Search Documents

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-''FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By A. L. Blomfield

THE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulpho-tellurides, with practically no base metals such as Pb, Cu, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. CLASSIFICATION OF ORES For efficiency, it has been found advisable to separate the ores into two classes according to their line content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the line, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A Class B Insol 56.70 75.90 Al203 2.30 3.40 Fe 3.26 3.48 CaO 1.57 5.12 S 1.79 1.80 Mg0 0.21 1.08 Ignition loss 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 percent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 8, 1918

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By Martin G. Castro, Renato G. Bautista, Morton Smutz

During the last 25 years, multistage mixer-settlers have been used extensively for liquid ion exchange work. The mixer-settler has the advantage of being a compact device in which a large number of stages can be assembled in a relatively small area. They are particularly advantageous for the separation of rare earths. Most of the adjacent rare earths have separation factors which are near one, which means that a large number of stages are needed to produce a good separation. When two elements (m, n) are extracted simultaneously, the separation factor (ßm, n) is defined as: [ ] where Ym, Yn are the molarities of the respective elements in the organic phase and Xm, Xn, are their molarities in the aqueous phase at equilibrium. The industrial consumption of rare earth oxides rose to over 6800 tons in 1968, an increase of 33% over 1967.1 The increased production and demand for rare earth and lanthanum chlorides for petroleum cracking catalysts was one of the principal factors in this increased consumption of rare earths. In 1968 approximately 59% of the rare earth oxides produced were used for gasoline cracking catalysts in the form of rare earth and lanthanum chlorides. There was also an increase in the sales of lanthanum oxides for use in optical lenses and in fiber optics. The future looks good for the rare earth industry. The rare earths can be expected to be used in many new products which are being developed. Until the late 1950's tributyl phosphate (TBP) was the principal solvent used in rare earth liquid ion exchange. In 1957 Peppard3 reported the use of di (2-ethyl-hexyl) phosphoric acid (D2EHPA) as a solvent for separating the rare earths. Rare earth separation factors of up to 2.5 were obtained in nitrate and chloride systems while the maximum separation factor using the

Jan 1, 1972

By W. D. Potter, E. T. Peters

Single-crystal films of boron have been prepared by thermal reduction of purified BCl3 with subsequent deposition of boron onto oriented silicon substrates. The structural properties of films prepared under various experimental conditions have been determined by light microscopy and "grazing-" angle electron-diffraction analysis. An orientation relationship is proposed for silicon and a-rhombo-heclral boron which can be described as: (111)Si (112)B; [110]Si [110]B ElEMENTAL boron is known to have a high energy gap* and consequently has potential value as a high- *Energy gaps of 1.35 to 1.55 ev1-3 and 2.0 ev4 are reported for ß-rhombohedra1 and a-rhombohedra1 boron, respectively. temperature semiconductor.5 Exploitation of this property, however, has been hampered by the unavailability of pure, single-crystal boron. Two recent symposia6,7 have treated the subjects of purification, crystallization, crystal structure, and properties of boron and provide a foundation for further investigation in these areas. The structure, lattice constants, and observed ranges of stability for four reported polymorphs of boron8°12 are listed in Table I. The rhombohedral structures are generally accepted as true polymorphs whereas the tetragonal structures are believed to be transient. Most currently available single crystals of boron are grown by Czochralski and floating-zone methods. Unfortunately, these crystals generally contain numerous defects and are highly strained as a result of the polymorphic transformations and thermal contractions which accompany cooling. Recently, Armington, Potter, and Tanner13 have reported the formation of single-crystal films of boron on silicon single-crystal substrates through thermal reduction of BC13 by hydrogen. Boron E. T. PETERS, Junior Member AIME, is Senior Scientist, ManLabs, Inc., Cambridge, Mass., and W. D. POTTER is Research Chemist, Air Force Cambridge Research Loboratories, L. G. Hanscom Field, Bedford, Mass. formed at temperatures near 1000°C was identified as the a-rhombohedra1 form, consistent with expectation. The present paper describes a continuation of this work with specific reference to characterization of the structural features of the deposited boron films. The ultimate goal of this program is to produce large-area single-crystal films of a-rhombohedra1 boron to be used for electrical and optical studies by other workers. PREPARATION OF BORON FILMS The experimental procedure of preparing thin films is similar to that described by Theuerer14 for the epitaxial growth of silicon by thermal reduction of SiC14 and has already been described as applied to the preparation of boron thin films.13 Briefly, a mixture of BCl3 vapor and dry hydrogen is passed over a heated silicon substrate. Thermal reduction of the BC13 allows deposition of boron on the substrate. The substrates were {111}-oriented, single-crystal silicon. Square specimens 0.63 cm on an edge by 0.1 to 3.0 mm thickness were prepared by

