Search Documents

By F. W. Apgar

THe valuable results that have followed the application in recent years of microscopic methods of research to problems of ore genesis have been significant, but possibly the recognition of their practical importance is not as general as might be, and while, as a scientific method of investigating ores and rocks, the advantage derived through the use of the microscope is unquestioned, its utility as an aid in solving mining problems arising during actual every-day mine examination and operation may not be fully appreciated. Perhaps the most logical method of showing some of these practical applications of the microscope will be to consider first the prospect stage of a mining venture, then the uses to which the instrument may be put during the operation of a working and developed mine, arid, finally, to discuss some of the problems of a metallurgical nature that may arise during milling and smelting the ore. The valuation of mining property as a preliminary to acquiring ownership or determining the advisability of investing time and money in an enterprise is one of the most important and delicate problems that come before the mining engineer. The many and variable factors that have to be taken into account, as, for example, the geology of the district, availability of supplies, probable mining costs, transportation facilities, and the quality of ore, require a careful balancing of costs against recoverable values. Primarily, however, a study of the local geology is of first importance, since, in a prospect with little development work, the question of character and probable quantity of the ore and its value can only be approximated with any degree of accuracy by a thorough investigation of geologic conditions, and a general knowledge of ore deposits. Unless these are favorable and pay ore reasonably certain, other factors need not be considered. The character of the outcrop, evidences of mineralizing agencies in the adjacent rocks, and geological structure, are the data of chief significance.

Jan 1, 1914

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.'-' A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,' and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By James T. Kemp

SOME interesting and, to American eyes, rather unusual processes for refining impure aluminum derived from scraps were found by American and British investigators who went into Germany in 1945 for the Technical Industrial Intelligence Committee Of the Joint Chiefs of Staff. What was found was recorded in a series of reports (see page 14), many of which have been released for general reading. This paper gathers under one title and summarizes the German work in refining light metal scrap. Reference must be made to the original reports for greater detail. Basically, the occasion and stimulus for the German developments in treating light metal scrap were hard necessity. Germany needed the metal for a rapacious war industry. Adequate supplies of new aluminum from reduction works were not assured. Great quantities of airplane and other light metal war scraps were forecast. It was evident that the scrap metal would have to be reabsorbed by the producing industry and would have to be kept of good quality. The normal current production of manufacturing scrap was being and could be consumed as generated. It offered no technical problem. The mixed scraps, especially those arising from crashed and decommissioned airplanes, however, presented problems of another kind. AIRPLANE SCRAP The recovery of usable aluminum alloy from the mixed assemblies that made up the piles of airplane scrap was attacked in different ways by different groups and with differing degrees of success. Three procedures actually were used On a commercial scale, one was in pilot-plant stage and another had come to a halt in the laboratory a year before Germany collapsed. Four of these five processes actually involved "refining"; that is, some measure of purification of the metal after melting. SORTING AND SEPARATION ON A SLOPING HEARTH The simplest procedure for utilizing airplane scrap involved no refining in the strict sense of the word. This was the practice adopted by two representative plants visited by the author, the Leipziger Leichtmetalle Werke, Rackwitz, Saxony, and the Vereinigte Leichtmetalle Werke, Hanover. These firms did essentially the same thing that was done in England but not with equal success, to judge by their shorter experience, the smaller tonnage handled and by the number and quality of alloys produced. The two German firms named rough-sorted scraps by their easily recognizable alloys, essentially by part and shape. They used hand labor to chop and hack and tear apart. The easily separated heavy metal and nonmetallic scraps were discarded as they were found. Steel and the higher-melting-point metal parts riveted to aluminum or built into

Jan 1, 1947

By W.G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By W. G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

