Search Documents

Jan 1, 1967

By T. L. Joseph

IT is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that under- lies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book1 on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blast- furnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1946

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act; the Norris-La Guardia Act; the Wage and Hour Law; the Walsh-Healey Act; and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously with- out regard to the interests of management, the employes, or the public. This chapter deals with the various phases of labor-management relations as they affect the principal segments of the mineral industry in North America. To the greatest extent possible available data is presented pertaining to the unions involved, their relative strengths, labor law, compensation and fringe benefits of employes, working conditions, and related matters. As background, the historical development of union-management relations in the respective segments is included where possible. The section dealing with the United States has been divided into separate

Jan 1, 1959

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By M. Sagheer

This paper gives a report of the laboratory work investigating the fundamental flotation characteristics of chromite and its commonly associated mineral, serpentine. Floatability curves, showing floatability of chromite at different concentrations of sodium oleate and pH, were obtained by pick-up method. One of the difficulties encountered in flotation of chromite in presence of serpentine has been attributed to dissolved metal ions. The influence of metal ions, dissolved in pulp filtrate, on floatability of pure chromite and serpentine has been studied and it has been shown that Mg, Ca and Fe ions depress chromite. A considerable amount of work applying bubble pick-up method was carried out to counteract the depressing action of metal ions. Various methods and reagents were applied in this connection. Validity of each method and reagent has been discussed. Probably due to the abundance of high-grade chrome ores, very little has been published concerning the flotation of chromite. As improvements in mineral beneficiation are realized, more attention is being directed to low-grade ores previously considered unusable. Currently, gravity concentration is the principal process applied to upgrade chrome ores, but this cannot be used for finely disseminated ore because of the substantial losses in the fines,1,2,3 To avoid these losses, flotation can be applied to material which is too fine for satisfactory gravity concent ration, and it is probable that a combination

Jan 1, 1967

By W. E. Forsythe

WHEN measuring ordinary temperatures, the instrument is generally placed in very close contact with the body the temperature of which is desired. However, if the temperature of the source is continually raised, a point is soon reached where no known substance will, in general, remain constant in any of its temperature-measuring properties if placed in direct contact with the source. Also, it is occasionally necessary to measure the temperature of a source that 'is so small or so situated that it would be very hard to bring the measuring instrument into direct contact with the source. When these conditions exist, advantage is taken of the well-known fact that all bodies, when at sufficiently high temperatures, send out radiation in amounts readily measurable. This radiation has been found to be related to the temperature. The temperatures of very hot bodies have probably always been judged by the color, or the brightness, of the light given off. With practice, one can estimate probably within 50° to 100° C. of the correct value. However, if judgment is left to the eye alone, very much larger errors are sometimes made, due to

Jan 9, 1919

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Robert Glass Cleland

FROM the time of its organization down to 1917, a period of more than eighty years, Phelps, Dodge & Co. was seldom involved in what could be called a major labor difficulty. Behind this remarkable record lay both a philosophy and its practical application. The philosophy was an attitude toward society called the Golden Rule. That philosophy had been a living principle in the lives of the founders of the company, Anson Phelps, Daniel James, and William E. Dodge. Their successors, William E. Dodge, Jr., and Daniel Willis James, accepted the same philosophy. Dr. James Douglas governed his life by it. All of these men and their families had given tangible expression to that conviction in benefactions of great magnitude and variety-churches, hospitals, educational institutions, libraries, missionary undertakings, and other organizations for human betterment, such as the Young Men's and Young Women's Christian Associations, and the development of model communities about their mills and factories. According to the best standards of their generation, they had sought to improve the condition of labor,

