Search Documents

By James W. Burns

Thin, heavily doped n-type layers of GaSb have been grown on p-type GaSb substrates. Techniques have been developed for the growth of the n-type layers from a tellurium-doped gallium-rich solution. The solution used consists of 95 at. pct Ga and 5 at. pct Sb. The process consists of immersing the p-type wafer in the solution at a temperature slightly above the liquidus temperature, holding briefly to permit dissolution of the substrate surface, then decreasing the temperature to a value slightly below the liquidus to obtain 1 HE resistivity of n-type GaSb varies linearly with applied hydrostatic pressure, while the resistivity of p-type GaSb is insensitive to such pressure.1,2 The growth. Growth from a solution of GaSb in tin will also be described. In either case the substrate is clamped to a shelf at one end of a graphite boat, and immersion of the wafer and subsequent decanting of the solution is accomplished simply by tilting the furnace. The process is useful for the formation of p-n junctions in III-V compounds and has the advantage that the problems normally associated with diffusion of Group VI elements are not present. Layers up to 4.0 mils in thickness have been grown by the process. material therefore should be useful in a hydrostatic pressure-sensing device. A practical hydrostatic pressure sensor, however, requires the fabrication of GaSb sensing elements of several hundred ohms resistance. Attempts were made to prepare such elements by diffusion, taking advantage of the high sheet resistance of the thin diffused layers and depending upon the p-n junction to provide isolation from the base layer. Additionally, thin layers of conductivity type opposite from that of the base layer were pre-

Jan 1, 1969

By J. A. Musselman, J. B. Cheatham

In recent years considerable effort has been expended in the search for new ways of drilling into the earth's crust and for improvements of existing methods. A number of novel techniques have been explored such as explosive, flame, electric arc, abrasive jet, chemical, and various percussion-type dri1ls.l Some of the new methods are useful in isolated situations, but rotary drilling continues to be the most versatile and generally economical method for rock drilling. An understanding of rock failure during drilling can lead to improved rotary drilling techniques and to the development of new methods. Experiments 2-4 have shown that rock strength and ductility increase with increasing pressure; therefore, meaningful experimental investigations should be carried out under conditions similar to those encountered at the depths to which oil wells are drilled. The action of a roller-cone bit is not pure rolling in all cases but frequently involves gouging and scraping action. However, vertical penetration of a horizontal rock surface by a single punch has served as a first approximation of the rock/bit tooth interaction during drilling.5,6 In these experiments semi-infinite smooth rock surfaces are indented by steel tools with configurations having various degrees of dullness. Both static and dynamic tests have been investigated; however, static loading provides a good approximation of the loading rates occurring during rotary drilling. As a more realistic approximation to actual drilling conditions, chip generation must also be considered. Recently, studies have been made of indexing or chipping from a bit tooth to a previously formed crater.7-9 The purpose of the present investigation is to study indexed penetrations in greater detail. Fig. 1-A illustrates the general problem. Pittman and Cheatham 10,11 have used plastic limit analysis to study the idealized plane-strain indexing problem for a material having a linear Coulomb-

Jan 1, 1972

By K. Thirumalai

Although the term "spalling" has long been known, Norton l first referred to its usage for the fracture or disintegration of materials subjected to rapid temperature changes. Spalling of ceramic materials at high temperatures has received attention in the past.2-4 Removal of the char formed during ablation in reentry of space vehicles has been referred to as mechanical spalling.5 The first experiments to evaluate the process of rock fragmentation by thermal spalling were conducted by Stoces6 using a series of gasoline burners on the quartz veins of the Zinnwald deep mines in Germany. After the development of rocket-jet burners, the principles of thermal spalling combined with high fluid momentum found wide practical application in rocks. The well-known jet piercing process for drilling blastholes in taconite and for jet channeling in the quarrying of granite are among the more notable of these application.7 For the purposes of this study, thermal spalling or spallation of rocks is defined as progressive failure caused by thermal stresses induced by a sudden application of heat from a high temperature heat source. Gray observes that the size of the spall is dependent on the pattern of induced thermal stresses before failure. The spallability or the relative susceptibility of rocks to failure by thermal spalling is a complex but potentially useful parameter for qualitative comparisons. Fundamental differences exist in the degree of spallability among different types of rocks. Accurate prediction of spallability of any particular rock has so far not been possible. Measurement of the state of stress and temperature in the rock during the rapid thermal spalling process poses difficult problems that must be solved. Identifying the parameters that influence the thermal spalling proc-