Jan 1, 1965

By C. C. McDermond, Others, B. N. Zavoico

Production of crude oil in Venezuela for the year 1937 was 186,653,-916 bbl., as compared with 155,228,982 bbl. produced in 1936, an increase of almost 31,500,000 bbl. The oil-field strike, which started on Dec. 14, 1936, lasted until Jan. 25, 1937, when a total of 10,000,000 bbl. of production was estimated to have been lost (5,750,000 bbl. in 1936 and the remainder in 1937). Of the total of 186,653,916 bbl. produced in 1937, the Lagunillas field contributed 45.6 per cent, a drop of approximately 10 per cent under 1936 figures; Tia Juana, 14.3 per cent; Quiriquire field, 14.0 per cent; La Rosa area, 13.3 per cent and the Mene Grande field, 7.6 per cent, these being the five leading contributors of the year's production. Detailed production figures by fields and by companies are shown on Table 1. Of the total production of Venezuela the following four major companies accounted for the greater proportion: Standard of Venezuela and Lago Petroleum Corporation together, 48.3 per cent; Shell, 37.4 per cent and Venezuela Gulf, 14.0 per cent. At the end of the year, 2491 wells were producing, of which number 1291 wells were pumpers, or about 52 per cent. Production The accompanying statistics of production record of Venezuela oil fields from its inception to Dec. 31, 1937, shown on Table 2, indicates that the cumulative production reached 1,503,283,228 bbl. In order of importance, Lagunillas leads all the fields, having accounted for about 50 per cent of Venezuelan production, followed by La Rosa area, which produced about 21 per cent; Mene Grande, which produced about 13 per cent, and Quiriquire, which produced 6.5 per cent. Table 3 shows the age of each field. Mene Grande is the oldest, having produced for 24 years; Tarra is next, 21 1/2 years old, and El Mene third, 171/2 years. The gravity of the crude from the various fields, also shown on Table 3, remained unchanged, the only addition being the new Tia Juana field, which averages 15.6' A.P.I. Table 4 shows the method of production by fields as of Jan. 1, 1938; at the end of the year 2491 wells were producing, compared with 2005 wells producing at the beginning of 1937, or an increase of 486 wells. The completions for the year reached 512. Of the 2491 wells producing crude oil, 1291 wells, or approximately 52 per cent, were pumping, 925 (approximately 37 per cent) were flowing naturally and 275 (11 per cent) were on

Jan 1, 1938

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

Southern California Academy of Sciences, Los Angeles Museum, Exposition Park, Los Angeles, Calif Howard R Hill, Secretary. The Academy has published one book which should have mention: Southern California geology and Los Angeles earthquakes, by R T. Hill (1928) Price, $5.

