Search Documents

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

By Phillip O. Tyree, Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducing bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the pores of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also expanded reserves in a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore occurrences. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of June 1, 1984, a total of 29.87 million mt (29.4 million long tons) of sulphur had been produced west of the Pecos River. Duval Corporation has produced more than 88 percent of that total.

Jan 1, 1985

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as 'could be expected without railroad transportation

Jan 1, 1924

By AIME AIME

AT A meeting of the Iron and Steel Institute held in London on May 6, Dr. J. E. Stead was formally inducted into the chair by Dr. Eugene Schneider, the retiring president. After presenting the Bessemer gold medal to Harry Brearley, of Sheffield, England, for his distinguished services to the British steel industry, Doctor Stead delivered his presidential address, a masterly review of iron and steel making progress during the past 50 years, emphasizing economy in production, and pointing out suggestions for future improvement. A considerable portion of the address was devoted to blast-furnace operation.

Jan 1, 1920

By I. Fatt

Study of a model which contains "dead-end" pore volume indicates that pressure transients are influenced by the amount of dead-end pore volume and by the resistance of the flow path between the dead-end pore volume and the main flow channels. A semi-empirical method is demonstrated that makes possible measurenment of the volume in the dead-end pores and the total pore volume. The difference between these two volumes is the volume of the flow channels. An indication of the flow resistance between the dead-end pore space and the lain flow channels is also obtained. INTRODUCTION In some engineering calculations the distribution of pore volume in a petroleum reservoir need not be known. For example, a material balance calculation treats a reservoir as an oil-filled tank. In other calculations the distribution of pore volume appears implicitly through use of the porosity and the relative permeability and capillary pressure characteristics. It is the purpose of this paper to point out that under certain conditions the exact distribution of pore volume must be known in order to interpret correctly transient flow behavior. Pressure transients during single-phase flow in porous media are usually said to obey differential equations of the form

By W. S. Morris

THE East Texas oil field is the largest in the United States and perhaps the largest 'in the world ; likewise, it is one of the most interesting. The East Texas oil field is a water-drive field. Small amounts of salt water were produced from wells on the western side of the field from the bt-ginning of the development. By the end of 1933 (the field having been discovered in September 1930) water production had reached 9000 barrels per day. By the end of 1936, approximately 2000 wells were producing about 45,000 barrels of water per day, and the problem of salt water disposal attracted the serious attention of the operators. Salt water production in the field has steadily increased and today approximately 450,000 barrels of water per day is produced while the oil production averages about 375,000 barrels. The disposal of this salt water has therefore become one of the major operating problems. Various methods of salt water disposal have been tried in the East Texas field. Evaporation in open pits proved

Jan 1, 1944

By Charles A. Mitke

The Copper Queen mine is composed of seven divisions which are operated through the following shafts: The workings of the different shafts are connected by motor-haulage drifts on the even numbered levels. The general location of the ore-bodies and workings is illustrated by the vertical projection of orebodies of the district as shown in Fig. 1. The Uncle Sam, Southwest, and Czar workings have many connections to the surface through raises and extensive cracks that were caused by moving ground. These divisions are cool and are ventilated entirely by natural means. The Holbrook is ventilated partly by natural and partly by artificial ventilation, while the Spray, Gardner, Lowell, and Sacramento are ventilated entirely by mechanical means. In some of the divisions mentioned above a considerable quantity of air exhausts through shafts of adjoining properties.

Jan 1, 1916

By Alden B. Grenninger

The time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. Mosaic Structure For an exact definition of the mosaic structure of metal crystals—if, indeed, one can be found that will hold for all metals—one must await the results of much experimental work in this field. The writer's investigations have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.—Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few minutes to a few degrees3. Just as there are no exact dimension limits for macrograins, so the dimensions of a macromosaic vary considerably. Macromosaic structure may often be seen on copper single crystals if they are examined carefully with critical illumination4. However, back-

Jan 1, 1936

INTRODUCTION TO STATISTICAL INFERENCE The intent of the mineral appraiser in collecting samples from a mineral deposit is to arrive at accurate conclusions concerning the size and value of the deposit. In other words, he wants to derive reliable inferences about the total mineral population from the collected sample data, which (he hopes) is representative of the whole. The discussion of sampling theory in Chapter 2 was oriented toward assuring that our sampling techniques and sampling units would indeed be representative of the total mineral population. Chapter 3 described the most common statistical parameters for defining distribution in various populations. Chapter 4 gave some insight into theoretical distributions of random variables and the probabilities associated with them. The intent of this chapter is to derive inferences from the preceding information about the population mean and the population variance. Knowing something about the normal distribution, and assuming our samples represent a roughly normal population, we can make inferences or logical deductions about the estimated interval or the limits of values which can be assigned to a mineral population. ESTIMATION OF POPULATION PARAMETERS In the application of statistics to mineral deposits it is never possible to know the actual values of the parameters or the theoretical distribution of values within the deposit for which our data are samples. Even after the deposit has been mined out it is questionable if the true value of the parameters can be retrieved accurately, due to dilution, mining, and processing losses. Therefore, our problem is to determine what function of our sample values we should use to estimate the unknown parameters of greatest interest to us-namely, the population mean and the population variance of the deposit. Since we cannot know