Jan 1, 1970

By Oscar A. Glaeser

The purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings. Need for Ventilation The range between the maximum oxygen content of normal air and the minimum safe content is extremely narrow, approximately 5 per cent. Furthermore, normal air must not be contaminated with irrespirable gases beyond definite limits, and mineral dusts are equally dangerous, although health impairment is slower. Tables 1 and 2 present the more common respiratory hazards encountered in mines. Adequate ventilation is the most effective means available to reduce or eliminate these hazards. Mechanical ventilation has reached varying stages of perfection in coal mines and in many large metal mines. The small mines and prospects rarely have a definite plan of ventilation. As a consequence underground workers are frequently exposed to health and accident hazards. The annual reports of fatalities in mines in the Western States record yearly many deaths due to asphyxiation and deaths caused by men falling down shafts and raises after being overcome by gas. At times mining operations are slowed up because there is no means of driving out the gas after blasting. For that reason only one shift is worked, or men wait from one to several hours for the "smoke" to clear out. Methane gas in varying quantities is widely distributed throughout California. It has been encountered in explosive concentrations in the coast range. It has been found on the Mother Lode and in quicksilver mines near the coast. Methane explosions have not been uncommon in underground operations and in tunneling jobs. These conditions and records indicate that there is room for improvement in mine-air conditions.

Jan 1, 1937

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, -1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2 CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws .in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were. tested for air circulation and air tightness and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering .these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

ONE of the interesting-though not unnatural-features of the whole Porphyry Copper development is the way in which the history of each property dovetails with that of one or more of the others. The same names keep cropping up as one digs into the accounts of events from 1900 to 1915. J. Parke Channing made examinations of Nevada, Ray, and Inspiration, as well as of Miami. Henry Krumb did important work in the early stages of the exploitation of Utah, Nevada, Ray, Braden, and Inspiration. Pope Yeatman was favorably impressed with the Braden property before he had ever visited it, when he saw a batch of Braden ore sent to the United States for testing. It reminded him immediately of Nevada Consolidated ore: indeed, he was unwilling at first to believe that it came from South America. And it was while working on the examination at Utah Copper that Philip Wiseman became enthused with the possibilities of the Ray mines. In 1905, Mr. Krumb, under the general direction of A. Chester Beatty, was strenuously engaged at Bingham, Utah, in arriving at an answer to this question: Should or should not the Guggenheim interests back Jackling to the tune of several million dollars to build the big concentrators at Gafield? Seeley W. Mudd was the Guggenheim engineer on the Pacific coast and in that capacity was indirectly responsible for the work at Bingham. At his suggestion Wiseman came up from Los Angeles as one of Krumb's assistants-at $5 per day, incidentally. A little later Mr. Mudd, in Utah on one of his visits, went down to Bingham. That evening in the old Hills Hotel in Markham Gulch he was going over reports with Mr. Krumb. Wiseman and some of the other engineers on Krumb's staff were present. During a breathing spell, Mudd expressed

Jan 1, 1933

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By Clarence Zener

Theoretical considerations by one of the authors have ledl to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have verified2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are presented to test this extended theory. The physical basis for the type of internal friction that is being investigated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so likewise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal currents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,³ and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal currents accompanying transverse vibrations. Of more fundamental importance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adjacent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