By B. A. Eaton, K. E. Brown, C. R. Knowles, D. E. Andrews, I. H. Silberberg

This paper presents the resitlts of an investigation of two-phase, gm-liquid flow in horizontal pipelines. Experimental data were taken in three field-size, horizontal pipelines, two of which were constructed for this purpose. The data were obtained using water, distillate and crude oil separately as the liquid phase, and natural gas as the second phase. Experimental pressure-length traverse, liquid holdup and flow-pattern data were collected for each set of flow rates. These data were used to develop three correlations that are presented herein. The liquid-holdup values correlated with various flow parameters without regard to the existing flow pattern. The same was true for the energy-loss factors. A new flow-pattern map is presented that appears to be quite reliable, but not required for the pressure-loss calculations. The liquid-holdup correlation and the energy-loss factor correlation are used in conjunction with a two-phase flow power balance, developed during this study, to predict the pressure losses that occur during gas-liquid flow in horizontal pipelines. A recommended calculational procedure is given, as well as a statistical analysis of the results. This procedure lends itself to computer application, since several small pressure decrements are needed to calculate a pressure-length traverse. The correlations are shown graphically, but may be curve fitted with existing curve-fitring computer programs. INTRODUCTION Due to the frequent occurrence of gas-liquid flow in pipelines and the desire to accurately calculate the pressure losses that occur in these lines, two-phase flow is of considerable interest to the petroleum, chemical and nuclear industries. In the petroleum industry, gas-liquid mixtures have been transported over relatively long distances in a common line due to the advent of centralized gathering and separation systems. Long two-phase flowlines are usually accompanied by large pressure drops which influence the design of the system. Gas-lift installations are designed on the basis of known tubing pressures at the wellheads. The horizontal flowline connecting the wellhead and the separator system must be correctly sized in order to minimize the horizontal flowline pressure losses and the wellhead tubing pressure. Practically all oilwell production design involves horizontal two-phase flow in pipeknes. All of the flow processes of oil and gas production must be studied simultaneously to insure good well design. Since the beginning of offshore oilfield development, long horizontal flowlines have been constructed. Because pressure losses greatly influence the performance of producing wells, a method is desired that can be used to predict such pressure losses and select optimum flowline size. Several types of gas-liquid flow exist, and many of these are discussed by Gouse The study of pressure gradients, fluid distributions and flow patterns that occur in horizontaI multiphase flow is made difficult by the great number of variables involved. The various flow regimes give rise to changing velocities of the fluid particles in all directions. These instabilities of the interface between the gas and liquid prohibit the determination of actual vector velocities of fluid particles in each phase. Also, it is practically impossible to arrive at correct sets of boundary conditions. Therefore, most investigators have concluded that a solution to the problem by the classical fluid dynamics approach, whereby the Navier-Stokes equationsM are formulated and solved, is far too complex. Other methods must be utilized to develop general correlations that will predict the behavior of gas-liquid horizontal flow systems. Multiphase flow studies have sought to develop a technique with which the pressure drop can be calculated. Pressure losses in two-phase, gas-liquid flow are quite different from those encountered in single-phase flow; in most cases an interface exists and the gas slips past the liquid. The interface may be smooth or have varying degrees of roughness, depending on the flow pattern. Therefore, a transfer of energy from the gaseous phase to the liquid phase may take place while energy is lost from the system through the wetting phase at the pipe wall. Such an energy transfer may be either in the form of heat exchange or of acceleration. Since each phase must flow through a smaller area than if it flowed alone, amazingly high pressure losses occur when compared to single-phase flow. Most investigators of horizontal two-phase flow phenomena have chosen to separate their experimental data into several groups of observed flow patterns or regimes.

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen's hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By H. A. Schwartz

FROM time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion1 of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composition: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213° to 1132° C., the latter figure agreeing with Gontermann's data .2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the metastable diagram, from a temperature somewhat below the eutectic freezing point to a temperature below Ar1 and for a graphitic-carbon content from practically nothing to the original total carbon of the specimen (see Fig. 6). More especially we desired to locate the line in the stable diagram corresponding to the Acm line of the metastable system, which is designated by analogy, the Atm line (tm from temper carbon) ; also to determine the location of Aim with respect to Acm toward their lower extremities at Ar1 in order to determine whether or not graphitization is completed by the separation of an iron-carbon eutectoid analagous to pearlite in the iron-cementite system. This would involve further a comparison of the locations of the stable and metastable A1 points.

Jan 8, 1922

By C. C. Harris

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale-down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By Ronald D. Irving

The object of the present paper is to give an outline account of the mineral resources of the State of Wisconsin, so far as they are now known, including both metallic ores and non-metallic useful mineral substances. Tl~e only previous publication making ally attempt at such an account is one of a popular nature, prepared by the writer for Snyder and Van Vechten7s Historicccl Atlas of Wisconsin, which was published at Milwaukee in 1878. The data upon which the statements of the following pages are based are chiefly from the

Jan 1, 1880

By G. L. Oldright

THE upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the opera-tion of sintering. A sinter feed with normal gangue constituents, con-taining more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead con-centrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1940

By Ferid Kromer

This paper is the first in a series which will describe geology, mining methods, and production costs of some, of Turkey's more important minerals. In this paper the economically significant minerals-chromite, meerschaum, and magnesite-of the Tagtepe district are described. The cost data presented are believed by the author to be the first made public on Turkish chromite mining.