Jan 1, 1952

By F. J. Schuh

The drilling industry long has been plagued by failures in the bottom few joints of surface and intermediate casing strings. This paper presents an analysis of the various possible causes of failure and concludes that failures are caused by short-lived, high-energy torque impulses delivered from the drill string through the bit while drilling out the cementing plugs, cement and floating equipment. The magnitude of these torque impulses is shown to be a function of the rotational momentum of the drill string, and a method is derived to calculate the magnitude of these impulses. The available methods of strengthening the bottom joints are reviewed. It is concluded that, while present methods are ineffective, a combination of improved procedures for strengthening and minor restrictions on drillout practices will prevent failures. Introduction In most cases, failure in the bottom few joints of casing strings is not discovered until electric logs record that the bottom one, two or three joints have parted from the casing string and slipped down the hole. However, in some cases the parted section of casing uncovers a high-pressure or lost circulation zone, or shifts laterally restricting the passage of drilling equipment. In these instances extensive remedial work is required to realign the parted pieces and seal the exposed formations. Several methods used to strengthen the bottom joints of casing strings include locking set screws in the couplings, putting wedges in special collars, welding straps across the couplings, welding the couplings and, most recently, using epoxy resin-based, thread-locking compounds. Since none of these techniques has eliminated the problem, this study was initiated to find the cause of failures and to evaluate the available methods of prevention. Mechanics of Casing Failures An analysis of the various possible causes of failure indicates that the casing is unscrewed rather than broken and that therefore failure must occur before the shoe is drilled. Since there is no general agreement as to the causes of casing failure, some possible mechanisms were ATLANTIC RICHFIELD CO. DALLAS, TEX. considered in this analysis. Failure of the bottom joints of casing can occur by only one of three types of stress: tension, torsion or bending. The possible mechanisms of failure were evaluated by determining the forces required to cause casing failure by each of the stresses; and, where applicable, the possibility of failure by fatigue was considered. For casing to part under tension requires a downward load of more than the tensile strength of the casing. The lightest API weight H-40 grade casing requires a bit load on the bottom of the casing of 27,000 to 34,000 Ib per inch of bit diameter (Table 1). Since maximum drill collar weights seldom exceed 10,000 Ib per inch of bit diameter, it is apparent that casing strings cannot be parted by the downward load of the drill string. The second mechanism considered was failure by bending. This mechanism requires that the lowermost casing joints be free to be deflected laterally until the bending stress exceeds the strength of the pipe. To fail, the casing (at a height L above the shoe) requires a force and deflection' at the shoe of To deflect the casing shoe with the drill string obviously requires a dog-leg at the casing shoe. This dog-leg must have a rate of change equal to or greater than the change in curvature of the deflected casing, which is given by

Jan 1, 1969

By Henry M. Howe

THE death of Sir Lowthian Bell removes almost the last of the group of heroic leaders who made their age and ours the Age of Steel-a group which his luster and the luster of his peers, Bessemer, Siemens and Tunner, made one of the most brilliant, perhaps even the most brilliant, in the annals of industry. Born on February 15th, 1816, in Newcastle-on-Tyne, he was the eldest son of Thomas Bell, an alderman of Newcastle, and of his wife Catherine Lowthian of Newbiggin, near Carlisle, in Cumberland, and was christened Isaac Lowthian, the name of his maternal grandfather. His father was born about 1788, and came in 1808 from Newbiggin to Newcastle, where he entered the office of the Cumbrian firm of Losh and Company, manufacturers of alkali and wrought-iron, at the Walker Iron and Alkali Works, at Walker, Dear Newcastle. Young Isaac Lowthian Bell was educated at Dr. Bruce's school in Newcastle, whence he went to Germany and Denmark, learning there German and Danish. On his return he studied at Edinburgh University, and then at the Sorboune in Paris. As a student he already showed the remarkable character and application which later gained him such distinction. After studying the manufacture of alkali near Marseilles, he returned, and when about twenty years old (A.D. 1836) was employed in his father's firm, then called Losh, Wilson, and Bell. After spending a year in their Newcastle offices, and after visiting the important iron-making districts of France, Germany, Poland, and Austria, he took charge of their rolling-mills at Walker, and profited so well by his opportunities, and especially by the teachings of his father and of Mr. John Vaughan (later one of the founders of the great firm of Bolckow, Vaughan & Co.), that he was made manager of the Walker works in or about

Sep 1, 1905

Jan 1, 1896

By F. Twyman, D. M. Smith

THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928

By M. D. Flavel

The paper describes the physical aspects of the compression and impact crusher types along with the information needed to apply, install and operate them to best achieve designed performance levels. It reviews key performance parameters such as energy size relationships for crushing processes and how automation devices can optimize machine productivity. Weaknesses of existing application engineering methods are discussed. The use of pilot plant information and appropriate laboratory testing procedures are reviewed from the point of view of the application design engineer so that the best type of machine can be selected for a proposed installation.