By J. W. Spretnak, G. W. King

THE crystallography and morphology of 0-Al,Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 p. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly All13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (00l)? || (110)Al [100]? || [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By Darrel W. Hansen

Morrow Point Dam and Power Plant are principal features of the Bureau of Reclamation's Curecanti Unit of the Colorado River Storage Project. They are under construction on the Gunnison River 20 miles east of Montrose, Colo. Johnson-MK is the prime contractor, and represents a joint venture of Al Johnson Construction Co., Minneapolis, Minn., and Morrison-Knudsen Co., Inc., Boise, Idaho. The power plant will be housed in an underground chamber in the left abutment, approximately 250 ft behind the original canyon wall. The chamber is 206 ft long and 57 ft wide. The distance from the foundation to the spring line of the roof arch varies from 51 ft in the service bay to 120 ft in the control bay. The roof arch has a rise of 16 ft. The longitudinal center line of the chamber is orientated east-west with the draft tubes discharging nearly due north. Access to the power plant chamber was possible through the cable tunnel, access tunnel, two draft tube tunnels, two penstock tunnels, exploratory tunnel, which became the ventilation tunnel, or the grouting and drainage tunnel leading to the dam. (See Fig. 1.) The shortest and fastest access was through the cable and access tunnels, and the contractor drove these two tunnels simultaneously. The cable tunnel and cable gallery excavation exposed a transverse section, at the west end of the chamber, that was 15 ft wide and extended from the crown to 5 ft below spring line. It was here that arch excavation began. The first 34 ft of advance along the arch was driven on three headings, and the muck was removed through the cable tunnel. Meanwhile, the access tunnel was completed, and a raise was driven from its crown to intersect the advancing arch excavation near the longitudinal centerline

Jan 1, 1968

By George Smith

IN the utilization of natural resources owner, operator, and consumer should share the attendant benefits. Development needs to be planned under terms recognizing fully the interests of all concerned, for any undue advantage given to any one of these participants is apt to involve even greater and disproportionate injury to one or both of the others. For this reason it is well to preface any consideration of needed reforms in legislation affecting the disposition of public land with a survey of certain fundamental principles that determine the general conditions of all land transfers preliminary to development, utilization, and production. The disposition of any undeveloped natural resource, whether timber, oil, coal, or water power, as a transaction to which hand owner and prospective developer are parties, must be based in theory upon a division of expected returns. Whatever the terms of such disposition, neither party can reasonably ask for anything other than an equitable division of the returns. Under this analysis three and only three questions need to be discussed ; namely, what are those profits, how is this division to be accomplished, and what is the equitable basis of division ? The answer to the third question should probably be found by applying to the problem the principles of theoretical sociology, and' the question need not be mentioned further at this time, inasmuch as it does not involve the practical considerations to be kept in mind in connection with the other questions, which are concerned with only the measure of returns and their division. That is to say, whether the land owner's equity is to be stated as 95 per cent. or as 5 per cent. of the profits attending the development of the particular resource, no change would be necessary in the method to be adopted of arriving at the closest approximation of the prospective total profit.

Jan 10, 1913

By John Park

THE mining .district is located in the northeasterly part of Nevada, between the Jarbidge River on the west and the East Fork of the Jarbidge on the east. The northern boundary of the district is but a few miles south of the Idaho state line-the gold-bearing area extending from this point south, for 5 or 6 miles. The Jarbidge Mountains, in which the ore deposits occur, range from 5000 to 11,000 ft. in elevation, the most important mines being situated about 7000 ft. or higher. The town of Jarbidge lies along the Jarbidge River and is reached by stage from Rogerson, Ida., the nearest railroad point. During the summer months, the camp may be entered from the south by way of Deeth, Nev., but no regular transportation facilities are available over this route. HISTORY The mineral deposits were not discovered until 1909, when D. A. Bourne, panning along the river bank, found gold in the gravel at the mouth of a small stream flowing into the Jarbidge. He prospected in the vicinity of this stream, later known as Bourne Gulch, and shortly after located the North Star claims. During the following spring and summer (1910), the camp of Jarbidge grew from nothing to a town of 2000 people and the hills surrounding it were practically all taken up by mining claims. Most of the work done during. the first year or two consisted of trenching and open-cut prospecting. Tunneling was started on a number of claims and many veins were uncovered. Mills were built and operated on a few properties, notably the Pavlak and the North Star. These ran only a few months, however, when they were closed down because of extraction and financial difficulties.

