Search Documents

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By C. H. Herty

The results of a study of the open-hearth process from the physicochemical viewpoint are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. The effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styril from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900' F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,a Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 1, 1926

By Strathmore R. B. Cooke, William F. Stowasser

RESULTS presented in a previous paper1 have shown that the strength of fired pellets made from eastern Mesabi magnetite concentrates containing 8 to 9 pct Si02 as quartz and silicates is due to several processes which occur during firing. These are: l-recrystallization and cementation of the fragmented magnetite grains; 2-formation of slag from reaction between the quartz, silicates, and available ferrous iron, followed by slag-bonding of the magnetite grains; and 3-oxidation of the magnetite to hematite and subsequent recrystallization and grain growth of this constituent. Microscopic examination of all magnetite pellets fired in one operation in small and large-scale pilot plant furnaces and possessing normal strengths shows that the processes 1,2, and 3 have taken place; where strengths are low and the pellets are otherwise sub- normal, one or more of the processes has not occurred. For example, soft and friable red pellets may contain a central core of slag-bonded recrystallized magnetite which is strong enough in itself, but the shell contains only slightly recrystallized hematite, indicating that the maximum temperature reached was too low. Processes 1 and 2 can occur only under reducing conditions, as for example, when coal is intention- ally added to the original pellets; under neutral conditions, when pellets are fired in an inert atmosphere; or when pellets are brought so rapidly to temperature in an oxidizing atmosphere that oxygen diffusion to the core lags behind the recrystallization and slagging effects. This last-mentioned process has occurred in all pilot-plant shaft fur-

Jan 1, 1952

Jan 1, 1967

PRESENTATION of the 1922 Washington Award to Capt. Robert W. Hunt, honorary member and twice president of the Institute, was made at the annual dinner of the Western Society of Engineers, in Chicago, on June 18, 1923, in the presence of 250 mem-bers and guests. W. L. Abbott, Chairman of the Award Commission, when delivering the presentation address, said The life of the Govern-ment of this country, as the lives of governments are usually measured, is short, barely 150 years, but meas-ured by what it has accom-plished, this country has reached a venerable age. The first 75 years of our country's existence were necessarily preparatory to the greater developments which came in the second, and that last half of our country's existence is ex-ceeded, by ten years, by the span of life of our honored guest. "Very little iron and steel were produced in this coun-try until after the birth of Robert W. Hunt. And it was not until after 1860, when as a boy of 21 he joined his fortunes with those of the Cambria Iron Works, that the iron and steel business of the country really took root. After a year or two with the Cambria Works, he left a promising position to go into the army, where he served for four years. After the close of the war he returned to the iron works and qualified himself as a metallurgical chemist.

Jan 7, 1923

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

Jan 9, 1950

By L. C. Armstrong

Twice in the past two years and in two widely separated localities-one near Williamsville, Mo., and the other in the Allard Lake district of Quebec- the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately intergrown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely.

Jan 1, 1949

By H. S. Coe

ENGINEERS have long recognized the desirability of correlating the data obtained from small-scale slime-settling tests with commercial work as carried on in large tanks. This need, though most apparent in designing new installations, frequently arises also in existent plants, since a large range of experimental work can be performed without interfering with regular operation. GENERAL SETTLING PHENOMENA In order to develop rational methods of laboratory testing, it becomes necessary to study the general phenomena of settling. Since it was desired to give the public the benefit of these methods at as early a date as possible, together with the knowledge of the general principles of slime settling necessary for a clear understanding of the laboratory tests, we have ventured to discuss the subject in so far as brought out by the work which we now have under way. We realize that certain of our preliminary conclusions may be subject to modification, but it seems probable that, with but few exceptions, the general laws enunciated will cover the settling behavior of all pulps encountered in metallurgical plants. However, it must be recognized that there is still a vast amount of work to be done upon certain phases of the subject; therefore, at this time we will attempt only a discussion of the behavior of ore pulps during the process of settling or dewatering, under certain given conditions. The laws and principles controlling these conditions are not fully established, so that a complete discussion of them will not be attempted in this paper. In metallurgical practice, slime pulp consists of water, finely divided sand

