Search Documents

By M. H. Cullender

The performance characteristics 01 gas wells producing from formations which fail to stabilize within a relatively short period of time are obscured by the interrelation of the coefficient (C) and the slope "n" of the conventional back-pressure curve q = C(P2 f- p2s)n An empirical method is presented whereby the characteristic or true slope (11) of the back-pressure curve may be determined for a particular gas well. For those gas wells which do not stabilize within a relatively short period of time, the coefficient (C) is considered as a variable with respect to time and as a constant only with respect to a specific time. Thus, the back-presrure performance of such a well is presented as a series of parallel curve5, each curve representing the performance of the well at the end of a given time interval. Through use of the method presented, a simple presture gradient is developed and maintained within the drainage area around a producing gas well during the test period in order that the variation of the coefficient (C) with respect to time does not obscure the true value of the lope. INTRODUCTION The back-pressure method of testing gas wells as set forth by Schellhardt and Rawlins1 is dependent upon the requirement that a series of flow rates and corresponding pressure data be obtained under stabilized conditions. These data arc then plotted on logarithmic coordinates of flow rate (Q) vs difference in squared pressures (P2f — P2s) in order to determine the constants (C) and (n) for Equation 1. With respect to this method of presenting the performance characteristics of a gas well, it should be pointed out that although Equation 1 is an empirical relationship, the form of the equation was justified to a considerable extent by an independent development by Muskat and Botset.2 This development was theoretical in nature; however, certain assumptions with respect to the type of flow existing (viscous vs non-viscous) were madc which may or may not be correct. As the use of the method presented by Schellhardt and Rawlins spread through the industry, it became evident that the method of testing was applicable for those wells which approached stabilized prbducing conditions within a relatively short period of time. Performance characteristics could not be determined by this method, however, for wells which approached stabilized protlucing conditions slowly over a considerable period of time. This characteristic of "slow stabilization" has generally been associated with gas wells producing frorn reservoirs of low permeability. As the demand for natural gas continued to grow through the years, a great number of wells were completed in reservoirs of low permeability which exhibited "slow stabiliz:~tion" characteristics. Consequently, the problem of determining the true performancc characteristics of these wells became more apparent. It is with this problem in mind that the isochronal performance method of determining the flow characteristics of gas wells is presented.

Jan 1, 1956

By B. E. Thompson, H. B. Fuqua

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Coolie, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor Counties is due to the influence of what is known as the Cisco arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across southwestern Wichita County into Archer County. Developments during 1938 Important discoveries in the district were considerably more numerous and of more economic importance than for several years. In addition to a number of small, relatively unimportant discoveries and to the usual local extensions to the various producing fields in the several counties, at least eight fields, most of them apparently of considerable areal extent and importance, were found. The Helmerich and Payne, Incorporated and Blackwell Oil and Gas Company No. 1 Wilson. 4 miles southeast of the town of Holliday, in north central Archer County, encountered a pay of Strawn age at a depth of 3841 to 3858 ft., and was completed for an initial production of 1952 bbl. T'his well opened a new deep pool in the K. M. A. producing zone 8 miles southeast of the K. M. A. production. Subsequently an additional deeper horizon, also of lowcr Strawn age, was discovered by wells that failed to yield commerecial oil from the horizon of the discovery well.

Jan 1, 1939

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Coolie, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor Counties is due to the influence of what is known as the Cisco arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across southwestern Wichita County into Archer County. Developments during 1938 Important discoveries in the district were considerably more numerous and of more economic importance than for several years. In addition to a number of small, relatively unimportant discoveries and to the usual local extensions to the various producing fields in the several counties, at least eight fields, most of them apparently of considerable areal extent and importance, were found. The Helmerich and Payne, Incorporated and Blackwell Oil and Gas Company No. 1 Wilson. 4 miles southeast of the town of Holliday, in north central Archer County, encountered a pay of Strawn age at a depth of 3841 to 3858 ft., and was completed for an initial production of 1952 bbl. T'his well opened a new deep pool in the K. M. A. producing zone 8 miles southeast of the K. M. A. production. Subsequently an additional deeper horizon, also of lowcr Strawn age, was discovered by wells that failed to yield commerecial oil from the horizon of the discovery well.

