Search Documents

By B. L. Averbach, M. Cohen

THE PROBLEM MANY hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or subatmospheric cooling.1,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1948

By A. M. Talbot, John T. Norton

TheRe is still considerable controversy as to the exact nature of the mechanism of the age-hardening process, in spite of the many experiments already performed. For this reason, a considerable number of typical systems should be examined in detail and their results correlated. Furthermore, the methods of studying the changes that take place during the progress of this phenomenon should be carefully scrutinized and the different methods applied to the same samples, preferably at the same time. The experiments described in this paper are presented to supply information on one age-hardening system and to show how the various methods of investigation compare in their indication of what has happened. In brief, the progress of aging in magnesium alloys containing about 10 per cent by weight of aluminum at different temperatures was followed by measurements of hardness, electrical resistivity, dilation and lattice parameter, and by microscopic observation. Previous Work Meissnerl,$ Archer?, and Gann3 have investigated the changes in mechanical properties of magnesium-aluminum alloys during aging and have shown the optimum condition for the age-hardening treatment. Meissner's results are particularly interesting because when replotted so that they represent hardness as a function of aging time, the curves of 125" and 150" C. show two hardness peaks. This result was not confirmed in the present work. Schmid and Siebe14 have reported an investigation that is similar to the present one but it was not published until the present work had

Jan 1, 1936

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By W. T. Read, W. Shockley

THE subject of this chapter is the application of the dislocation theory to two problems of physical metallurgy where the theory has been able to give definite predictions that subsequently have been verified by experimental observations. Much of the history of dislocation theory has consisted of the explanation of already established results on the basis of ad hoc assumptions. Scattered bits of fundamental theory were formulated as needed-in particular explanations. The result had the appearance of a hodgepodge of ingenious ideas and exciting but possibly artificial speculations. The review article by Koehler and Seitz in this volume gives an excellent picture of the breadth, diversity, and flexibility that have made dislocation theory attractive to speculative theorists, although occasionally bewildering to others. Since 1950, there have been two developments, which have helped to establish dislocation theory, on the one hand, as a systematic coherent body of theory and, on the other, as a means of making predictions that can be tested experimentally and thereby guide experiment into more fruitful channels. The first and easier of these developments has been the systematic derivation of the classes and properties of dislocations from fundamental crystallographic concepts. An example of one phase of this development is the rigorous treatment of

Jan 1, 1954

By J. S. Lasater

Resu1ts of experinmental measurernents of heat capacities and thermal conductivities of some typical porous rocks are presented. Measured heat capacities agree closely with va1ues calculated front known chenlical . compositions of the rocks. On the basis of this agreement, heat capacitir.7 of fluid-satttrated rocks were calc~ililted. Therrnal conductivities of the rock samples were measured under varioits conditions of fluid saturation. From these data therrnal dif-fvsivities were calculated. A significant variation of thermal diflusivity with trnlperature is indicated. Knowledge of the thermal characteristics of fluid-bearing porous rocks has become increasingly important with the development of thermal oil-recovery processes. Reliable thermal data for petroleum reservoir rocks are not available and approximate values are generally assumed for reservoir calculations. 'The effects of temperature, pressure and fluid saturation on thermal properties of porous rocks have not been carefully studied. The purpose of the present work was to measure and report the thermal characteristics of some typical porous rocks. A group of eight sedimentary rock samples, including limestone, shale, sandstone and silt-stone, was selected for the study. Properties reported include heat capacities, thermal conductivities and thermal diffusivities. The effect of fluid saturation on these properties was also considered. Determinations of thermal properties require precise measurements which are time consuming and difficult to reduce to a routine basis. Methods have not been developed for measurement of thermal proper-ties under conditions of pressure, temperature, and fluid saturation, which may be encountered in thermal recovery processes. As one approach to these problems, some preliminary work on methods of estimating thermal properties from other more readily measurable characteristics of the rock-fluid system is reported. The samples selected for the studies were oilfield cores from within, or closely associated with oil-productive zones. Descriptions of individual samples are given in Table 1. Clay minerals present in the samples were determined by differential thermal analysis (DTA). Quartz content was estimated from DTA cooling curves. For all but the thermal conductivity tests, a representative 200-gm sample of each core was disaggregated, thoroughly extracted in diox-ane and oven dried at 100°C. The cleaned and dried sample was care- fully split into appropriate portions for the several tests. Chemical analyses of the samples were obtained to permit calculations of heat capacities by methods which are outlined later. Resuits of chenlical analyses are given in Table 2. Heat contents of the test samples were measured by a Runsen-type calorimeter. The heat content of the unknown sample is measured relative to the known heat content of platinum. The apparatus is referred to as a relative error type because of the comparative measurements, and has the advantage of canceling systematic errors. Experimental results are reproducible within 0.5 per cent. A temperature base of 298.16 K is taken for heat content measurements. Measurements were made at five temperatures (260, 440, 620, 800 and 980° F). It was necessary to preheal the sample above the maximum experimental temperature to eliminate volatile constituents. Assuming the weight loss on pre-heat, ing was mostly water, a correction to the observed heat content was made to account for the water originally present in the sample. This latter procedure was followed in the determination of calculated heat contents as will be described later. The apparatus and the method of measure-

