Search Documents

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By R. D. Irving

THE object of the present paper is to give an outline account of the mineral resources of the State of Wisconsin, so far as they are now known, including both metallic ores and non-metallic useful mineral substances. The only previous publication making any attempt at such an account is one of a popular nature, prepared by the writer for Snyder and Van Vechten's Historical Atlas of Wisconsin, which was published at Milwaukee in 1878. The data upon which the statements of the following pages are based are chiefly from the

Jan 1, 1880

By W. A. Wood, W. H. Reimann

A study is made of the creep that can be induced in armco iron at room temperature by superposing small amplitudes of alternating torsion on a tensile creep load. It is shown that the creep differs from that in comparable tests on copper in being trmsient only. At the same time, though transient, the creep can produce extensions of some 10 pct under creep loads less than the tensile yield stress of the material. The creep can be largely suppressed b$ applying cyclic strain of suitable amplitude before applying the creep load and the metal thereby stabilized. At room temperature, plastic flow in a metal under steady load is normally limited by strain-hardening processes. However, if a small cyclic stress is superposed on the steady load these processes may be more or less neutralized and, as shown in recent investigations,'-4 plastic flow may continue. In this way annealed copper, for example, can be induced to creep continuously to fracture under loads as small as 1 tsi. Dislocation mechanisms possibly responsible for this room-temperature creep have been usefully reviewed by Feltner.But discussion so far has been based mainly on creep as it is found in close-packed metals initially in the annealed state, and their behavior may not be general. In fact, recent work shows that the form of creep in annealed copper is different from that even in cold-worked copper;7 the creep thus depends on the dislocation pattern already in a metal as well as on the metal itself. This paper describes the creep in annealed armco iron, tested in the same way as the above-mentioned copper. One object was to see how creep in a typical bcc metal compared with that in the annealed close-packed metals. Another object was to utilize the fact that a bcc metal like iron has a more pronounced elastic range than close-packed metals like copper and to find to what extent the creep load or superposed cyclic stress had to exceed their re-

Jan 1, 1964

By Georges Ranque

THIS paper by. Georges Ranque is an attempt to reason out the conditions of formation and stability of inclusions and to establish an operative process capable of eliminating or minimizing them. The paper consists of two parts; one in which the author considers the laws of physical chemistry and physics that apply to liquid slag-metal systems and one in which he describes a practice based on the theoretical considerations. Such a paper is bound to contain controversial points and it is therefore your speaker's intention to present Mr. Ranque's side of the picture to the best of his ability without regard for any thoughts or criticisms of his own. RISING VELOCITIES OF INCLUSIONS Most nonmetallic inclusions have densities ranging from about 1.7 to s, while liquid steel has a density of about 7. Under these conditions, ferrostatic pressure should cause the inclusions, being lighter, to rise from the bath and be eliminated. This rising tendency is expressed by Stokes' law, from which may be calculated the rising velocity of a spherical particle in a liquid medium whose density and viscosity are known.

Jan 1, 1947

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1916 to Mar. 10, 1916. ALLAN, FERGUS L., Min. Engr., Cons. Min. Engr., Mexico Mines of El Oro, El Oro, Mex. ARMSTRONG, EMERSON WARREN, Met.,. Mina Bibilonia, La Libertad, Nicaragua, C. A. BABB, P. A Blaisdell Coscotitlan Syndicate, Pachuca, Hgo., Mex. BANDY, PERCY J Fundicion Delicias, Calle Delicias, Mexico, D. F. BELLWALD, J. N Apartado 1488, Mexico, D. F. BILLICK, DON CARLOS, Min. Engr., Supt., Hess Gold Mines Co., Alturas, Modoc Co., Cal. BITLER, FRANK L., Cons. Min. Engr., Birkinbine Engineering Offices, Parkway Bldg., Broad and Cherry Sts.. Philadelphia. Pa.

Jan 4, 1916

By AIME AIME

AT the seventeenth National Metal Congress, held at Chicago, Oct. 1-3, the Iron and Steel Division and Institute of Metals Division participated with the American Society for Metals, American Welding Society, and the Wire Association in one of the most successful meetings ever held. The total attendance at the technical sessions and the scope of and interest shown in the exhibits at the Exposition were greater than at any of the "Metal Weeks" since the depression began. The Iron and Steel Division held two all-day symposia and one general session. The latter, at the International Amphitheatre, Wednesday afternoon, was the only one poorly attended. This was attributable, at least partly, to the location of the meeting roan.

Jan 1, 1935

By G. B. Walker

THE sink-float methods designated by heavy-media separation processes were pioneered by C. Erb Weunsch for the treatment of base metal ores as an improvement over jigs. The work of Weunsch was further developed by Victor Rakowsky and The American Zinc, Lead and Smelting Co. Early in the development of the processes, the inherent unsuitability of galena as the solid constituent of the medium was recognized and ferrous media amenable to magnetic recovery and control were developed. The high efficiency and low cost of magnetic recovery and cleaning of ferrous media regardless of particle size, slime contamination, or surfacial oxidation had led to the adoption of ferrous media by all of the sink-float plants operating under the heavy-media separation processes patents controlled by American Zinc, Lead and Smelting Co. Approximately 2,000,000 tons of base metal and nonmetallic minerals are treated each month by these methods.