Jan 3, 1916

By J. J. Kramer, W. A. Tiller, G. F. Bolling

The solidification of poly crystalline zone-refined lead has been examined. A novel casting technique was used, with several advantages such as unidirectional heat flow, atmosphere control, and decanting of the liquid during any stage of growth. The experimental results show the separate existence of two textures, a (111) surface texture at the chill surface and a texture in the columnar zone, in the absence of conditions which would produce dendritic growth. WALTON and chalmers have most recently shown that the dendrite direction is the preferred axial orientation for the solidification of many metals in casting. Experimentally, for aluminum and lead, they showed that in the columnar zone the dendrite direction, <l00>, predominated, developing from an equiaxed chill cast layer that exhibited no preferred orientation. A reasonable description of the way in which grains closer to the dendrite orientation were able to encompass other grains was then set forth. For their materials, it was also shown that high superheats could inhibit a preferred axial orientation from developing, presumably by inhibiting dendrite growth. The observations of Rosenberg and iller, on the other hand, showed that zone-refined lead, cast under conditions similar to those of Walton and halmers,&apos; had a definite <111> texture in the columnar zone. However, no examination was made of the chill surface to find out if the columnar zone texture was independent of the orientations at the surface. Since the existence of preferred growth in Upure" lead is thus in doubt, a reexamination of the casting of zone-refined lead is presented here, using a novel casting technique. EXPERIMENTAL PROCEDURES AND RESULTS Zone-refined lead was prepared from two starting materials;99.999+pct supplied by ASARCO, and 99.999pct supplied by COMINCO. The manner of zone-refining and the phenomenological tests for purity after refining, have been describedelsewhere.&apos; The casting apparatus is shown schematically in Fig. 1. The following general procedure was used: The metal was cut directly from the best parts of

Jan 1, 1963

By James Aston

Three years ago the writer presented a paper on the trend of development in the wrought iron industry,&apos; wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. M. Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences. In a history which extends to prehistoric time, and which is linked up with the earliest records of ferrous products, the dominant method of manufacture, as we have known it for little over a century, occupies a very small niche in the span of years that mark production and use of wrought iron. Puddling, the outstanding manufacturing method of

Jan 1, 1929

By John C. Smock

The fire-clays of New Jersey belong in two geological ages, the cretaceous and quaternary, or post-tertiary. Three very small deposits of plastic clays have been discovered within the limits of the Archæan rocks. These are not refractory and of little importance, excepting in a geological consideration. They have resulted from a decomposition of the feldspars of the rock in situ, and they have been classified as inferior kaolins.

Jan 1, 1879

By A. S. Dwight

Taking up first the lead field, flotation concentrates offer serious difficulties in handling and in preparing for the blast furnace, quite aside from the problems presented to the furnaceman by the necessity of smelting smaller tonnages of material higher in grade and usually basic in character, with the consequent changes in flux requirements and furnace operation. As received at the smelter, these concentrates are always wet and usually of the consistency of sticky mud. Difficult enough to handle in warm weather, they are worse in winter, when it may be necessary to blast them out of the cars. They hang up in bins and chutes and stick to conveyors, requiring the constant attention of the operators. If dried they become like wheat flour, involving heavy dust losses in handling and in furnace operations. Roasting in hearth furnaces is more difficult than with coarser materials. Dust losses are increased and, what is more serious, the moist concentrates tend to form balls or nodules, which harden and pass almost unaltered through the furnace with consequent high sulfur in the product, while the unballed fine particles lie on the hearth in a dense bed, practically impenetrable to the oxidizing gases, so that roasting takes place only on the surface of the bed. A more prolonged roasting period is therefore required and the capacity of a given furnace is decreased. They are entirely too fine to be charged into the blast furnace, even if thoroughly roasted; excessive flue-dust losses, irregular operation and slowing up of the furnace would be the obvious result. Consequently, it was early recognized that flotation concentrates would have to be put in coarser condition for smelting and the universal method adopted has been the Dwight & Lloyd process of sintering. This did not usually

