Search Documents

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33' API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By John A. THOMPSON, Pazcl D. Torrey, Frank Breayster

DISCOVERY of natural gas in the Dundee field of New York in February, 1930, and the subsequent discovery in Tioga in September of that year, focused the attention of the natural-gas industry on the enormous possibilities of production and distribution in - the most populous area of the United States-New York and New England. Prior to 1926 the natural-gas industry in New York State had settled into a definite and limited policy, with the distributing companies controlling the output from its discovery to the ultimate consumer. Production amounted to between G and 7 thousand mil- lion cubic feet a year, with another 10,000 million feet imported from Pennsylvania for distribution in New York State. This gas was primarily from the Medina sand stone in. the western part of the state.

Jan 1, 1932

By G. W. P. Rengstorff, H. B. Goodwin

A method is described for purifying iron in batches of 150 Ib or more. Oxygen, carbon, nitrogen, and sulphur are removed from flakes of electrolytic iron by treatment in wet and then dry hydrogen. A special consumable-electrode arc furnace is used to remove hydrogen and to melt the flakes into ingots. A LTHOUGH iron and steel have been made and used for hundreds of years, there are still wide gaps in the knowledge of these metals. One reason for this is that the true properties of the base metal, iron, are not well known, simply because really pure iron has never been readily available for research purposes. Commercial iron, and even the "pure" irons which are readily available, are really complex alloys of iron with oxygen, nitrogen, hydrogen, carbon, sulphur, silicon, and other elements. With such materials, it has not been possible to prepare steels and other iron-base alloys in which all elements are present in exactly controlled amounts. It is an almost impossible task to determine the separate effects of each element or the intereffects of several elements unless alloys can be prepared containing only the desired elements. The ability to make controlled alloys of low impurity content is of far more than academic interest. It will assist in the study of such practical problems as the brittle failure of ship hulls or high pressure gas pipelines, determination of the factors which affect the deep-drawing properties of steels, the improvement of magnetic and electrical properties, the phenomenon of aging, and many others. In 1949, the American Iron and Steel Institute asked Battelle Memorial Institute to prepare high purity iron on a larger scale than had been attempted up to that time. The work was directed toward the preparation of iron as low as possible in carbon, oxygen, nitrogen, hydrogen, and sulphur because these are the contaminating elements of major interest in many research investigations on iron-base alloys. The initial goal was to prepare iron with not more than a few thousandths of one percent of each of these impurities. The purpose was to set up a "bank" of high purity iron on which researchers could draw when a supply was needed and which could be replenished from time to time as the stock became depleted. Of several possible purification methods, heating in hydrogen was selected as the most promising for the removal of both carbon and oxygen from solid iron. Metallic impurities are not removed by hydrogen. Electrolytic iron was chosen as a starting material because it is the most readily available form of iron low in metallic impurities. Decarburization and desulphurization were obtained by annealing in wet hydrogen at relatively low temperatures. The optimum temperature, as found by previous investigators,' is about 1400°F. This treatment also removes nitrogen. Deoxidation is favored by dry hydrogen and higher temperature. There is evidence from previous work that an anneal at 2200°F in dry hydrogen will deoxidize the iron, reduce the nitrogen content, and reduce the sulphur content. These facts suggested the use of a two-stage process: treatment in wet hydrogen followed by treatment in dry hydrogen. To carry out the purification process in a reasonable time, it was necessary that the iron be in thin pieces. Flakes of electrolytic iron were used. Because most research requires that the iron be in massive form, it was nccessary to melt the purified iron to consolidate it into large pieces. For this work, it was decided to prepare ingots weighing at least 15 lb by using a cold hearth arc-melting process in which the iron was melted in an inert atmosphere of argon or helium. This method of melting was selected because the water-cooled copper crucible is not wet by the iron and does not contaminate it as a refractory crucible would. Because the crucible is also the ingot mold, contamination from mold materials was also eliminated. Contamination from electrodes was avoided by making them from purified electrolytic iron. The melting procedure finally developed was an adaptation of the Kellogg electric ingot process.' Two batches of purified iron weighing about 100 Ib each in ingot form were prepared with analyses as shown in Table I. The remainder of this paper describes the procedures in more detail. In general, the process con-

Jan 1, 1956

By R. E. Grant

THE Cerro de Pasco Railway Co., owned and operated by the Corporation, is a common carrier whose chief functions are transportation of ore and concentrates from the mines at Cerro de Pasco to the smelter in Oroya, and haulage of coal from the coal mines at Goyllarisquisga to the coal washery at Fundicion. Connecting with the Peruvian Central Railway at Oroya, the C. de P. Railway maintains joint, daily freight and passenger service from Lima and the port of Callao to Cerro de Pasco, terminal of the C. de P. main line and gateway to the Huanuco Valley. Extending from Oroya to Cerro de Pasco the main line is a standard-gauge roadbed of 70-lb. rail, 132 km. long with a maximum compensated grade of 2.25 per cent and a curvature of 16°, climbing from an elevation of 12,272 ft. above sea level at Oroya, lowest station on the line, to 14,208 ft. at Cerro de Pasco. The highest point reached by the C. de P. is on the coal branch at Alcacocha where the rails are 14,385 ft. above the sea.