Jan 1, 1939

By J. Nutting, D. H. Kirkwood

IT is clearly of great metallurgical interest to know the conditions of temperature and gas composition under which different products will form in sulphide roasting. A method of graphically presenting the relevant thermodynamic data will be demonstrated, such that these conditions are readily obtainable. The products of sulphide roasting may be oxide, sulphate, or oxysulphates, and the equilibria between these may be represented in the following way: 2 MSO4 = MOMSO4 + SO3 MO-MSO4 = 2 MO + SO3

Jan 1, 1961

By J. B. Dilworth

In estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end of its life, or to return the capital involved when the earningpower of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the 'number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compouiid interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given length of time. In most practical cases the interest is compounded and the fresh amount added at the same time—usually once a year—and on this basis the problem may be solved as follows : Let S = total amount to be retired, Let T = interest rate : R = 1 + r, Let n = life of tlie sinking-fund or the amortization-period, Let L = the sum set aside at the end of each year. Then the amouilt of the sinking-fund at the end of first year is 2, which at the end of n years will have illcreased by compound interest to IRn-l. Similarly, another amount, x, will be set aside at the end of second year, which will in turn increase

Jan 1, 1911

By Nelson B. Russell, Donald C. Bond

The effects of various antifreeze agents on the formation of hydrogen sulphide hydrate have been studied. On a molar basis the relative lowering of Tm (the maximum temperature at which solid hydrogen sulphide hydrate can exist in equilibrium with the given solution) for the various agents is: sodium chloride 1.00, calcium chloride 1.71, methyl alcohol 0.57, ethyl alcohol 0.68, ethylene glycol 0.73, diethylene glycol 0.73, sucrose 0.87, dextrose 0.71. On a weight basis the relative lowering of TM is: sodium chloride 1.00, calcium chloride 0.91, methyl alcohol 1.08, ethyl alcohol 0.89, ethylene glycol 0.69, diethylene glycol 0.41, dextrose 0.23, and sucrose 0.15. Introduction The solid hydrate of hydrogen sulphide, H2S.6H20,1 is in equilibrium with water and liquid hydrogen sulphide at 85°F at a partial pressure of hydrogen sulphide approximately equal to the vapor pressure Of hydrogen sulphide at that temperature. At temperatures below 85°F, in the presence Of excess hydrogen sulphide (greater than the amount required to react with the water present) the hydrate is in equilibrium with liquid hydrogen sulphide at approximately the vapor pressure Of hydrogen sulphide. In the presence of excess water, the solid hydrate is in equilibrium with liquid water, containing dissolved hydrogen sulphide, at a pressure lower than the vapor pressure of liquid hydrogen sulphide at the same temperat~re.2 The lower the temperature, the greater the difference between the decomposition pressure of the hydrate and the vapor pressure of liquid hydrogen sulphide at that temperature. Conditions conducive to the formation of solid hydrogen sulphide hydrate may exist in wells producing a gas containing a high percentage of hydrogen sulphide under high pressure, or in the lead lines from such wells. This paper gives the results of tests made with various antifreeze agents which might be useful in decomposing the hydrate or in preventing the formation of the hydrate of hydrogen sulphide Apparatus Fig , shows a diagram of the apparatus used. The sample under observation was contained in a glass tube 34 cm long, having a 6 mm id and a wall thickness of 2.5 mm. The lower end of this tube was closed- with a plug of butyl rubber. The upper end of the tube was connected to a diaphragm gauge, with a stainless steel diaphragm, a manometer, a vacuum pump, and a cylinder of hydrogen sulphide, The tube was held nearly horizontal, with the liquid resting along the lower side of the tube. It was found that when the tube was held in a vertical position, it broke with ex. plosive violence as soon as it became filled with solid hydrate. Presumably this was caused by the expansion which occurred on solidification of the hydrate. The difficulty disappeared when the tube was held in an inclined position during the tests.