Jan 1, 1928

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961

By D. A. Keyes

International Minerals & Chemical Corp. (Canada) Ltd. is presently exploiting by underground mining a potash-rich zone in the middle Devonian Prairie Evaporite formation near Esterhazy, Saskatchewan. Of the three main potash-bearing horizons denoted by Goudie as zones 1, 2 and 3 only the 1ower. two are present at Esterhazy and mining is confined to the lower or zone 1 horizon. The area in which the evaporites were deposited, although flanked on the west by a zone of geosynclinal deposition and tectonic activity, has been subjected to only very gentle epeirogenic activity. The sylvinite ore is coarsely crystalline and occurs in well-defined beds. The halite, sylvite and insoluble content of the ore bears a direct relationship to the lithological units, but the carnallite cuts across the beds. Local concentrations of salt produce blank spots in the ore horizon. Some of these appear to be salt-filled, post-ore channels and cracks while others have been formed by brines emanating upward from below the ore. INTRODUCTION International Minerals & Chemical Corporation (Canada) Ltd. is operating an underground potash mine near the town of Esterhazy in eastern Saskatchewan. The deposit was discovered by IMC in 1955. Subsequent drilling outlined extensive high-grade reserves, and in 1957 shaft sinking and plant construction began. Production from Yarbo No. 1 Shaft commenced in September, 1962 and quickly reached the initial capacity of one million tons of muriate product per year. Production is currently being expanded to 1.6 million tpy. The single mining level is 3140 ft below the surface at No. 1 Shaft. GENERAL GEOLOGY The Esterhazy district lies within the Interior Plains region of Canada and on the northeast rim of the Williston Basin (Fig. 1). Average dip of the rock formations in this area is about 40 ft per mile to the southwest. The potash ore occurs in the Prairie Evaporite formation of the Middle-Devonian Elk Point Group. The Prairie Evaporites are overlain by 3000 ft of Paleozoic shales and limestones and by Jurassic and Cretaceous sandstones and shales (Fig. 2).

Jan 1, 1967

By R. C. Hall

In the present work, experiments determined the effect of the order-disorder reaction near the Fe,Al composition on the magnetic anisotropy and magnetostriction of single crystals: A material which is more difficult to magnetize in one direction than in another is anisotropic, that is, the ease with which ferromagnetic materials may be magnetized in different crystallographic directions determines the anisotropy. Two investigators have estimated the anisotropy of the aluminum iron alloys from poly-crystalline data;1,2 however, these estimates should not be considered to be reliable. Siege1 made two accurate measurements of the first anisotropy constant* from single crystals of 4.0 wt pct aluminum sotropy throughout the ferromagnetic aluminum iron system have been described. These results were obtained from single crystals which were slowly cooled and, hence, ordered near the Fe3Al composition.4 Magnetostriction is the change in length per unit length resulting from applying a magnetic field to a ferromagnetic material. For the purpose of this report, the saturation magnetostriction was measured. This is the maximum change in length per unit length resulting from an applied magnetic field large enough to saturate the material in a given direction. This magnetostriction has been determined for single crystals of the ferromagnetic aluminum-iron system.&apos; The crystals near Fe3Al were also ordered. PREPARATION AND TREATMENT OF SINGLE CRYSTALS Single crystal bars were grown from the melt.&apos; The raw materials for these crystals were iron and aluminum of 99.9 and 99.99 pct purity, respectively. From the bars, crystals in the shape of circular

Jan 1, 1959

By James J. Scott, John J. Reed

In a year fraught with difficulties, especially to small operators, the more stable mining organizations have shown a dynamic readiness to plunge ahead in the development of new mines, new and ingenious equipment and new tools for management to take the guesswork out of important decisions. New Mining Equipment The mining equipment display at the American Mining Congress in San Francisco demonstrated some rather radical new design concepts and a new willingness to use imagination to come up with ingenious new applications and adaptations of standard equipment.