Jan 1, 1925

By W. E. Mitchell

ELECTROLYTIC, production of cadmium at the Great Falls plant started in the first part of the year 1925. Prior to that time, an experi¬mental unit had been in operation for a few months during the year . 1922. At present the plant is the largest producer of cadmium, not only in the United States but in the world. Electrolytic cadmium is characterized by its very low content of impurities. The main impurities, which are lead, copper, zinc, and iron, do not aggregate more than 0.05 per cent., leaving a cadmium content better than 99.95 per cent. The consumption of cadmium has increased rapidly since the war, with the growing use in the plating industry. Cadmium plating has come into prominence because of its connection with the automobile and radio industries. As a protective coating, a deposit of, cadmium is superior to zinc. Cadmium is also used extensively in alloys. Important among these is the alloy with copper used in telephone and trolley wire. In proportion of 0.5 to 1.2 per cent., cadmium adds materially to the strength and wearing qualities. Practically all commercial zinc concentrates contain a small amount of cadmium. In the electrolytic zinc process, the cadmium that is dissolved in the regular leaching operation is removed from solution with metallic zinc, generally added in the form of zinc dust. This precipitate also contains the copper taken into solution and the excess of zinc dust, which is required in order to insure a complete removal of all impurities. The precipitate is treated by a separate process to recover the copper, cadmium and excess zinc. In order to make the metals more soluble and to render insoluble such impurities as iron, arsenic and antimony, the precipitate is roasted. The roasting is carried out in gas-fired McDougall furnaces, with a roasting temperature of about 700° C.

Jan 1, 1930

By J. Szekely

The paper discusses simultaneous heat conduction and diffusion. These problems may arise in slag-metal kinetics and in connection with rapid heating or cooling of specimens. A mathematical formulation is given and it is shown that the transients due to either the variability of the diffusion coefficient with temperature, or thermal diffusion, are unlikely to be important for molten or solid metals and slags. The negligibility of these effects is due to the large values of the ratio thermal diffu-sivity/molecular diffusivity. In many problems relating to transport-controlled metallurgical kinetics the diffusion process is accompanied by the transfer of heat; large-scale metal refining or metal reduction may be quoted as examples. It has been shown that due to turbulent mixing in these systems the relevant transport phe- nomena are best described in terms of "surface renewal models" which require the solution of the unsteady-state diffusion equation.1-1 Problems involving simultaneous diffusion and heat conduction are also encountered in the laboratory in connection with rapid heating or cooling of specimens. The effect of variable temperature on diffusion may be twofold: a) in the absence of "cross effects" the problem, due to variable temperature, is that of diffusion with a variable diffusion coefficient; b) if the Soret Effect is nonzero, thermal diffusion must also be taken into account in the formulation. Although information is available on thermal-diffusion transients in a steady-temperature gradient,4'5 little work has been done on the effect of unsteady temperatures on either the diffusion coefficient or on thermal diffusion.' In the following a formulation is given and solutions presented with a view of examining the areas where these effects may be important.