Jan 1, 1949

ZAY JEFFRIES, who has been awarded the Douglas medal, established in 1922 by a group of the friends of the late James Douglas for distin-guished achievement in non-ferrous metallurgy, is one of the most notable graduates of the South Dakota School of Mines where he took his B. S. degree in 1910. The following year he was manager of the Ideal Mining Co., at Custer, and in 1911 he became instructor in metallurgy at the Case School of Applied Science, Cleve-land, where he remained until 1917, and in 1918 he took his D. Sc. degree at Harvard. During all this period he was engaged in experi-mental and consulting work for the Electric Railway Improvement Co., t h e Cleveland Steel Tool Co., the W. S. Tyler Co., the Lincoln Electric Co., the Aluminum Castings Co., and the Cleveland wire di-vision of the General Elec-tric Co. He is now en-gaged in general consulting work, especially for the Aluminum Co. of America, the General Electric Co., and the National Tube Co. He has contributed to the Transactions papers on the determination of grain size in metals (with A. H. Kline and E. B. Zimmer) LIV, 594; grain growth phenomena in metals, LVI, 571; the tungsten-molyb-denum equilibrium diagram and system of crystalliza-tion, LVI, 600; grain size inheritance in iron and carbon steel, LVIII, - 669; effect of temperature, de-formation and grain size on the mechanical properties of metals, LX, 474; metallography of tungsten, LX, 588; physical changes in iron and steel below the thermal critical range, LXIII, and LXVII, 56; and the trend in the science of metals, LXX, 303. In addition to participating freely in the discussion of other papers before the Institute he has found time to contribute notable papers to the Institute of Metals (Great Brit-ain), the principal technical journals, and to write a book on "The Science of Metals" in collaboration with R. S. Archer.

Jan 2, 1927

Through the generosity of Sir Robert Hadfield, Honorary Member, the Directors of the American Institute of Mining Engineers are enabled to announce the Hadfield Research Prize of $1,000 for the best contribution to the publications of the Institute upon the general subject of The Different Forms and Combinations of Carbon with Iron, including those in Iron Alloys. The prize will be awarded at the Annual Meeting of the Institute in February, 1916, to the best paper upon this subject which is presented to the Institute before Nov. 1, 1915, provided such paper is deemed worthy by the Institute's Iron and Steel Committee. The following suggestions are also added for the guidance of those who may take part in this research. While' it is not desired to define closely the exact lines or scope of the proposed research, as it is advisable to make these as broad as possible, the object in mind maybe said to be generally as follows: To elaborate and find out the best methods of determining the forms of carbon in steel or iron, including those in iron alloys. A portion of the work would probably be a continuation of the researches which have in the past been carried out by Jullien, Abel, Muller, Ledebur, T. Sterry Hunt, Akerman, Arnold, Stead, E. D. Campbell, Hogg, Parry, Upton, and others. In a generic way, metallurgists now speak of carbides, sub-carbides, double carbides, special carbides, and other combinations. It is very desirable that these should be accurately defined and understood. It is also desirable to know whether there are other or new forms; if so, can these be separated and their characteristics obtained. It may be interesting to point out that the carbon compounds now definitely known are stated to number over 80,000. It is very probable, therefore, that there is room for much valuable and useful research to be carried out with the object of increasing our knowledge of the various combinations of carbon with iron, as probably some of these are still unknown

Jan 5, 1914

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.' Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer' and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

By B. G. Bunting, D. L. Abata, J. Robb, J. H. Johnson

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during mining operations. The explosives included two semi-gelatin dynamites, three slurry explosives, and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and toxic gases produced by the detonation were trapped at the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/1bm): NO, 0.0100-0.035; N02, 0.003-0.019; CO, 0.08-0.30; SO2, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1983

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

The Hurghada field is still the major producing field in Egypt. There was almost no activity in the Abu Durba field during 1936 and no new evidence is available. The following table summarizes the information on the Hurghada field for the year 1936. Hurghada Field Age of field to end of 1936, years.................... 23 Producing area for gas and oil, acres................. 1,050 Barbels Total oil production to end of 1936.................. 29,046,572 Total oil production during 1935.................... 1,212,182 Total oil production during 1936.................... 1,218,708 Daily average during November, 1936............... 3,249 MillionB CU. Ft. Total gas production (Aug. 1925 to end of 1936)...... 3,966 Total gas production during 1935................... 278 Total gas production during 1936................... 280 Maximum daily in 1936............................ 0.9 Number of producing wells completed to end of 1936... 94 Number of producing wells completed during 1936. ... 3 Number of wells abandoned during 1936............. 3 Producing wells at end of 1936...................... 768 Average depth of bottom of producing wells, ft....... 1,720 Average depth of top of producing horizon, ft......... 1,598 Character of oil, approx. average during 1936: Gravity at 60&apos; F., 0.900; base mixed. Character of gas, approx. average during 1936: gallons gasoline per 1,000 CU. ft., 6.2. Producing rock (main): Nubian sands, Cretaceous; character, sand rock and sandy shales. 1 The figures given by the author were in tons. A conversion factor of 6.98. based on 0.900 sp. gr., was used to obtain the number of barrels.—Ed. 2 All pumping.