Jan 2, 1963

By M. Schmellenkamp

By comparing two longwall operations, one begun in 1956 and the other in 1960, the author is able to demonstrate the increases in production and performance made possible by longwall mining. These achievements have been brought about by continuous development of longwall mining equipment and associated roof supports. Because of this progress, longwall mining is able to provide, under proper conditions, high production per man-shift, remarkable cost savings, dependable roof control, safe working conditions and truly continuous production. It may seem odd that the title of this paper is not simply "Longwall Mining" but instead "Progress in Longwall Mining." However, the word "Progress" definitely has its place in longwall mining. If it had not been for progress in the development of longwall mining equipment and roof supports, the longwall mining method would not be able to compete in production and performance with modem coal mining machines. The longwall mining method was practiced at the beginning of the century and there were several successful operations in coal fields in Illinois. In those early days of longwall mining, the coal was undercut by hand 2 to 2.5 ft at the bottom of the seam and packwalls were built in the gob to support the roof. The roof eventually subsided and the weight of the subsiding roof was used to ride the face and break the undercut coal. Utilizing natural weight to soften the coal face is still practiced in modern longwall mining; however, the packwalling method has been replaced by the caving method and the roof is now supported by yielding steel roof supports and forepoling steel headers. The purpose of these yielding-type roof supports is to provide a safe working area for the crew along the entire longwall face, to permit continuous mechanical mining across the prop free face, and to provide a strong resistance for the roof by forming an even breaking line at the gob for the roof to cave. Roof supports and associated forepoling headers should be kept as close as possible to the face in order to prevent a caving between face and supports, especially under friable roof. This means that the coal should be extracted in small slices, allowing only a narrow roof area to be exposed and unsupported. The coal planer with its relatively high cutting velocity of 75 ft per min provides such an extraction of coal and has proved its high performance under difficult mining conditions. Since 1951, several longwall faces in southem West Virginia and Pennsylvania which have been equipped with the coal planer and friction-type manual roof supports have been successfully operated. Compared to today&apos;s longwall mining, these longwall faces required such a large crew, primarily to handle the roof supports, that the actual high production per shift was charged with too high a labor cost, thereby decreasing the tons per man. Yet, even then the longwall faces outperformed the conventional mining system under the same conditions. In order to demonstrate the progress that has been made in the development of longwall mining, a comparison will be made between a longwall face in Arkansas which was installed in 1956 and a modemized longwall face started in 1960 in southern West Virginia. LONGWALL MINING IN 1956 The 320-ft longwall face was developed in a 32-in. thick coal seam near Greenwood, Ark. The method of mining the 320-ft coal block was the advancing system in which three entries on either side of the face were driven ahead of the advancing longwall face. The face was equipped with a coal planer and a Panzer conveyor; timbering was done with wooden timbers and cribs. The roof supports were set without any pattern. The crew to operate the planer and to handle the roof supports (timbers and cribs) consisted of 15 men per shift. During a period of approximately eight monthsof single shift operating time, the average tonnage produced in this relatively low seam amounted to about 263 tons of clean coal per shift. To show the development in the coal plow from then until now, it should be pointed out that the standard plow was used in this operation. The plow was equipped with rigid bottom bits which could not be adjusted if the plow started to climb, thereby leaving bottom coal to be recovered by pick hammers end causing delays in production. The height of the plow

Jan 1, 1963

By J. M. Schopt

COAL petrology is the study of the lithologic composition and texture of coal and includes megascopic as well as microscopic differentiation. Coal petrography is a quantitative study, principally (but not exclusively) microscopical in nature. The distinction between coal petrologic and coal petro-graphic studies usually is not important, but it is important to recognize that these studies differ materially from other types of petrology that deal primarily with minerals. The petrologic entities* of coal are less clearly distinguished than most minerals and the basis of distinction is not always clearly expressed. The relation of coal petrology to geologic, mining, and technologic problems is most evident when results of coal petrologic studies can be stated quantitatively. The chemical and physical composition of coal and the determination of its quality and properties are continuing problems. The source of these problems lies in the heterogeneity of coal and in its almost complete insolubility in ordinary solvents at normal temperatures. The empirical and comparative character of standard chemical coal analytic values is one of the consequences resulting from heterogeneity and insolubility of coal. Nevertheless, these coal analytic methods are highly technical and diversified. Coal petrol.ogy employs a group of similar analytical methods which provide information about coal that the other methods cannot supply. The heterogeneity of coal is most clearly demonstrated by means of petrologic studies. The properties utilized in coal petrologic studies are related to texture (size, form, and association), hardness, light reflectance, and light absorption and transmission (color). Size relations are most evident but are commonly overlooked. Coal is classed chemically as a mixture, and chemical analyses thus show the composition of the sample as a whole. Geologically coal is an organic clastic deposit, derived from diverse plant fragments and particles having a size range comparable to that of a conglomerate or breccia. The mixture of different materials that compose coal, large and small, can be realized only by microscopic study. This is because the fundamental cellular units of plants, from which coal is formed, are microscopic in size. The kinds of altered plant particles and fragments in coal have specific differences in hardness, reflectance, and color that signify differences in composition. These differences must be taken into account in evaluating the aggregate properties of coal. Terminology and Texture Full discussion of terms applied by various petro-logists in analysis of coal is beyond the scope of this article. For convenience the simpler types of petrologic entities that are defined without reference to lithologic occurrence or texture will be called coal components. Fig. 1 lists reactive and relatively inert

Jan 1, 1957