Jan 1, 1965

By Brigitta Hassler

INTRODUCTION In the early 1960's research was begun in Sweden to improve the agglomeration of our domestic iron ore concentrates (5). Different agglomeration methods that were used in the building material industry were studied under the economic support from the Swedish Technical Council, the Swedish Board of Technical Development and by the Swedish industry. The research work was performed at the Division of Mineral Processing at the Royal Institute of Technology in Stockholm. All known agglomeration methods were reviewed and the methods were developed to produce superior quality agglomerates (6). The term cold bonding (in contrast to sintering) was introduced to describe the induration operation in these processes and this has been accepted internationally. Even though we used it mostly for steam autoclaving methods, it has come to describe a class of processes that use binding methods by pore filling. Schumacher in Germany discovered around 1907 that a strong material can be produced by mixing slaked lime with fine ground quartz and subjecting to a steam atmosphere under pressure at about 185ºC. This started development of lime-sandstone building materials and later on, in Sweden, the light-weight concrete. Schumacher also used the same reaction for briquetting iron ore concentrates by adding silica and lime, and autoclaving. The product seems to have been accepted for blast furnace burden and the process was used on an industrial scale until the 1920's. The sintering method has a small melting phase as diffusion medium and in the steam-autoclaving method a small quantity of water condensate at about 200°C serves the same purpose. Thus the induration process by the hydrothermal hardening methods is similar to that of sintering or heat treatment.

Jan 1, 1977

By Samuel G. Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change. Outline of Kennecott Mines Geology The mines at Kennecott are on the northeast flank of a broad anticlinell where erosion has exposed the Upper Triassic Chitistone limestone resting conformably on the Permian or Triassic Nikolai greenstone.2 These two are the only formations exposed in the immediate vicinity of the mines that bear relation to the ore deposits. The Nikolai greenstone is a series of altered basaltic lava flows, the actual thickness of which is unknown. The Chitistone limestone is the ore-bearing formation. At its base is a bed of about 5 ft. of red, green, or black shale which shows strong evidence of movement wherever it is exposed underground—one of the

Jan 1, 1929

An "international gold conference" was held at Spokane, Wash., on Sept. 5, 1918, under the auspices of the Northwest Mining Association, which was attended by a large number of engineers, mine operators, and bankers, representing the northwestern states, as well as Alaska and British Columbia. The principal subject under consideration was the doleful condition of the gold-mining industry, gripped between the diminished purchasing value of its product, and the increased cost of its operation. Two resolutions were adopted by the meeting. The first approved the resolution adopted Aug. 12 by the American Gold Conference, a permanent organization formed at Reno, Nev., in which it is stated that relief by the United States to the gold producers of this country should he made to correspond with the increased cost of production, the extent of the relief to be fixed from time to time to Meet changing conditions. The second resolution, adopted after serious and long-continued discussion, was introduced by F. A. Ross, mining engineer, of Spokane, and a member of the Institute, and was as follows: WHEREAS, it is now clearly understood and agreed by the allied nations that national gold reserves must be augmented without delay if rapidly expanding credits are to be secured; and WHEREAS, at this time, the production of gold is daily decreasing to an alarming extent because of well known conditions that, render the mining of gold-bearing ores unprofitable; and WHEREAS there is no way by which the mining of gold-bearing ores may be made profitable except by the direct' aid and influence of the government; and WHEREAS the government has appealed to the mining industry for practical information and practicable suggestions upon this subject; therefore, be it

