the same material was not considered necessary for the original purpose of the examination. The beryllium sheet, cold-rolled from 0.036 in. to 0.006 in., a reduction of about 84 pct, exhibited a split texture with the [1010] direction in the rolling direction as shown in Fig. 1. The same specimen annealed in vacuo for 1 hr at 1000°C showed no change in orientation. These textures

Jan 1, 1959

By Jack Parker

There are some simple theoretical approaches to pillar design but they leave much to be desired. There are also more complex theoretical approaches, but at this time the most realistic approach is to go into the mines and observe and measure how real pillars are performing under real conditions; to allow the information thus gathered to ferment in our minds - then to project the behaviour of those pillars into our new designs and mining techniques, probably with no formulas at all. Examples, from half-a-dozen different mines, show how a simple- minded approach, through observation and measurement, led to changes in pillar design which often contradicted the textbook but made very significant contributions to mining safety, efficiency and costs. The good news is that we know a lot more about pillar design than we realize. We have, between us, looked at millions of pillars of all kinds, under all conditions, but we have overlooked what they are trying to tell us. We can take problem situations and turn them into opportunities and, in that way, become better stewards of the resources which have been given to us.

Jan 1, 1983

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

Jan 1, 1904

By Orville Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually increases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal.

Jan 5, 1951

By A. R. Denison

The Permian Basin as it appears in the title of this article refers to three rather widely separated areas of production. It includes what are commonly known as the "Panhandle" fields of the northwest part of Texas; the West Texas fields, in the southwest part of Texas; and the New Mexico fields, in the southeast corner of New Mexico. These three areas are all included in a single province and produce the majority of their oil from limestones or dolomites of Permian age. The manner of accumulation of oil in the three areas is somewhat diverse. In the Panhandle, production is found on the flanks of an enormous structural ridge, the core of which is granite. In southwest Texas and New Mexico oil is produced from both gentle and steep folds and from lenticular areas of porosity. Production in Texas During 1927 Texas produced a total of 216,306,000 bbl. of oil of which the Permian Basin contributed 89,797,000 bbl., or 42 per cent. During 1928, Texas produced 255,021,000 bbl. of oil of which the Permian Basin contributed 145,955,000 bbl., or 57 per cent. The increase in total production is entirely due to the West Texas fields. All other districts in Texas declined during the year while the west Texas fields registered an increase of more than 71,000,000 bbl. West Texas daily average production increased from 260,752 bbl, at the beginning of 1928 to a maximum of 406,318 bbl. per day the first week in May. Due to prora-tion agreements, the production was held at a fairly constant level around 340,000 bbl. during the remainder of the year, having 345,660 bbl. the last week in December. Daily average production of the Panhandle fields decreased from 80,178 bbl. at the beginning of the year to 59,025 bbl. at the close of the year. The combined daily average production of the Panhandle and West Texas fields at the beginning of the year was 341,138 bbl. and at the close of the year was 405,408 barrels. Fig. 1 gives a comparison of the production in the Permian Basin in relation to the production of the entire state. It is clearly shown that

Jan 1, 1929

By Abdel Kadir Attia, Haydn H. Murray, Adel Abdel Azin, Sabah N. Boulis

An extensive reconnaissance survey of bentonitic clays in Egypt was carried out from 1982 to 1984. X-ray diffraction, differential thermal analysis, electron microscopy, and physical property evaluations were used to identify the mineralogy and assess their industrial potential. Samples were collected from a number of localities, namely Qasr El-Sagha (Fayum), Cairo-Alexandria Desert Road (Western Desert), and Qattamia area (Eastern Desert). This paper reviews the geological occurrence, the mineralogical and chemical characteristics, and the potential utilization of these deposits.