Jan 1, 1982

Your committee's secretary submits the following report, or summary, to the- members of the committee, in an endeavor to lay before them a general review of the information so far received and also his own knowledge .of the work as carried on at a number of plants, this being done in part to secure further information and suggestions from members and lead to a more effective means of furthering the work of the committee. It is suggested that more detailed data be compiled regarding engineering features involved, and that papers be contributed which will deal with the safeguarding of underground electrical installations. There are few operating companies which have not started a more or less systematic campaign to safeguard their employees from accidental injuries and unhealthful surroundings, but a great deal is to be gained by experience. All may welcome the advice and cooperation of those who have been actively engaged in the work and have demonstrated the results obtainable by organized effort, and it is, therefore, exceedingly gratifying to note the ready assistance and hearty cooperation rendered by the companies that may be truly termed pioneers in the movement. No solution of the safety problem is to be found in a strict standardization of methods, rules or devices, as' the various mining, milling and metallurgical practices present too' many conditions differing broadly in general principles, but some standard system embodying principles, already proven to be efficient should be created, which may be modified or elaborated to meet specific requirements of each individual. company, or to fit working conditions as they exist in the various mining camps throughout the country. An industrial plant is -primarily a business undertaking, therefore the economic side-of a safety or welfare campaign is of importance. Many small operators have been deterred from undertaking the work by their belief that it involved an expense beyond their means, and one that could not be counterbalanced by greater efficiency or saving along other lines. This idea is generally clue to a lack of knowledge of the actual costs of such work, and of the results secured by judicious selection of a method commensurate with the. size and nature of the opera-

Jan 1, 1917

By L. A. Mekler

THE recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are .constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to that produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack.

Jan 1, 1928

By Simon Ash

THE coal-mining districts of Washington are mainly west of the Cascade Mountains; Fig. 1. The mines are on the foot hills of the slope, the lignite fields of Lewis and Thurston counties extending into the valleys west of the mountains. An exception is the Roslyn field, a small but important area on the eastern slope. If western Washington is divided into three areas from north to south, the bituminous coal fields and most of the active operations will be found largely in the middle area. The southern portion contains lignites over a large area. In the northern portion, mining is practically restricted to one mine, the Bellingham, which is working a subbituminous coal seam near the city of Bellingham. The degree of alteration that the coal of a particular field has undergone may be gaged roughly by the position of the field with reference to the Cascade Mountains. The lignites of Tenino, Tono, Mendota, and Castle Rock, on the railway line connecting Seattle and Portland, occur in a region, of low relief, in which the Eocene coal measures have suffered only minor disturbances. Subbituminous coals occur in the foot hills, as at Renton, Newcastle, and Bellingham. Coals high in fixed, carbon are found nearer the mountains, where. the measures have been sharply ,tilted and folded, as at Black Diamond and Carbonado. The two typical anthracite fields are located still higher, in the rugged mountains where outcrops appear both in deep gorges and on ridges at elevations approaching 5000 ft. At. Carbonado is found the only semianthracite seam worked on a commercial basis. The occurrence of this seam in a region of bituminous coal is due to the nearness of an igneous sill, which has changed its character from bituminous to semianthracite.

Jan 3, 1925

Contents A-Metal Mining B-Minerals Beneficiation F-Coal

Jan 11, 1951

By George B. Clark

COMMERCIAL strip mining of coal was first begun in the state of Illinois in 1911.1 The annual tonnage of coal produced from coal strip mines in the state was very small until 1924, when the strip mines shipped 1.68 pet of the total state shipping mine tonnage. Since then, strip mines have gradually come into their own by producing a sizable percentage of the coal produced in the state. Table 1 shows the coal tonnage shipped from both underground and strip coal mines in the state of Illinois for selected years. The table illustrates the major role that strip mines play in the state's coal industry. Today, strip mining is generally conducted in areas where the coal seams lie so close to the surface of earth that a stripping method of mining the coal seam is cheaper than an underground method. Strip mining not only recovers 100 pct of the coal deposit, but may also be used as a method of mining large acreages of coal abandoned by the closing of underground mines.

Jan 1, 1949