Jan 1, 1980

By Francis M. Rich

BEFORE the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3: To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By A. W. Gauger

For perhaps one hundred years scientists have been engaged in attempts at devising a satisfactory method of classification of coal. During this time many charts, tables and graphs have been proposed, some of which have had considerable merit, but no one system has been found to be applicable to all ranks of coal, nor has any one system received general acceptance. In many of the proposals, water eliminated between room temperature and 105" C. has been regarded as extraneous matter and calculations have been made to the air-dry or water-free basis. Such methods of calculation do not lend themselves to satisfactory grouping of the high-moisture coals.1, 2 A consideration not only of the properties of the high-moisture coals and their behavior on drying but of the generally accepted ideas of the coalification process and the role of water in this process indicates that water is an essential constituent of all coals and therefore should not be neglected. For example, in such low-rank coals as the lignites of the Northern Great Plains' deposits the inherent moisture of the lignite as mined plays a very important part in the physical properties thereof. Freshly mined lignite contains upwards of 30 per cent water and is extremely tough and resistant to shock. Upon exposure to the atmosphere, the lump loses part of its moisture and checks and splits, leaving a friable and broken up residue. So far as we have been able to determine, water is the only thing lost in this process and we are forced to the conclusion that moisture plays an extremely important part in the structural properties of the original lignite. With reference to the coalification process, Mack and Hulett3 pointed out in 1917 the important part that water played therein. They observed that water cannot be removed from peat or coal by pressure alone, but only as the result of chemical reaction, and suggested that peat in its early stages may be largely a hydrosol. Slow chemical changes occur over a long period of time until finally the mass becomes more largely a hydrogel. These views are substantiated to some extent by the experi-

Jan 1, 1932

By G. L. Corrigan, J. R. Coleman

Four factors that largely determine the end product obtained when cement and water are mixed are the chemical compo ition of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the more finely ground a cement, and the greater the surface exposed in proportion to its mass, the more rapid is the hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.1 Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are poorer cementing materials than some of the more finely ground construction cements. On the other hand, often it is necessary to pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concerning the proper fineness range.

Jan 1, 1941

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By R. L. Wilcox, M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By F. W. Lake

The ultimate production from a natural reservoir of petroleum is inversely proportional to the gas-oil ratios existing during the producing life of the reservoir whenever gas is the major expulsive force in the recovery. In other words, in the period during which gas is the major expulsive force the ultimate production will be increased if the gas-oil ratio is decreased, and vice versa. This condition prevails in the greater number of the present producing districts. While this relation is difficult to prove from actual operation, on account of the present paucity of detailed observations, it must be admitted after a study of the forces and conditions governing the recovery of petroleum from natural reservoirs. Where gas and oil exist under pressure in sand interstices and water movement is not freely possible, the force expended in moving the oil to the well is the expansion and movement of the gas through the pressure differential existing between the interior of the reservoir and the well. If pressure and solution conditions in the untapped reservoir are such that the relation between gas and oil volumes at atmospheric conditions is as 100:1; and if during the producing period, until the gas is exhausted, the relation between the gas and oil volumes produced is 300:1, it follows that only one-third of the oil has been produced and the remaining two-thirds cannot be recovered unless some extraneous force is introduced into the reservoir. This serves to illustrate the importance of gas-oil ratio control during normal producing operations. Gas-oil Ratio Control Eliminating natural conditions in a reservoir, which govern gas-oil ratios, such as the physical properties of the oil and gas, the physical characteristics of the reservoir strata and the original pressure and solution conditions in the reservoir, which cannot be controlled by operation practice; and also eliminating operating conditions that apply to the reservoir as a whole, such as well spacing, well locations, relative completion dates, various penetrations and drilling practice; there remains but one condition in each well that influences the gas-oil ratio and that is

Jan 1, 1928

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By N. A. Richard, A. E. Austin, R. E. Maringer

AS part of a detailed study of the structure of metallic meteorites, the concentration and distribution of iron and nickel in the various phases of meteor -itic iron have been measured using an electron-probe microanalyzer. The specimen used was cut from a position about 3 in. below the surface of the Grant meteorite, a one-half-ton iron specimen (containing 9.35 pct Ni) found in New Mexico some years ago. A photomicrograph showing the general Widmanstztten structure, somewhat typical of iron meteorites, is shown in Fig. 1. The line across which the analyses were made is indicated by arrows. This area was chosen so as to evaluate the iron-nickel concentration in the three principal phases visible in Fig. 1. These phases, in the language of meteoritics, are kamacite, taenite, and plessite. Kamacite is the a-