Jan 1, 1945

By F. N. Koepel, L. A. Callaway

The property of the Andes Copper Mining Co. is in the central part of the Republic of Chile, Province of Atacama, about 75 miles to the eastward from the port of Chafñaral. At this point the Andean system is made up of two principal ranges, and the mine and metallurgical plant are both on the westerly slope of the outer or western range. Mean elevation of the mine is 10,500 ft., while at the plant the elevation ranges from 9445 to 9700 ft. A meter gage railroad extends from the company's port at Barquito, near Chañaral, to the reduction plant at Potrerillos. This road has a total length of 94 miles, of which 57.79 miles are owned by the Andes Copper Mining Co. and the remainder of the road is controlled by the State. Development of the Potrerillos mine and installation of the metallurgical equipment presented unusual difficulties due to the arid nature of the country, high altitude and remoteness of the location from any considerable center of population. As a primary step it was necessary that railroad transportation be provided in order that mine development and plant construction could go forward on an economical basis. Provision of an adequate supply of water for domestic and metallurgical uses involved the construction of approximately 178 miles of pipe lines, all of which have their sources at altitudes ranging from 12,000 to 14,000 ft. above sea level and traverse rough and difficult terrane. Water for metallurgical use is brought to Potrerillos from the Ola River, a stream originating in the high cordillera to the eastward from the property. It is delivered by means of a steel pipe line, 32 miles long, having diameters ranging from 22 to 36 in. Domestic water is supplied to the various camps through a system of pipe lines aggregating 146 miles in length, the Ola water being unfit for this purpose. These conductors gather water from numerous springs in the high mountains to the eastward from Potrerillos and deliver it to the mine, the reduction works and the port at Barquito. Extensive permanent housing facilities had to be provided as it was necessary to care for more than 3000 workmen and employees at the

Jan 1, 1934

By D. C. Lindley, D. H. Gaucher

The displacement of oil by water in a waterflood project is accomplished by the action of transient viscous, gravitational and capillary forces which drive fluid through interconnecting pore spaces toward production wells. The relative importance of each of these forces to the effectiveness of the displacement and the production history depends on properties of the reservoir itself and the manner in which it is operated. There has been considerable discussion'-3 concerning the importance of these factors and the extent to which they control the performance of individual waterflood projects. No data have been presented, however, to demonstrate the effect on waterflood behavior of variations in rock permeability, water-injection rates and mobility ratios in three-dimensional reservoir systems in which viscous, gravitational and capillary forces are allowed to assume the proper relative influence on fluid flow. Much information relevant to water flooding has been gained from the study of field case histories. But, the complexity of the systems involved, the difficulty of defining geometry and obtaining sufficient data, and the fact that the same reservoir is never flooded twice with the same initial conditions, all obscure the role of process variables such as rate. Further, mathematical calculations of waterflood behavior are restricted at this time by available mathematical techniques to highly simplified situations. Scaled models, however, do offer an approach at the present time to evaluation of the effects of the pertinent variables. Several investigators have predicted prototype reservoir behavior from observations of model waterflood performance under a variety of conditions. Two-dimensional aspects of waterflood pattern efficiency have been investigated by Muskat, Aronofsky, Dyes, et al, raig, et al,' and Rapoport, et al. he effects of gravity segregation, viscous fingering and permeability stratification have also been studied in two-dimensional models. Craig, et al," studied the importance of gravitational forces on frontal displacement in three-dimensional models with wells on a five-spot pattern. This work in- vestigates the tendency for water to segregate in homogeneous reservoirs because of gravity and to under-run the oil for a range of water-inject ion rates. The effects of permeability stratifications were investigated by these authors using miscible fluids to simulate water-channeling through permeable strata in systems of negligible capillary force. In this investigation, a three-dimensional model of a five-spot pattern flood was designed to represent typical prototype conditions, and the sand and liquid properties were selected so that capillary, gravitational and viscous pressure gradients were scaled. It was not, however, possible to achieve exact similitude regarding viscous fingering when the more viscous oil was used. The effects of rock stratification on waterflood behavior were studied by changing both the permeability ratio and the position of the more permeable sand stratum in a two-layered, horizontal model. For each type of stratification, constant-rate floods were performed and the rates were varied, in separate experiments, over a tenfold range. To observe the effect of mobility ratio on flood performance, two series of constant-injection-rate floods were performed on the most highly stratified reservoir at a water-oil viscosity ratio of one.