Jan 1, 1937

By N. Albon, J. F. Miller, R. W. Coutant

The deposition of nickel from nickel carbonyl onto amorphous substrates has been studied, with attention being paid to the specific effects of the physical and chemical nature of the substrate and to the effect of oxygen on the crystal morphology. With substrates having microscratches or etch lines, nu-cleation was observed to occur preferentially at these surface features. Flame polishing of the substrate surfaces was found to remove any regularity in preferred nucleation sites. Nucleation was observed to occur less readily on substrates having relatively low surface energies, e.g., Teflon and carbon, than on materials having relatively high surface energies such as fused silica. At low oxygen concentrations [Ni(CO)4/O2 > 54 x 1031, apparently pure and well-formed nickel crystals were observed to nucleate and grow irrespective of the presence of oxygen. At higher concentrations of oxygen, a secondary growth process, dependent upon oxygen concentration and resulting in a gradual change in crystal morphology, was observed. It is concluded that the influence of oxygen on the nucleation and growth of nickel is determined by the relative kinetics of the various possible reactions, and that under the experimental conditions employed the 0-Ni interaction occurs at some nucleation or prenuclea-tion stage. THE purpose of the research on crystal nucleation in chemical vapor deposition as described in this paper has been twofold: 1) to examine some effects arising from the use of amorphous substrates, and 2) to study the specific effects of oxygen on the nucleation and growth of nickel in a nickel carbonyl-carbon monoxide system. The nickel-nickel carbonyl system was chosen for study for several reasons: 1) nickel films are of potential interest in electronic technology, and 2) the deposition can be carried out at moderate temperatures, thus making possible detailed study of the processes occurring and the use of a variety of substrate materials (including some which melt at relatively low temperatures). Fairly well-characterized chemical kinetics and a broad background of information are available on the py-rolysis reactions and on the mechanisms of Ni-O interactions. NUCLEATION AND GROWTH THEORY The theoretical background for the analysis of nucleation and growth by vapor deposition for a one-component system (physical vapor deposition) and the problems encountered therein have been reviewed by Hirth and pound.&apos; More recently Mande12 has indicated the difficulties of applying such theory to chemical systems. One of the major problems involved is the possible multiplicity of chemical reactions and deposition routes. For example, those reactions which are probably of significance in a discussion of the pyrolytic deposition of nickel from nickel carbonyl under the conditions of the present experimental work are illustrated in Fig. 1. As is true with most cases of chemical deposition, many of the quantitative data necessary for a complete analysis of the system are either not available or not directly measurable. However, with the present system, sufficient data are available for a discussion of nucleation and growth on a qualitative basis. Classically, the rate of nucleation of a monatomic species being deposited from a vapor phase is given by

Jan 1, 1965

By Fathi Habashi

Chalcopyrite can be readily leached with HNO3, but the recovery of elemental sulfur does not exceed 50% under the most favorable conditions. Preheating at 500°C in a slightly reducing atmosphere increases the recovery of elemental sulfur to about 65%. Chalcopyrite can also be treated with HNO3 in a pressure reactor at 110°C to solubilize selectively the copper while iron remains in the residue as an oxide. The recovery of elemental sulfur also improved when preheated chalcopyrite is treated in this way. Stainless steel should be an adequate material of construction.

Jan 1, 1974

THE following employment items are made available to AIME on a non-profit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnswarth Ave., Detroit; 57 Past St., San-Francisco; 84 E. Randalph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York Office and include 6c in stamps far forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available far $3.50 a quarter, $12 a year. MEN AVAILABLE Graduate Mining Engineer, 38; married, two children, Dutch nationality. Experience bauxite open-pit dragline, stripping and mining, nickel silicateous ore exploration, tin lode mining and dredging, ore dressing research, administrative. work, all in responsible positions. Read, write and/or speak seven languages. Desires responsible position. Presently located Netherlands. M-655. Mining Geologist, 35, married, 3 children, Canadian citizen. Eight years&apos; experience Canadian gold mines as geologist, chief engineer, shift boss, 3 years in western U. S. as surveyor, junior geologist, etc. Desires position of responsibility. Prefer western United States. M-656-478-E-3-San Francisco. Mining Engineer, 30 years&apos; experience open-pit and underground coal and iron mines. Held positions engineer to manager. Desire position of responsibility in foreign field. M-659.