Jan 10, 1918

By Dwain K. Butler

INTRODUCTION Characterization of a site for the prediction and simulation of dynamic events requires the determination of mechanical properties of the rock at stress/strain levels and rates and at a scale appropriate for the events and critical structures involved. The structures of interest can be on the surface, underground, or designed to impact and penetrate into the site (projectiles). Dynamic events of interest are equally diverse: seismic waves from distance earthquakes or explosions; close-in phenomena associated with earthquakes and explosions; vibrations associated with heavy equipment or machinery; and stress transients associated with impact and penetration. The complexity of site characterization depends on two factors not specifically related to the nature of the site itself: the stress levels generated by the dynamic event and the sophistication of the prediction and simulation techniques. For very high stress levels, such as occur near a nuclear detonation, and for low stress levels, such as occur during seismic wave propagation, site characterization is simplified, and often certain details of the site are not particularly important, such as shear strength variations in the case of very high stress levels. In the intermediate stress range, however, all descriptive relations are non- linear, a complete finite strain constitutive model is required, and all details of the site, such as lithology and fracture distribution, become important. The site characterization must be complete enough to support the most sophisticated prediction and simulation technique that will be applied to the analysis of the dynamic event. The procedures of site characterization are illustrated in this paper by a specific dynamic event, projectile impact and penetration, and a specific site, an outcrop of Dakota Sandstone near San Ysidro, New Mexico. The structure of interest was the projectile itself: nominally, 1.5 m in length, 0.165 m in diameter, 180 kg

Jan 1, 1984

By George Smith

ChillaQoe is situated in latitude 17" S., about 138 miles from the port of Cairns, with which it is now connected by rail. A township has been established on the banks of Chillagoe creek, a perennial stream of irregular volume crossing the field almost at rightrangles, nearly midway between the mining-camps of Calcifer and Mungana, which have been formed at the southeastern and western extremes of the field respectively. This situation was selected because of the water-supply and its proximity to the site most suitable for the erection of reductionworks. By its central position it commands the whole of the mines. The altitude above sea-level is about 1200 ft., whereas that of Calcifer and Mungana is 1400 ft.—a difference sufficient to account for a materially higher temperature at Chillagoe. The surrounding limestone bluffis add by radiation to the heat, and, at the same time, prevent the cool breezes from passing freely through the town; consequently, the temper* ture, which is high throughout the year, and especially so during the summer months, is here ge~ierally very oppressive also. The general trend of the field is southeast and northwest, and its length about 18 miles, with an average width of 5 miles; the approximate area is thus 90 sq. miles. The surrounding mineral-district is, however, much more extensive, and numerous other mines, sprcad over wide areas and producing a variety of minerals, exist in the same or parallel belts of mineralized country, of which Chillagoe proper covers but a very small portion. Immense bluffs of limestone, wollastonite and conglomerate, rising in places to nearly 300 ft., and so~netimes nearly a quarter-mile across, give the field a very picturesque and interesting appearance. The limestone has been classified as Devo-

Jan 1, 1904

By Milnor Roberts

The Nicola Valley coal-field is small, but it seems likely to become important because of its commanding position in a rich region that is developing rapidly. Bituminous coking-coal in workable quantity has not been found at any other point between the Crow's Nest Pass region, about 400 miles to the east, and Vancouver island, 250 miles westward. The Canadian Pacific railway reached the Nicola valley two years ago ; two other lines, the Canadian Northern and the Great Northern, are building towards the valley. The vast region between the Rocky mountains and the Pacific coast, extending northward for several hundred miles from the international boundary, which has been the scene of extensive mining- and smelting-operations for many years, is filling up with settlers, who are attracted by the wealth of minerals and timber, the rich soil of the valleys, and the fine climate. The Nicola river, flowing westward through the valley of that name in the Yale district, discharges into the Thompson river, which is the eastern branch of the Fraser. The transcontinental line of the Canadian Pacific railway crosses the mouth of the Nicola river at Spence's bridge, 178 miles from Vancouver. From Spence's bridge the Nicola branch line ascends the valley for 40 miles to Merritt, the coal-center, and continues 7 miles farther to the town of Nicola. Thus the haul from the mines at an elevatioiz of 2,000 ft. to salt water is 218 miles down river-grades. The Nicola branch will be continued about 150 miles farther eastward to Penticton, where it will connect with an extension of the line through the rich Kootenay and Boundary districts. The Canadian government has granted a subsidy of $6,000 per mile, to which the provincial government is planning to add $5,000 per mile, to assist in the construction of the Nicola extension. Upon the

Jan 1, 1910