Jan 1, 1950

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy's law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950's, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

By William R. Barton

Iron and steel slag represent man's most successful attempt to date to profitably utilize a solid waste. Its consumption represents a solution to a solid waste problem and also represents tonnage of natural aggregates that will not have to be mined with concomitant disturbance of the land. Slag has been produced as long as iron has been made; but until a little more than 50 years ago, it was mostly a waste product to be disposed of with as little effort and cost as possible. Huge piles of waste slag were generated over the years of iron and steelmaking. Sporadic use was found for small amounts starting with slag (from Catalan forges) used for road bases by the Roman Empire. The first recorded sustained commercial use was, as is often the case in man's history, for making war. Some profit- conscious munitions maker in the 16th century realized that he could make cannon balls of slag instead of the more precious iron. Other small-volume uses gradually developed: cast building blocks, slag-lime mortars and cements, slag wool, ballast, road base, and, finally, in concrete. But it was not until after World War II that the true potential of blast-furnace slag as a construction aggregate was really recognized. Now nearly all blast-furnace slag produced is used, and much of the earlier stock- piles in the U. S. have been reduced or entirely consumed. Steel slag for aggregate use has been in commerce for only the past 10 years, and use has increased rapidly (10-50% per year) during the past 5 years as blast-furnace slag supplies became depleted. However, much remains to be accomplished in determining character and optimum conditions of use for various types of steel slags before such slags will realize their full use potential. Although slag represents only 2% of construction aggregate materials used in the U.S., its production involves certain features that make its production record far more important than national tonnage figures would indicate. Its source is in iron and steel production and concomitantly slag availability is restricted to those areas where iron or steel is produced. In such areas, it often represents one of the principal aggregates marketed and, because of special properties that make slag a selected aggregate for certain uses, the tonnage imbalance may be overcome by the importance of its contribution to quality or special characteristics of end products. The location and number (Fig. 1) of slag plants handling this annual production is governed by the geographic makeup of the iron producing industry. Prior to the period marked by World War 11, most blast furnaces were in the Great Lakes area-Pittsburgh, Cleveland, Chicago, Gary, Buffalo, Detroit, Youngstown, and Toledo, with exceptions at Baltimore, Bethlehem, and Birmingham. Since that time, iron and steel facilities have been established in Texas, Utah, and California. Today 85 slag plants in 15 states provide employment for almost 2000 persons. The slag plants also recover almost 4 million tons of slag-encrusted iron each year for return to the blast furnaces. Much of the success in developing uses for slag can be attributed to the efforts of the National Slag Association founded in 1918. Since then, it has conducted numerous field and laboratory investigations to demonstrate the properties and uses for slag and slag products. These investigations have resulted in total recognition of blast-furnace slag as a construction material of consequence. The American Society for Testing & Materials Designation C125 recognizes blast-furnace slag as "the nonmetallic product consisting essentially of silicates and aluminosilicates of