By John B. Myers

Vermiculite is the commercial name used to describe a micaceous mineral that expands appreciably when heated. This process, called exfoliation, results in a light weight material. The light weight material is also called vermiculite, or more exactly, expanded vermiculite. Practically all uses of vermiculite are for the expanded material. Composition and Properties Vermiculite, in its natural state, has the characteristic micaceous habit and a perfect basal cleavage and readily splits into thin laminae, which are soft, pliable, and inelastic. The monoclinic crystal faces are often marked by triangular lines at 60° and 120°. The hardness varies from 1.5 to 2 or more, depending on the composition. The specific gravity varies from 2.2 to 2.7; specific heat 0.2; fusion temperature 2,000° to 2,500°F; luster pearly to greasy; color amber, bronze, brown, dark green, and black. Feel is like talc and sometimes soapy when wet. When heated quickly at elevated temperatures, vermiculite exfoliates by expanding at right angles to the cleavage into long wormlike pieces (the name vermiculite is from the Latin vermiculari, to breed worms). This important characteristic of expansion is believed to be a mechanical separation of the layers when the contained water is converted to steam. The increase in bulk volume of commercially prepared material is 8 to 12 times, but individual flakes may expand as much as 30 times. There is no expansion parallel to the cleavage. Vermiculite may also be expanded by several chemical processes such as soaking in hydrogen peroxide, weak acids and other electrolytes. The color changes during expansion. Heat-treated material changes to a light golden bronze or cream color depending on composition. The conditions of heating affect color. Heating in an oxidizing atmosphere produces reddish colors and heating in a reducing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. Vermiculite is hydrated magnesium-aluminum silicate. Although there has been much research on the chemical and structural composition, there is not yet complete agreement on the exact formula and composition. This is to be expected since vermiculite is not a mineral of fixed composition and different workers have examined different varieties. It has been proposed that vermiculite is not a single species but a family of related minerals. This has also resulted in many names for the particular vermiculite found in a certain deposit. All of this difficulty arises from the very nature of its crystal chemistry. Unlike most minerals, certain crystal structure properties and the chemical composition can be changed by the ordinary forces of nature or in the laboratory. This would suggest that vermiculite be thought of more as a variable mineral rather than a group of related species. It was stated on page 261 of this volume in the chapter on Clay Minerals by H. H. Murray of the Georgia Clay Co., that vermiculite is an equidimensional, expandable clay mineral. Gruner (ref. 14, Chap. 12) showed that the structure consists of a layer made up of two silica tetrahedral sheets with a central magnesium, iron octahedral sheet separated by two layers of water molecules and adsorbed magnesium and calcium ions. Mathieson and Walker,2a in a recent publication, agree that vermiculite must be regarded as a true clay mineral. The characteristic properties of the mineral, such as high cation ex-

Jan 1, 1960

By George H. Gilman

THE campaign now being waged to improve the quality of the rock-drill bit is the natural outcome f the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc., on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack f continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination f the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved.