Jan 1, 1985

By W. D. Robertson, H. H. Uhlig

The intermetallic compounds MgzSn and Mg2Pb are two of the important series of stoichiometric compounds which magnesium forms with elements of the fourth group of the periodic system. Since there is a complete series of compounds, all possessing the same comparatively simple structure, a unique opportunity is presented to study their properties with respect to increasing atomic number of the anion as it varies from silicon and germanium, through tin and lead. The present work deals with the two lower members of this group, and it is hoped eventually that additional data regarding the silicide and germanide will be obtained. The results of such a complete study provide part of the essential basis for the empirical correlation and theoretical treatment which, in other systems, has contributed to an understanding of inter-metallic compounds and the metallic'state in general. Some experimental data are already available in the literature. However, they are fragmentary and limited in significance owing to the methods of preparation employed and the impure materials available at the time. It was our objective, therefore, using pure metals and improved metallurgical methods of preparation, to produce stoichiometric compounds of high purity for the study of their electrical and chemical properties. We felt that a detailed investigation of chemical properties, about which relatively little is known, combined with electrical properties, would be a significant contribution to the understanding of these compounds and in particular to the mechanism of corrosion associated with types of bonding in alloy systems. The chemical studies are reported elsewhere. Previous Investigations Previous work concerning the electrical properties of these compounds was undertaken in connection with the establishment of the two phase diagrams which are available in Hansenl and Beck. The first comprehensive investigation of the electrical conductivity of magnesium-tin and magnesium-lead alloys was made by Kurnakov and Stepanov.3 This was followed by Grube and Voss-kiihler4 who studied electrical conductivity and thermal expansion over a wide range of temperature and who, unlike Stepanov, appreciated the significance of the large solid solubility of tin in magnesium and took some precautions to obtain an equilibrium state. However, at the time these investigations were made, neither pure magnesium nor

Jan 1, 1949

By James F. McDivitt

The mineral industry of today is faced with a number of dilemmas, not the least of which grows out of the series of related facts-world mineral consumption is growing, and is expected to continue to grow; maintaining adequate capacity to meet needs will require very great capital investment over the next decades, investment which must be measured in billions of dollars; much of the new production must come from remote and relatively underdeveloped countries; many of the areas in which such development must take place are not areas in which private capital enters without some trepidation. There are real problems in financing new mineral development-problems which have occupied the thoughts of many in the industry. One group which is currently providing part of the answer, and perhaps pointing the way to further progress in the future, is the World Bank. Loans from the World Bank are arranged usually for countries which are attempting to develop their economies through expanded industrial production. More often than not they are for the development of electric power projects or transportation facilities. Although we consider the mineral industries to be basic factors in industrial development and very important factors in the early stages of development of a country, few of these loans are for mineral development-no more than a half dozen out of a total of well over 300 loans which have been granted to date. Yet the World Bank has played a far more important part in world mineral development than these figures would indicate. The few loans for mineral development which it has made are important, but of considerably greater importance are the secondary effects of many of the non-mineral development loans and some of the special services which the Bank also offers.

Jan 5, 1963

By Cornelius J. Dwyer

It is possible to hold a very optimistic view of the future of the U.S. coal industry, and there are those in the coal industry who generally choose to do so. For example, a major coal company stated recently in its annual report, "Coal's prospects appear brighter today than at any period in the past." In order to continue in this state of euphoria, it is only necessary to remind oneself of the following "facts":

Jan 7, 1967

By J. B. Austin

MEASUREMENTS of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage trans-formed on linear coordinates against time on either a linear or a logarith-mic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even inter-polation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valu-able when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decom-position of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

By Graham Bright

The rapid increase in reliability, the low cost of operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made. Forms Used in Hoisting Calculations Some of the hoist calculation methods are long and complicated. Where such calculations are seldom made, it is better to use the