Jan 1, 1952

By Eric Sinkinson

MANY of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in-serpen-tine masses, somewhat decomposed, and in mining it wall rock is inci-dentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumna, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18° C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact; MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18° C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H20) or (4MgCO3.Mg(OH)25H20), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1936

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. &apos;.:&apos; It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.&apos; The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By S. Stopek, E. D. Hinkley, R. H. Rediker

Epitaxial heterojunctions have been prepared by melting the lower -melting-point semiconductor of the interface between two dijferent semiconductors. when the temperature is reduced, the melted material recrystallizes, having alloyed into the higher -melting-point semiconditctor. The electrical and elcctro-optical properties of such single-crystal heterojunctions between GaAs and Gash and between p-type InAs and n-type Gash are the subject of this paper. The forward current varies as exp (AV), where A is substantially independent of temperatuve. For Gds-Gash heterojunctions at temperatures above, 370°K, if the current-voltage relationship were to he expressed as exp (qV/nkT), then n would he less than unity. The injection luminescence associated with forward current is, for the most part, characteristic. of the lower bandgap semicondutctor. These results can he explained by carrier injection into the lower bandgap semiconductor by tunneling through a barrier at the interface. The photovoltaic effect measured for incident photons having energies in the range between the bandgaps of the two semiconductors is much smaller than that produced by higher-energy photon The smallness of this between -the-gap photovoltaic response can he explained by the low probability for penetration of the barrier by the carriers produced in the smaller -bandgap semiconductor. THE technique of interface alloying has been used to produce single-crystal junctions between dissimilar semiconductors.&apos; Oriented wafers are placed on a carbon heater strip, Fig. 1. so that semiconductor S1, which has the lower melting point, is supported by semiconductor S2. Electrical current passed through the heater strip produces a temperature gradient such that S2 is at a higher temperature than S1. As the temperature is raised the lower face of S1 begins to melt. Before the entire wafer can melt, however, the heater-strip current is turned off and, as illustrated in Fig. l. the melted portion recrystallizes, having alloyed into S2. Junctions have been fabricated by the above procedure between GaAs and germanium, between GaAs and GaSb, and between InAs and GaSb. Mroczkowski, Lavine. and Gatos have described the metallurgical and chemical aspects of the GaAs-Ge junction.2 The transition from GaAs to germanium is not monotonic and a portion of the recrystallized region consists of the GaAs-Ge eutectic. Since gallium is an acceptor and arsenic is a donor in germanium, since germanium dopes GaAs, and since the electrical properties of the GaAs-Ge eutectic have not been investigated, any interpretation of the electrical characteristics in terms of simple heterojunction theory would be incorrect. That the rectification of GaAs-Ge heterojunctions is not a property of the impurity doping of the GaAs or the germanium, but is most probably due to the impurity distribution in the recrystallized region, is clear from the fact that forward conduction occurred for all the GaAs-Ge interface-alloy junctions (whether they be n-n,n-p. p-n. or p-p) when the germanium was biased positively. The electrical characteristics of these GaAs-Ge heterojunctions will not be discussed further in this paper. Electron-beam microprobe analysis of GaAs-GaSb heterojunctions showed that the transition from arsenic to antimony atoms was without structure. and that the transition occurred within a 2 to 3 region.&apos; In this paper we will describe the electrical properties of the GaAs-GaSb heterojunctions as well as electrical and electro-optical properties of the InAs-GaSb heterojunctions. A band model for the junction will be proposed which can explain these properties. ELECTRICAL PROPERTIES OF GaAs-GaSb HETEROJUNCTIONS After interface alloying. in preparation for the electrical and electro-optical experiments, ohmic contacts were made by conventional means. For example. Kovar tabs clad with tin were alloyed to n-GaAs or similar tabs clad with Au-Zn were alloyed to p-GaAs. The units were mounted and then etched. All four combinations of conductivity types

Jan 1, 1965

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939