Jan 6, 1921

Annual Meeting,Wallace, Idaho, Nov. 15-16, 1913. The third annual meeting, which was also the eighth consecutive meeting and the second to be held in the Coeur d'Alène district, was held in Wallace, Idaho, Nov. 15-16, 1913, with side trips to Kellogg-Wardner, Larson, and Mullan, where several mills were visited. The meeting was held jointly with the Montana Section, about 50 members and guests being present. Headquarters were in the Samuels Hotel, sessions being held in the public library. The arrangements and program were in the hands of the following local committee: George W. Roddewig, W. Earl Greenough, H. M. Childs. At 2.30 p.m., Nov. 15, the first session was called to order by Prof. F. A. Thomson, member of the Executive Committee, adjournment being taken to the Mine Rescue car, where Mr. Anderson and his assistant entertained the visitors for nearly two hours by demonstrations of mine-rescue and, first-aid practice, after which the party visited the Hercules mill, mention of which was made in the report of last year when the Section visited the plant. There are, however, several important alterations and additions to the flow-sheet to be noted, such as substitution of Chilean and Hardinge mills for the Huntington mills in the regrinding department; rearrangement of the tables and slimers, with a noticeable addition of the later models of the Franz machines, and the installation of the Wyman flotation process, which has been tried out, or is being tested, with more than ordinary success, on the middlings in several of the mills of the district, the Green Hill Cleveland mill being provided with a 100-ton unit, partly described below

Jan 12, 1913

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928

By J. Marshall Rounsevell

It is probably not too far from the truth to say that the sulfur content of the steel bath at the first turndown of the basic oxygen furnace is influenced by every factor which varies in the operation of a BOF shop. However, the determination from normal shop operating data of the effect of a given factor on turndown sulfur content requires a means for collecting a large quantity of such data and a significant variation of the factor in question in that data. In this paper, operating data from 4000 heats collected on the computer at Inland's No. 4 BOF Shop is utilized to analyze the effect of four operating parameters -- hot metal sulfur content, hot metal manganese content, percent burnt dolomitic lime (dolomite) in the flux charge, and the presence or absence of transfer ladle slag skimming -- on first turndown sulfur content.

Jan 1, 1972

By J. J. Jakosky

ALL electrical geophysical methods depend for their operation upon the effects produced by the flow of an electric current. By studying these effects it is possible to predict the general axis of current flow. The greater flow of current is in the path of greatest, effective conductivity; and since the effective conductivity of a mineralized zone is different from that of its surrounding envelope (usually much greater), it is possible to locate such a mineralized zone by the distribution of current. Due consideration must be given, of course, to geological structure, to type of mineralization, and to other factors. A number of methods are used to cause this flow of current, and various methods are available for detecting the presence of such current flow and for studying its effects. In a rather detailed way, this paper will discuss the theoretical and practical phases of the inductive methods of geophysical prospecting. ELECTROMAGNETIC GENERATION OF AN ELECTROMOTIVE FORCE The inductive method is so named because the current flowing in the conductor is obtained by electromagnetic induction, instead of by the use of ground electrodes through which a current is passed as in the applied potential systems, or by direct contact with the orebody. An alternating current flowing in a coil will create an electromagnetic field around the coil. This field will have the same frequency as the current and will radiate or travel outward from the coil in closed magnetic or flux circuits: These flux circuits (in air or a homogeneous medium) will be perpendicular to the plane of the coil and will extend or travel outward with uniform velocity in every direction. Maximum field exists in the plane of the coil. Such a coil used for transmitting or as the "energizer" will exhibit similar figure-eight characteristics to those exhibited by the direction-finding coil which will be described in detail later.