Jan 1, 1922

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936

By F. V. Lenel

INTRODUCTION Two years ago in Chicago a seminar was held on the theory of sintering of pure metal powders As an introduction to this seminar Dr Rhines1 gave an excellent survey of the literature on this subject His method of presentation was to summarize the experimental observations on sintering and from them to develop a composite theory of sintering in which he combined all the important contributions to the theory into one organic whole In contrast to the mechanism of sintering of pure metal powders, which, of course, always takes place in the solid phase, sintering in the presence of a liquid phase, cannot be treated as one unified mechanism, such as the sintering mechanism of pure metals The reason is that there are really several mechanisms depending upon the type of alloy system which is sintered and the field of its constitutional diagram in which the sintering takes place Two mechanisms have been investigated and will be reviewed in this paper In the first mechanism the liquid is present during the entire time while the compacts are at the sintering temperature In other words they are sintered between the liquidus and the solidus of the alloy System and are heterogeneous during the entire sintering cycle The second mechanism applies to alloys in which the liquid phase is formed during the sintering process, but disappears before the sintering process is completed through diffusion and formation of a solid solution These alloys are therefore homogeneous at the end of the sintering cycle This second mechanism is more complicated because of the two stages of sintering, the liquid and the solid, as they may be called It is therefore not surprising that the few detailed investigations of sintering in the presence of a liquid phase have been concerned with heterogeneous sintered alloys, namely the tungsten-nickel-copper alloys, which is the so-called "heavy alloy," and the cemented carbides The mechanism of sintering of these systems is characterized by the fact that theoretical or near theoretical density is attained during sintering, while simultaneously a distinct grain growth takes place through solution of the smallest grains of the solid phase in the liquid phase and reprecipitation on the larger grains In the first part of the survey this sintering mechanism which is called for short the heavy alloy mechanism is treated in detail In the second part of the survey experimental observations for the sintering of homogeneous sintered alloys where the liquid phase disappears before the completion of sintering are discussed Much less systematic work has been done on these alloys to which the commercially important porous bronzes and the iron-nickel-aluminum permanent magnet alloys belong Emphasis will be laid throughout this survey upon the microstructural and density changes during sintering because the sintering mechanism can usually be described directly by these changes Other

Jan 1, 1948

By F. H. Willcox

In Bessemer-steel practice, air is blown through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and cafbon. Toward the end of the blow, when the iron is not protected from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Besserner and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast iron. is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blow holes lies in part in the presence of dissolved oxide of iron in the molten steel and its consequent reaction with the carbon of recarburizers, when these are added, to form gases. (Another factor in the origin of blow holes is, of course, the solubility of gases themselves in the steel and

Jan 1, 1917

By T. A. Read, S. W. Kitchen, H. I. Fusfeld

At the present time most artillery cartridge cases are used only a single time. Since the process of reshaping a fired cartridge case so that it may be used again is much simpler and cheaper than the original manufacture of the case, it is clear that important savings could be effected if such re-formed cases were used in place of new cases. Extensive use of reconditioned cases has been hindered in the past, however, by the deterioration of the brass which may occur in the period of time between the first firing and the reconditioning of the cartridge cases. This deterioration sometimes results in a dangerously high incidence of firing splits in groups of reconditioned cartridge cases. It appears that the mechanism of the deterioration is the season cracking of the brass, for season cracks, of varying degrees of severity, may frequently be found in the cartridge cases after their return from the field. There are, of course, severe practical limitations to the extent to which fired cartridge cases can be protected from corrosion under battle conditions, particularly since the powder residue in the case is itself corrosive. The present paper describes a rapid method of testing the sidewalls of artillery cartridge cases for the presence of season cracks. This method has been developed specifically for use in connection with the reconditioning of fired cases, and makes it possible to carry out 100 per cent inspection. This new method of inspecting cartridge

Jan 1, 1945

By David Mandolesi

An examination has been made of the structures of strand cast blooms and the rails rolled from them; this paper details the characteristics of these typical structures. Results of mechanical testing data show that this product compares with rails processed from conventional ingot steel. Improvement in processing yields and surface quality standards are also briefly discussed.