Jan 1, 1933

By Louis A. Carapella, William E. Shaw

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By William E. Shaw, Louis A. Carapella

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

Q: It is May 1961 at Bill Wrather's Washington house. Bill, think back to your first job after college. Wrather: Perhaps I ought to go back a little bit further than my first job. I entered the University of Chicago with the idea of studying law. My intention was to take a 4-yr liberal arts course and superimpose a law degree on that. But during my undergraduate work I fell under the influence of R. D. Salsbury. He decided I had some talent as a geologist and influenced me to take a geological course. Nevertheless, I did not give up the idea of law. While in school I took a spell of typhoid fever and almost died. The doctor recommended outdoor exercise, so a geological job seemed logical. W. H. Emmons was a graduate student in the University and he interceded with Dr. Hayes of the USGS. I went on the payroll as assistant packer at $60 a month. I had one of the most glorious summers I ever spent in my life. That fall and the following year I took law courses and became thoroughly convinced that I was cut out for a geologist rather than a lawyer. I finished up my law work in 1908 while waiting for a job with Bill Emmons, who was doing a careful study of Goldfield and Tonopah.

Jan 4, 1964

By Rudolph G. Wuerker

THE Krupp-Renn Process,[1] has been successfully used to treat low-grade iron ores, laterites, titaniferous sands, and other minerals, and before World War I1 25 units were built by the Krupp-Grusonwerk, Magdeburg, Germany. J. J. Howard[2] has shown theoretical advantages of the pyro-metallurgical treatment over conventional approaches; and the process was described by R. Durrer[3].

Jan 1, 1951

By M. J. Mullikin, J. B. Conway

for use in describing combined first- and second-stage creep data. In the above ?o represents the instantaneous strain on loading, ?t the limit of transient creep, ?S the steady-state creep rate, t the time, and ? a constant leading to the exhaustion rate of transient creep. It was noted that this equation was similar in form to that proposed originally2 by McVetty. This type of equation was also suggested by Andrade and Aboav3 in studies of the shear strain of cadmium. Calculation of the constants ?o, ?t, ?, and ?s, in Eq. [ l] is somewhat involved due to the slight complexity of this relationship. In the paper by Garofalo a computer approach based on a least-squares analysis was recommended. Such an approach involves a trial and error solution but when a computer facility is available the difficulties in this calculation are of little consequence. It does mean however that the evaluation of this type of equation would become quite tedious if computer facilities were not available. Some recent studies have identified a fairly straightforward method for calculating the constants in the Garofalo equation. While not leading to a least-squares evaluation the approach is accurate and is recom-

Jan 1, 1967

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

By AIME AIME

CONVENTION plans for the A.I.M.E. Regional Meeting to be held on the Minnesota Iron Range Aug. 12 to 1.5 are being completed to give the visiting member?s from all parts of the country a wide variety of technical and recreational features. High spots of the social events are the official dinner, dance, luncheon and golf: and of course, special provision is being, made for the entertainment of visiting ladies. The technical sessions will fit in with scheduled trips to view all phases of mining, beneficiation and transportation of iron ore. Men from the West and Southwest will find much of interest in the detail of the mining operations. A trip to the steel plant of the

Jan 1, 1941

By G. S. Hume

RECENT developments in the Turner Valley gas and oil field, 40 mi. southwest of Calgary, Alberta, have indicated a large producing crude-oil area. Drilling be¬gan in Turner Valley in 1913 but no major developments took place until the fall of 1924, when Royalite No. 4 well at a depth of 3740 ft. in the upper part of the Paleozoic (Mississippian) limestone obtained a production - of 20,000 M cu. ft. of gas with a content of about one imperial gallon of naphtha (73° A.P.I.) per M cu. ft. This well produced as much as 600 bbl. of naphtha per day, and until abandonment in 1934 produced 911,313 bbl., which together with the gas sold was valued at about $5,000.000.

Jan 1, 1937

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

By I. E. Rosenzweig

The problem considered in this paper is as follows: An arbitrary horizontally stratified area is given. The electrical properties of this area are characterized by a function p(z) (Fig. I), which shows the relationship between resistivity p of the soil and the depth z. For such general case the apparent resistivity p* will be computed, by earth-resistivity measurements carried out by any given configuration of electrodes. General solutions of this problem appear to be very important for interpretation of field results of resistivity measurements, concerning structural investigations. Such solutions have been given by many authors for the special case of a finite number of homogeneous layers (Fig. 2)lV4 as well as for the more general case of continuously ranging resistivities.5-8

Jan 1, 1940