Jan 1, 1928

By Donald Ingvoldstad, Harold E. Lee

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were .provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through ¼in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

By P. F. Gnirk, J. B. Cheatham

The basic objective of this paper is to present a review of the state of knowledge concerning the fundamental mechanics of rock/bit-tooth interaction under downhole conditions. Of particular concern is the contributing significance of the various variables associated with the generation of rock chips by a single penetrating bit-tooth. The variables to be considered are fluid pressures which simulate borehole conditions, the mechanical properties of the rock, the shape and angle of attack of a bit-tooth, and the rate of load application on a bit-tooth. In addition, consideration is given to multiple bit-tooth penetration insofar as the effects of distance from and geometrical shape of adjacent penetration craters are concerned. Both experimental results and idealized theoretical models for single bit-tooth penetration are presented. Finally, the applicability of plasticity theory to drilling phenomena at depth, results of recent drag-bit studies, and several general theories of roller-bit drilling are briefly discussed. FUNDAMENTALS OF ROCK/BIT-TOOTH INTERACTION Drilling efficiency at depth in terms of penetration rate depends largely upon three essentially interdependent factors: 1) the bit, insofar as the mechanical motion, shape, and configuration of the bit-teeth are concerned; 2) the rock, as regards its mechanical behavior, or response to the penetrating action of the bit-teeth, when subjected to a state of stress induced by mud column, interstitial pore, and overburden pressure (and at great depths to high temperature) ; and

Jan 1, 1967

By Robert Glass Cleland

THE BEGINNING of a large enterprise is often as in- significant as a lump of leaven hidden in a bowl of meal or a handful of mustard seed that the wind blows across a field. In 1950 the company known today as the Phelps Dodge Corporation had nearly thirty-two thousand stockholders, paid salaries and wages of about fifty million dollars to some thirteen thousand persons, produced nearly four hundred and ninety million pounds of copper, and possessed net current assets of approximately one hundred and six million dollars. For the origin of this great business, one must go back approximately a hundred and fifty years to an obscure saddle-making shop in the small town of Hart- ford, Connecticut. Anson Greene Phelps, proprietor of the shop and master saddler in his own right, was born in 1781-the year of the Battle of Yorktown, the surrender of Cornwallis, and the close of the Revolutionary War Anson's forebears had come to America in the great Puritan migration that left fields, shops, pulpits, and hearthstones in the reign of Charles the First to transplant the strong, tough roots of their race, culture, and institutions in the New World.