Jan 1, 1972

By J. D. Grozier, W. W. Mullins, H. W. Paxton

The morphology of the nucleation and growth of austenite into high-purity iron in NH3-H2, gas mixtzires has been studied. The growth rate of an austenitic rim (planar interface) from scratched surfaces of- polycrystalline iron specimens was determined as a function of temperature and percent NH3 and found to he in reasonahle agreement with growth-rate calculations based on a model which assumes the diffusion of nitrogen to he the rate-controlling step. Under certain conditions, austenite pew as platelets; growth rates of these along the surface of single crystals were found to he dependent on surface preparation, orientation, THE development of microstructures can conveniently be thought of in terms of nucleation and growth. The complex topic of nucleation in solid-solid transformations will not be discussed at length, although a few qualitative experiments were performed. Growth is determined by the mobility of the various possible interfaces under the available driving forces in a particular situation. In homophase transformations, it has been clearly demonstrated that the mobility is very sensitive to small amounts of impurities, to the kind of impurity, and to the orientation relations across the boundary.' A degree of quantitative knowledge has temperature and percent NH3. On electropolished surfaces with a (110) pole, the maximum growth rate of platelets was determined and found to be in agreement within a factor of 2 to 3 with theoretical calculations of the edgewise growth rate of a platelet. The calculations are based on a model which assumes that the diffusion of nitrogen in the ferrite in front of the moving curved attstenitic interface at the tip of the platelet is the rate-controlling step. The growth direction on the surface of the single crystal and resztlting habit plane of the platelets were determined and found not to he unique but to vary systematically with the pole of the surface. been obtained. In the case of heterophase transformations, which are significantly more complicated to treat, a comparison of theoretical and experimental studies often shows rather poor agreement.'-' The main purpose of the experiments discussed below was to obtain additional quantitative data on crystallographic effects on boundary mobility in a system which was otherwise as simple as possible, viz. the growth of iron-nitrogen austenite into fer-rite. In the course of the experiments, it became necessary to re-examine the theory for the growth of Widmanstatten plates, especially the influence of anisotropic interfacial free energy. Some other minor experiments in the Fe-N system were performed, and are described briefly. EXPERIMENTAL METHODS A) Material Preparation. The floating zone purified iron used for this investigation was supplied by Battelle Memorial Institute. The nominal composi-

Jan 1, 1965

By H. W. Graham

AS these annual occasions in honor of Henry Marion Howe continue through the years: there is progressively less likelihood that the lecturer will have had personal knowledge of Dr. Howe. The present speaker is one of those who unfortunately had no opportunity to come under the inspiring presence of this great metallurgist. A review of Howe's work shows it to cover a comprehensive range of interests and to evidence an impressive richness of detail. Not only was Howe at home in the laboratory, but he was familiar with the processes of iron and steel making and had a real understanding of them. His writings include much that is descriptive of processes with a wealth of material that is becoming of increasing historical value. He recorded his studies of the theoretical aspects of processes and published at least two process classifications, one in 1890 that was lengthy and somewhat theoretical, and a second in 1906 that was more of a practical listing. Wide as Howe's field of interest was, it is significant of the circumstances of his time that he gave- little consideration to raw materials or to their effect on iron and steel making processes. In 1933, Waterhouse, Howe lecturer for that year, presented a descriptive summary of the major steel making processes, and in 1946 Joseph discussed the blast furnace process. Otherwise Howe lectures have not dealt with processes as major subjects. In today's lecture, with no effort to describe the mechanical arrangements of iron and steel making facilities, it is proposed to examine the essential technological elements of the processes, to explore the inter-relation of these elements, and particularly to seek recognition and understanding of those factors which determine why certain processes are or are not used. The discussion of this lecture will deal with the major well-known large tonnage processes, with only such attention to processes of minor tonnage and special character as may be warranted for explanation by contrast. Subject to the errors of generalization and the shortcomings of condensation involved in presentation limited to a single hour, it is proposed to examine broadly but intensively those operations which convert raw materials into steel. It is an innovation for a Howe lecturer to discuss the raw materials of the iron and steel industry, but the changing circumstances of passing years intensify the influence of raw materials on processes and require the metallurgist to be alert for the process adjustments that may become advisable or mandatory. For a half century the metallurgical processing of iron and steel has followed a surprisingly straight path, but this does not necessarily mean that there are no curves in the road ahead. Ages ago primitive man came to know iron in its metallic form, not only by the

Jan 1, 1948