Jan 1, 1960

By P. S. Rudman

The allotropic volume changes of the ,metallic elements are reviezoed with the conclusion that in general atomic volume is conserved to better than 1 pct in such transformations. A table of the atomic volumes of the metallic elements is given and its use in considering the size factor in alloys is discussed. The importance of the concept of atomic-size factor, due to Hume-Rothery and coworkers,' is firmly established. Most attempts at quantitative formulations of this concept have employed the atomic radius (half some interatomic distance) as the measure of size and innumerable tables of such radii exist. This is probably, however, an unfortunate choice of parameter. Firstly, discussion in terms of interatomic distances requires a knowledge of the crystal structure. While this is known, except for a few cases, for the elemental structures, there are still many undetermined alloy structures. Secondly, except for the simpler structures, face-centered cubic (Al),* body-centered cubic (A2),* and hexagonal-close-packed (A3).* with ideal axial ratio, there is no unique in- teratomic distance, an m y decision must be made as to which distance, or which average of the distances, should be used. However, the most important point is that for metals the dominant bonding parameter can generally be expected to be atomic volume and not interatomic distance. This is perhaps most explicitly stated in the Wigner-Seitz cellular method.' In this approximation, cellular polyhedra of atomic volume v are replaced by spheres of radius Y,: 4/3 ?rs3 = v. That is, there is no reference to the interatomic distances. If atomic volume is in fact the dominant parameter, then in allotropic transformations we might expect to find atomic volume approximately conserved. For example, in the A1 ? A2 transformation we would thus have

Jan 1, 1965

By H. H. Rachford

This work presents a first-order analysis of the instability underlying viscous fingering in adverse viscosity-ratio water floods. It extends previous analyses of frontal instabilities, which were carried out with equations for parallel plate models, by including effects of the saturation transition zone observed behind the front in water floods in water wet systems. This zone tends to insulate incipient fingers from the high-mobility watet;. thus conditions for the onset of fingering differ from those in the parallel plate theory. Finite-difference solutions of the two-dimensional equations of displacement in porous media exhibited the predicted stability characteristics in six hypothetical field- and laboratory-scale floods in rectangular reservoirs. In contrast to results with parallel plate systems, this paper concludes that for waterwet reservoirs, laboratory models scaled by the usual criteria are also correctly scaled for frontal instability. Further, fingering in the systems studied can occur in any saturation range behind the front, and may occur at an intermediate saturation even though stability obtains both at the saturation corresponding to the Buckley-Leverett front and near residual oil saturation. Other points of contrast are that the likelihood of occurrence of fingering may not increase as flow rate or viscosity difference increases, but my be sensitive to changes in he relative permealdlity and capillary pressure functions. INTRODUCTION The recovery of oil by water flooding frequently involves displacing the oil by water of a lower viscosity. Displacement of a fluid by a less viscous one may lead to gross channeling or fingering like that observed in solvent floods, in which it severely lowers recovery efficiency.1 In addition to adverse effects on recovery, it has been suggested that the unstable move- ment causing fingering may interfere with interpretation of scaled model studies of proposed water floods, since the instability in the model might not be faithfully scaled to that in the reservoir prototype. In view of the serious implications of this possible breakdown of widely used scaled model techniques4-6 it is the purpose of this paper to examine the question further. Instabilities in the solutions of systems of differential equations imply a loss of smooth dependence on initial and boundary conditions. Thus, the possibility exists that in using models whose scaling is based on the differential system there may arise size- and rate-dependent factors which are not properly scaled. This possibility was examined in detail by Chouke et al., who analyzed the instability of frontal advance in a related problem, water-oil displacement in parallel plate models,2 in which a moving interface separates two regions of constant, unequal mobilities. First-order perturbation theory predicts the existence of a critical wave length for the growth of perturbations: and a wave length of maximum instability of A, = The interpretation is that wave lengths in a perturbation which are longer than A, will grow. Thus, if the width of a two-dimensional channel is greater than A,, fingers will grow, and the spacing of the fingers which grow at the maximum rate will be approximately It is important that the higher the velocity and/or the difference in flow resistance, the lower is A,, and thus the greater the number of fingers that can grow in a given model. In applying these conclusions to porous media, a pseudo-interfacial tension, , was assumed for the invasion front. Since this would not necessarily be equal to the liquid-liquid interfacial tension, an unknown constant was substituted for the foregoing expression for A, This was determined

Jan 1, 1965