Jan 1, 1952

By J. H. Henderson, R. J. Wygal, J. Naar

Experimental work is reported which shows that consolidated rocks and unconsolidated porous media exhibit different imbibition flow behavior. At a given saturation the imbibition nonwetting permeabilities for a rock are smaller than the drainage permeabilities. The contrary happens for unconsolidated aggregates — imbibition nonwetting permeabilities are larger than drainage ones. A similar difference is observed for the wetting phase. Imbibition permeabilities are larger than drainage ones for a consolidated rock but smaller than drainage permeabilities for an unconsolidated medium. The results of these differences are examined for two cases. 1. Flooding Efficiency — Craig's1 scheme for the computation of production history of a five-spot water flood is shown to agree extremely well with experimental results obtained when using a system packed with glass spheres if imbibition relative permeability curves are used. 2. Alcohol-Slug Displacement — Published theory 2 on oil displacement by alcohol slugs has been questioned despite the apparent agreement between predicted and observed results. The present work suggests that, if imbibition relative permeability curves characteristic of the unconsolidated media used in the early experiments had been available to make the predictions, the inadequacy of the theory would have been immediately evident. The experimental work shows that poorly consolidated formations tend to behave like unconsolidated media. Finally, it is shown that the difference in imbibition behavior is directly related to pore-size distribution and cementation. PART 1 — THE FLOW BEHAVIOR OF UNCONSOLIDATED AGGREGATES Experiments on scaled models of field reservoirs are useful for studying new displacement processes which are incompletely understood. Even when a mathematical description is possible, the solution might be difficult and complex. An answer obtained from a scaled model is extremely valuable in such cases. A great amount of work$-5 therefore, has been devoted to the derivation of scaling laws. Similarity groups have been defined which assume (1) that the relative Permeability curves of the prototype and the model are the same whether the displacement is an imbibition or a drainage process and (2) that there is a linear relationship between the capillary pressure of the model and the prototype. For practical reasons (simplicity in the preparation of models, duration of the experiments, etc.), the porous media of laboratory models are usually unconsolidated packs of sand or glass particles. Hence, unless the capillary and flow characteristics of unconsolidated and consolidated systems are identical, the model data are applicable only to unconsolidated formations. The usefulness of scaled-model studies may then be seriouslyrestricted since most oil-bearing sands are consolidated. Perkins and Collins6 suggested the use of model and prototype curves normalized with respect to both relative permeability and saturation to improve compliance with scaling criteria. Even this technique does not give a satisfactory model-prototype match. This paper reports an observation of two-phase flow in unconsolidated sands which shows that, for most displacements, "scaling" in the strict sense of the word is not even qualitatively feasible with a sand model. It provides, however, a firm foundation for testing a theory by matching it with observed performance of laboratory-size models. EXPERIMENTAL AS a part of a basic study of packed aggregates, the relative permeability of glass-spheres and sand-grain packs was measured with capillary control. The fluids were oil and air' The spheres were packed in plastic cylinders 1-in. in diameter;

By Jack L. Taylor

Single crystals of tungsten grown from powder -metallurgy swaged rod by high-temperative annealing were deformed in tetzsion at temperatures from 2500 to 5000 OF. Orientation of specittzen tensile axis, strained ratrix, and defortnation bands was determined optically by reflections from {110} etch pits. Slip traces meve analyzed and slip directiorz determined. Results indicate that {110}(111) , {112){111}. and {123}{111} type slip occur in tungsten over the terpe,atuve rutge investigated. Slip is orientation-dependent occuvring on tCuzt cowzbitzation oj slip plane and direction which has the highest critical resolved shear stvess. Overshooting appears to be a general occurrence between 2500' and 5000°F. Dejornatiotz bands show rotation in a directiorz opposite to the yotation of tire tensile axis. DEFORMATION in bcc metals has been reviewed by Maddin and Chen,' Keh and eissman,' and most recently by Nabarro, Basinski, and olt. From these reviews it is apparent that some disagreement exists concerning the crystallography of plastic deformation in bcc metals. There is evidence of noncrystallo-graphic slip, the crystal slipping on or near a noncrys-tallographic plane in the (111) zone for which the resolved shear stress is greatest. There is also evidence to indicate that crystallographic slip occurs in the planes of the same zone. On the other hand, there is agreement that the close-packed direction ( 111) is the slip direction in bcc metals. Further, in pure bcc metals4 and alloys the operative crystallographic slip systems are strongly dependent on temperature. Both crystallographic and noncrystallographic slip have been reportede8 in tungsten, a group VIA bcc metal. The number of slip families which operate in the case of crystallographic slip, however, has been in question. The earliest study by oucher' of single-crystal tungsten tested at temperatures of 1800 to 5000°F led to the conclusion that only {112)( 111) type slip operated. Raymond and eumann recently reached the same conclusion studying deformation by rolling of plasma-flame single crystals at 1800°F; however, only [loo] and [110] orientations were studied. Work at high temperatures by Leber and Pughs on tungsten and Chen and Maddin9 on molybdenum suggests that conjugate slip on nonparallel (110) planes may account for the slip on (112) and (123) planes found by others working with bcc metals. The present paper presents evidence of three families or modes of slip in tungsten in the temperature EXPERIMENTAL PROCEDURE Material. Standard microtensile specimens, 0.160 in. diam by 0.640 in. gage length, were ground from commercial powder-metallurgy swaged tungsten rod, type MK. Specimens were heated for 10 min at 5150°F or 6 hr at 5400°F in vacuum of 1 x 105 Torr or less to produce single crystals. At the lower temperature an average of two out of seven specimens heated in a group developed single crystals throughout the specimen length as shown in Fig. 1, the rest remaining wholly poly crystalline. At the higher temperature, three or four out of seven specimens became single crystal. Other than to note that Laue X-ray photographs generally showed sharp, well-defined spots, no attempt was made to assess crystal perfection or measure dislocation density. Two tungsten single crystals grown from the melt by the plasma-arc process were also used for this study.