By Thomas V. Falkie, Robert Stefanko

Much has been said and written recently about the manpower problem in the mining industry. The coal segment of the industry has been scrambling to staff and man its companies and operations in order to accommodate the current boom, and there are some interesting side- lights and developments which deserve further attention from coal mining people. This column will deal with the manpower problem in general and the plight of the professional-the mining engineer-in particular. At this point in the game, it is desirable and perhaps necessary to ask ourselves if there really is a manpower problem and, if so, how serious it is. Suprisingly, there are varying and conflicting answers to this question. If we are talking about warm bodies, then in most mining areas there is no problem. If, however, we are talking about skilled or trained people-at all levels-there are apparently serious shortages, especially in the coal industry and in the U. S. Bureau of Mines. To define quantitatively the present and future need for mining professionals is a formidable task, to say the least. Without pretending that these figures are anything but an educated guess, we feel there is an immediate need for about 1000 mining engineers right now and a continuing need for about 300 mining school graduates per year (double last year's number) for the next ten years in order to take up the slack, provide for attrition and maintain a normal growth rate. Mining companies, large and small, are just now beginning to realize that the industry is undergoing a revolution, It is no longer possible to design, build and operate coal mines by the "seat of the pants." Production demands, the new health and safety law and the inevitable new legislation on surface mining will require more engineering, more planning and new technology. There are mine operators who need mining engineers and don't even know that they need them. This could mean rough going for the small operator. It surely means that there will be a trend toward increasing the ratio of technical to nontechnical employees and the ratio of technical employees to dollars of capital towards levels comparable with other highly mechanized industries.

Jan 1, 1971

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By W. R. Bean

Probably few, if any, of the many serious problems confronting malleable foundries have been more difficult of solution than the question as to why malleable that is ductile, black in fracture, and normal in all respects before galvanizing should, by that process, be rendered brittle, brilliantly crystalline or "white" in fracture, and of low resistance to shock. So far as we are aware, the technical literature contains no data or discussions on this subject, except two referencesl,2 of a general character. It is apparently a question that every one concerned, producer and consumer alike, has been willing to evade as far as possible. Various theories as to the cause of the deterioration have been given but such checking of these theories as we have done indicates that there was no sound basis for most of them. This work on the galvanizing of malleable was first undertaken in 1916, and has continued until the present time. We now feel that for all practical purposes we have reached a solution and are glad to be able to offer it in a form that can be readily applied to production processes. It is impossible to give here a detailed account of the early work done on this problem. A great number of tests were instituted and an enor-

Jan 1, 1923

By George C. Branner

STATE geological surveys have had an interesting development in this country. They first appeared more than a hundred years ago. The fact that they have persisted and are now an important part of most state governments indicates the basic need for state departments con-cerned with mineral problems. The number of state surveys in 1941 (43) is at an all-time high, as is the aggre¬gate appropriation for their support for the fiscal year 1940-'41 ($1,600,708). The first surveys, those of North and South Carolina (see Fig. 1), made their appearance in 1820-'30, but neither survived that period. During the next two decades surveys were created in twenty states, but only three survived. In fact, it was not until the decade 1900-'10, when eighteen surveys were created and only five abolished, that these agencies became firmly established.

Jan 1, 1941

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By E. C. Bain, E. S. Davenport

When annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the temperatures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AF, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite? martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937

By Waynw P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps ; direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1981

By R. W. Fountain, J. Chipman

THE solubility of nitrogen in iron and steel has been of considerable interest due to the role of nitrogen in strain-aging and in quench-aging. It is generally considered that quench-aging is the result of precipitation of carbide and nitride particles from supersaturated solid solution, while strain-aging results from the segregation of carbon and nitrogen atoms to dislocations.1-9 The rate of strain-aging is controlled primarily by the amount of carbon and nitrogen in solution and the temperature. In experiments on strain-aging of pure iron with only carbon or nitrogen as impurities, Fast" has shown that even after 40 hr at 50°C carbon did not give any strain-aging while

Jan 1, 1959

By Virgil Kirkham

NORTH AMERICA has for many years led the world in phosphate production, but with development of African deposits and their marketing conditions with respect to European countries, this leadership will shortly pass to Africa. Algeria, Egypt, Tunis, and Morocco have large phosphate reserves and a correspondingly large production because of easy mining and a ready European market, which was developed during the war. An increase in home consumption is destined to develop for the eastern American fields, and the countries of the Pacific will provide a market for the western producers. New processes indicate a decrease in fertilizer costs, which will encourage a more widespread domestic use and assure better marketing conditions. The African deposits, although benefited by a water haul, have the disadvantage of being isolated from a source of acid so that the crude rock is shipped from Africa to its destination, whereas in the United States the chief product shipped is acidulated rock or various types of superphosphatic fertilizers. The principal types of phosphate deposits used in the manufacture of fertilizers are guanos, apatite, phosphatic marl, phosphatic limestone, phosphatic shale, and phosphate rock which is also known as phosphorite. Some of these deposits are found on each of the continents; Table 1 gives their occurrence, age, location, character, extent, etc. Most of , the information found in this table represents a compilation of information published elsewhere in a different form and widely scattered.

Jan 1, 1925

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947