Jan 1, 1975

By M. A. Cook

Sutherland used an ion-pair adsorption model to derive the author's hy-drolytic pee-acid) adsorption equation for the contact bubble curves of Wark and Cox. To do so it was necessary to postulate that the sum of coverages of surface anion sites by the collector and depressant anions is practically unity. It is here shown that the free energy of Sutherland's postulated collector ion (x-)-depressant ion (OH-) exchange reaction (for no other than the OH- to compete with X-), namely EX + (OH-) Z SOH- + X-, is in some cases positive and X- should not even adsorb. Also, in many cases the (OH-) adsorption must be quite negligible even though the collector covers only about a sixth of the mineral surface at the threshold of air bubble contact. This, however, contradicts the postulate that permits one to derive the correct bubble contact eqwztion for the ion-pair model. Furthermore, the requirement for charge neutrality leads in the ion-pair model to the (impossible) constancy of the ratio @+)/(OH-) along a contact bubble curve in which pH may change by more than seven units. HYDROLYTIC ADSORPTION EQUATION Hydrolytic (free-acid or free-base) and ion-pair (H', X-, or R', OH-) adsorption models of the collector in metal sulfide and similar flotation systems are superficially alike and somewhat difficult to differentiate. This is because they yield, under seemingly valid assumptions, equivalent forms of the equations describing the distribution of the collector between the aqueous solution and the mineral surface. This has been discussed by the author and associates1-4 and more recently by Sutherland,' both for simple collector-mineral and for more complicated collector-depressant-mineral systems. In the hydrolytic adsorption model the equations describing the contact bubble curves of Wark and coxeJ7 are as follows :2 Here X is the collector anion, D- the depressant anion, 9, and On are the fractions of the free-acid sites S on the surface of the mineral covered by collector and depressant free acids, respectively, and @ is the fraction of uncovered sites. Kx is the free-acid collector dissociation equilibrium con- stant, K1 that for the free-acid collector adsorption, KD that for the free-acid depressant dissociation, and K2 the equilibrium constant for the free-acid depressant adsorption. Eqs. 1 to 5 yield upon simultaneous solution the result is the critical free-acid concentration for bubble contact in the absence of depressant-free acid. Eq. 8 expresses the conditions along a simple collector-mineral contact bubble curve for the case HD = 0, or V = 0. Last and Cook showed that Eq. 6 applies generally and with good accuracy in the collector-depressant-metal sulfide mineral systems. Inci-dentally, it has been shown by infrared absorption studies that in some cases the free-acid adsorption process splits out water.' In this case, Eq. 2 might be written SHOH + HX Z SHX + H20, with a similar equation replacing Eq. 4 for depressant-free acid-water exchange. This possibility does not change, however, the basic equations or considerations of the hydrolytic adsorption model. Indeed, this type of free acid-water exchange reaction was predicted for fluorite and iron ore flotation by oleic acid in the dry grinding and boiling processes.410

Jan 1, 1961

By Jun-Yan Chen, Stefan H. Boshkov

Metal mining in the People's Republic of China has shown great growth during the last three decades. Over 150 new iron ore mines and nonferrous base metal mines have been opened since 1949, althouc.11 most of them of medium and small size. Concurrently, many old mines were enlarged and reconstructed. The production of iron ore has grown from less than 1.5 million tons per year in 1949 to almost 76 million tons in 1978. A corresponding increase in the total annual output in the nonferrous metal mineral industry has also been noted. It is well known that the PRC is very rich in metal mineral resources. The reserves of tungsten, tin, antimony, molybdenum and iron ore are ranked in the top three in the world. Recently, some copper porphyry ore deposits were discovered in Jianxi and Anhui provinces. Some large nickel-copper sulfide deposits were discovered and have been developed in North- West China. Huge iron ore deposits have been found in Liaoning, Hebei and Szechwan provinces. However, the bulk of the iron ores are low grade. The growing metal mineral production has met basic domestic needs since 1949; it has also proven China's big resource potential. Mining methods have also undergone development in the past 30 years. About 80% of the annual output of iron ore comes from open pits, whereas about 58% of nonferrous metal ores come from underground mines. Blasthole open stoping, sublevel caving and induced block caving are widely used in Chinese underground metal mines (table 1). This paper summarizes in detail the planning for and application of these three bulk mining methods in the nonferrous and iron ore mines in China. CLASSIFICATION OF UNDERGROUND MINING METHODS The main principle of the classification of underground mining methods in PRC is ground support in the stoping cycles of the mining blocks or stopes. Table 2 lists this classification. It is essentially the same as that given in the SME Mining Engineering Handbook. Be- cause pillar removal is a secondary mining operation, using a variety of methods, they are not included in this classification. As is the case with most classifications in science and technology, there is no precise division between the classes of mining methods. Because of the rapid development of consolidated filling techniques in the past twenty years, some types of open stoping methods use fill in order to improve the ground conditions for the secondary recovery stage. Thus, these mining methods have features of both methods using no artificial support and those using artificial support. In this classification, this type of mining method is placed in the latter category. The shrinkage stoping method has been employed extensively to mine steeply dipping narrow veins of tungsten and tin in the Jiangxi, Hunan, Guangdong and Guangxi provinces. Shrink- age stoping is placed under the class of mining methods without artificial support be- cause this reflects the nature of the Chinese experience. The function of the broken ore serving to support the footwall and/or hanging wall is limited, because the expectation is for the host rocks to remain unsupported until the stope is drawn empty. APPLICATION OF BULK MINING METHODS Bulk mining methods consist of blasthole open stoping, sublevel caving and block caving. These stoping methods have much in common, such as: bulk ore materials blasted by long holes; higher production rates of stopes or blocks and higher production efficiencies of the whole mining systems.

Jan 1, 1981

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968