Jan 1, 1967

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

By W. H. Somerton

The effects of drilling variable on rotary drilling rates and efficiencies have been studied by a series of laboratory drilling tests. TWO-cone 1.25-in. diameter hits were used to drill vertically upwards into rock samples at corltrolled weights and rates of rotation. Shale, sandstone and specially prepared concrete samples were used in this study. Power input to the ririllirig systeln was measured and drilling chips collected for energy — .size reduction studies. Reasouably good correlations between drilling variables and rates of penetrotion were found. Qrrantities that are difficult to evaluate include rock strength parameters and the effects of bit wear. Effects of bit size and geormetry require further investigation. Analysis of the drilling chips confirmed the premise that, for rocks containing two or more mineral constituents of diflerent strengths, a greater amourrt of rock breakage occurs in the weaker constituent. Drilling conditions which required greater amounts of energy produced finer drilling chips. As bit tooth wear progressed, drilling chips became finer. Efficiency of rotary drilling as a rock breakage mechanism was extremely low. Comparison was made with theoretical energy requirements and with energy requirements for size reduction by comminution methods. INTRODUCTION Many technological developments and innovations have made possible the successful drilling of oil wells by the rotary method to depths exceeding 20,000 ft. Bigger, more powerful rigs, better steels, improved bit design and more careful control of the circulating system have all contributed to this success. Despite these advances comparatively little is known regarding the basic mechanism of rock breakage by the rotary drilling process. Future improvements and, in particular, reduction of drilling costs will undoubtedly require a clearer understanding of the variables controlling effectiveness and efficiency of rotary drilling. Rotary drilling is inherently an inefficient means of producing rock breakage. Loss of energy in transmission from the surface to the cutting mechanism may be large, thus limiting the total amount of energy which may be applied to rock breakage. Increased efficiency may be realized by improved energy transmission methods such as the turbodrill. Conversion of transmitted energy to rock breakage by use of rotating cutter teeth is likewise inefficient. Improvement of cutter efficiency has been obtained essentially by empirical means —changes in bit tooth size, shape and spacing, and tooth deletion to give clean bottom-hole patterns. The present work was undertaken to investigate the factors controlling rates of bit penetration under laboratory drilling conditions. Laboratory drilling apparatus is shown in Fig. 1. The effects of rock strength and bit wear on drilling rates were investigated. Drill cuttings were analyzed to determine the character of breakage and to compare this with other methods of producing rock breakage. VARIABLES INVOLVED IN ROTARY DRILLING Some of the variables controlling bit penetration rates can be studied conveniently by dimensional grouping. R/DN f(F/D2S) or

By Hertha Freche

THE diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magne-sium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austen1 carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum.

Jan 1, 1936

By Alfred E. Hunt

Tars paper is suggested by the appointment on the part of the American Societies of Mechanical and of Civil Engineers of committees upon the subjects of " Standard Tests and Methods of Testing," and " Uniform Methods of Tests of Material used in Metallic Structures," respectively, and by a study of the report of one of these committees, and other papers. Moreover, the writer has had frequent occasion to hear the complahts of tnanufacturers who furnish structural material subject to specifications, that in the tests prescribed, the number of tests required, and the methods of making

Jan 1, 1892