Jan 1, 1949

By N. Mungan, J. L. Thompson

Laboratory displacement tests were performed to study oil recovery elficiency by gravity drainage in fractured systems under miscible conditions. The porous media used were cylindrical Berea and Blue Jacket sandstone cores containing a number of well-defined, artificially formed, vertical and subvertical fractures. Butane and Soltrol 130 were the two miscible fluids used. The purpose of the study was to examine the influences of the displacement rate, fracture density, fracture orientation, fracture permeability, matrix permeability, crossflow, core length and connate water on the oil recovery. It was found that displacement rate, matrix permeability and the subvertical fractures affected oil recovery most. The critical flow rate, based on the matrix permeability, was found to be a significant factor in the process. For displacement rates below the critical flow rate, the oil recovery efficiency appeared to be unaffected by the density of the subvertical fractures. At the high displacement rates, the fracture density becomes important, with the recovery being the most efficient in the core having the greatest number of the subvertical fractures. The magnitude of the fracture permeability, the fracture orientation, the core length and the connate water have little effect on the oil recovery efficiency. INTRODUCTION Gravity drainage under miscible conditions from relatively thick reservoirs can be a very efficient recovery process, especially at low flow rates where the gravity forces are dominant and, consequently, the adverse viscous fingers associated with the unfavorable viscosity ratio are minimized or eliminated. Such a process might involve injection of an LPG or some solvent bank at the crest and then driving the bank with dry gas. For some favorable combination of reservoir temperature, pressure and oil composition, there may be no need to inject any solvent bank, since enrichment of the dry gas by the light ends of the crude creates an in-situ solvent bank. Slobod and Howlett2 have studied the effects of gravity segregation in vertical unconsolidated porous media under miscible conditions in the laboratory. The main variables in their study were the viscosity ratio, the density differences and the rate of flow. In this study, the objective was to find the influence of fractures on gravity drainage under miscible conditions. A greater number of related variables were also studied. LABORATORY STUDY CORE DESCRIPTION Displacement tests were performed mostly in cylindrical Berea sandstone cores. In a few cases in which a much lower matrix permeability was desired, Blue Jacket sandstone cores were used. The vertical fractures were formed by cutting the cores with a thin circular blade or by parting them along a bedding plane. The vertical fracture plane always contained the axis of the cylindrical core. The subvertical fractures, cut with a saw, were inclined 45' from the horizontal. The line of intersection between the planes of the vertical and subvertical fractures was parallel to the circular faces of the cores in all cases except one, as depicted by VF3HF-2 in Fig. 1. Fracture geometry of the other cores is also given in Fig. 1. Tables 1 and 2 give the physical properties of the solid and fractured cores, respectively. The suffixes and prefixes shown for each core have been used throughout the paper so that the reader may discern the fracture geometry from the core numbers.

Jan 1, 1970

By Paul A. Bailly

2.1-1. The Exploration Function in the Mineral Industry. With regard to a new mine, exploration can be technologically defined as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet, and annual output of the new extractive operation based on a certain mineral deposit. The activities that follow such a decision are called first development, then operation (90). Thus, in the U.S.A., exploration may continue in the technological sense after a mineral property has entered the "development stage" as defined for tax purposes. Regulations under Sections 1.615.1 and 1.616.1 of the U.S. Internal Revenue Code state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer" (95). There are, of course, many instances where additional later exploration discloses additional reserves which justify a plant much larger, more efficient and more profitable than the minimum feasible commercial operation. After a surface mine is put into operation, additional search generally will increase the reserves and thus warrant expansion of the rate of output and/or extend the life of the operation. The methods and techniques in such search are similar to those used in predevelopment exploration. This activity has produced a major part of new reserves for all mineral commodities but is not considered as exploration in the context of this chapter. The objective of exploration is, briefly stated, to find and acquire a maximum number of new economic mineral deposits with a minimum cost and in minimum time. The search must be so organized as to maximize the overall probability of discovering commercial mineral concentrations within a minimum time with the funds available. As shown by Celasun (27) these statements are neither adequate nor complete from a pragmatic point of view. Each actual exploration venture must define its objectives in terms of a minimum rate of return on investment for any deposit found

Jan 1, 1968

By Nelson Severinghaus

Crushed stone leads all industrial mineral, except cement in annual value of production in the United States. It is also interesting to note that crushed stone value is exceeded only by that of fuels, cement, and iron ore among all mineral products of this country. An industry which started with hand-sledging to produce smaller sizes of broken stone for hard surfaced improvement of roadways as designed by McAdam in England about 1815 has grown into a complex industrial giant. Most of this growth started with the invention of a mechanical rock crusher just under one hundred years age (1858) by Eli Whitney Blake. This invention made possible the production of greater tonnages of smaller sizes of broken stone and greatly accelerated its use for Macadam road pavements and for railroad ballast. Stones Used for Crushing All three of the major geologic classifications of stone, sedimentary, igneous, and metamorphic, are widely used in the production of crushed stone. Satisfactory physical and chemical properties can be found in each type so that economic availability becomes the prime determinant for development. Table 1 lists more common rocks of the three main groups with average values of specific gravity and toughness as measured by Deval test. This widely used classification was suggested by C. E. Lord, of U. S. Bureau of Public Roads. The physical properties were compiled by D. O. Woolf in "The Results of Physical Tests of Road Building Rock," U. S. Department of Agriculture, Bulletin 76. It should be noted that the figures given in Table 1 are averages. Very substantial variations in the physical properties of rocks within any one classification will occur. The solid surface of the earth was first made up of igneous rocks resulting from the solidification or crystallization of molten material upon cooling. These igneous rocks were disintegrated into sand, clay, and gravel by the weathering action of wind, water, chemicals, [ ] and temperature changes. The products of weathering were transported by wind and streams until they reached less turbulent areas such as oceans or lakes and were deposited. Chemical deposition between grains of sand or clay or the physical action of pressure and heat then solidified them into sedimentary rocks

Jan 1, 1960

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By L. W. McKeehan

The occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.' This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. Method of Preparation The material in which the crystals here dealt with were grown was made from 1/8in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400" C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. Measurements The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, 8, from one direction of the wire axis, and an azimuth or longitude, ?, from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

By A. A. Rauth

In this paper, the author derives a series of formulas from basic principles and illustrates the application of these formulas to practical grinding charge problems. The paper establishes the nearly proportional relationship of mill power to charge level and shows how this relationship can be used to advantage in the design, manufacture and operation of grinding mills. The procedures outlined offer a rapid means of anticipating the power requirements for a given charge or determining makeup charges for a given power reading. The theories which have been developed concerning the dynamics of grinding have been motivated largely by the desire to derive workable formulas for the accurate determination of grinding mill power. This accurate determination has always been handicapped by the large number of variables to be considered, some of which are mill diameter, length, speed, liner design, grinding charge and material density, volumetric mill loading, internal friction, and charge size and gradation. In efforts to determine mill power, attempts have been made to utilize torque concepts. The formulas derived consider the grinding mass as a rigid body and utilize factors that are based on empirical data so that the movement of the charge within the mill is compensated for. These formulas are of principal interest to the mill designer since he is charged with the responsibility of analyzing all of the variables and from them predicting a mill size and a motor size which are compatible both with each other and with the grinding job for which they were intended. The mill operator, on the other hand, has an entirely different problem. The mill dimensions are already established and so is the driving motor. The operator's main concern is to obtain maximum performance from the mill he already has. For him, the many variables which perplex the mill designer are fixed values. Mill diameter, length and speed are set and, to a large extent, so are the conditions inside the mill from which the torque formula advocates derive their empirical data. It is conceivable that if the major mill dimensions which affect power demand are held constant, and if the variables influencing empirical factors are held fairly constant, as they are in an operating mill, then the only major variable remaining which affects power is the level of the charge itself. Under this condition.

Jan 1, 1970

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By Om P. Pande, Larry S. Diaz

Modern mineral processing plants could not operate efficiently, or even exist, without instruments which indicate, record, control, and in some cases anticipate the many changes that occur in a process. Even in plants which are operated manually, instruments are used to tell the operator when he should turn a valve or press a handswitch. Accordingly, all mineral processing plant engineering and construction projects must give careful consideration to this area of design activity.

Jan 1, 1978

Jan 12, 1951

Jan 1, 1957

By M. Van Weyenbergh, G. Van Esbroeck

THE copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment,, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Miniére du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. PRINCE LEOPOLD MINE The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60ºto a depth of 300 ft., and more uniformly 80º below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein-the footwall-is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1939

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10 to May 10, 1914: Members ADAMS, HENRY H., JR., Merchant, Henry H. Adams & Co., and Colonial Iron Co., 149 Broadway, New York, N.Y. ADAMS, LELAND D., Mine Mgr., Supt., East Canada Smelting Co.,Weedon, Quebec, Canada. AGUILERA, EUGENIO, Chief Engr. Mining & Foresting Dept. of Santiago, Santiago de Cuba, Cuba. ALFORD, NEWELL GILDER; Min. Engr., Asst. Chief Engr., St. Bernard Mining Co,. Earlington, KY.

Jan 6, 1914

By William G. Brissenden

Gaspe Copper Mines Ltd., a subsidiary of Noranda Mines Ltd., operates a completely integrated copper mining, milling and smelting plant at Murdochville, on the Gaspe Peninsula of Quebec. Operating six days a week, the mine produces 8000 tpd of ore. The mill runs continuously and capacity is rated at 6500 tpd of ore. Treating Gaspe concentrate output plus a certain amount of custom concentrate, the smelter produces between 3700 and 4000 tons of copper anodes per month.

Jan 9, 1959