Search Documents

By Jay A. Carpenter

IN six years the construction of Hoover Dam and the power plants probably will have reached the operating stage and this vast new source of power will then be continuously available for industry. The height of the darn will be 580 ft. and the average annual flow of the Colorado River is calculated at approximately 24,000 cu.ft. per sec. If this full head and average flow can be maintained the year round, about one million horsepower will be generated. The U. S. Reclamation engineers, taking into consideration the probable range in flow and head, have set the figure for power contracts at 660,000 firm horsepower, which can be assured at all times of the year. During the months of heavy run-off of water from the Colorado River Basin the power plants should be able to generate the full 1,000,000 hp. capacity of the power plants, so there will be 340,000 excess or secondary horsepower. The cost of firm power at the switchboard will be close to 2.15 mills per kw.-hr., equal to $14.05 per hp.-yr., and the cost of the secondary or off-peak power will be close to 0.8 mills per kw.-hr., or $5.22 per hp.-yr. In no place in the country can such cheap power be obtained today. The electrochemical industry is in a state of flux because the power costs from its old sources have increased so much (to $30 per hp.-yr. at Niagara) that the industries have had to seek new sources, so they have gone to Canada and Norway and built new plants.

Jan 1, 1932

By D. A. Belforti, M. P. Lepie

Spectroscopically pure copper was melted on sapphire plaques in a zydrogen atmosphere. The surface tension of the liquid metal was determined using the sessile drop technique. Measurements were made by direct observation with the aid of a specially const,mcted telescope. The value obtained, 1268 dynes per cm, is compared to that found in the literature. THERE is at this time considerable interest in the use of ceramics for vacuum tubes. The crystalline material is superior to the more conventional glass in mechanical strength, chemical inertness, dielectric properties, ability to withstand high temperatures, and so forth. However, ceramics are much more difficult to seal hermetically with metals than are the glasses. For this reason an investigation was undertaken to determine the wetting and adhesion of metals to ceramics. The sessile drop technique offers a convenient means at elevated temperatures for measuring liquid surface tension, wetting angle, density, spread- ing coefficient, and work of adhesion. Thus, from the contour of a drop of liquid at rest on a solid surface one can obtain a quantitative evaluation of the degree to which the two substances will bond. To this end a special apparatus was constructed so that various molten metals could be observed. Standardization of the apparatus was done initially by measuring the surface tension of copper since this is well documented in the metallurgy literature. Although there are many methods available for the measurement of surface energy,'+ the sessile drop technique has been used most extensively for molten metals and ceramics.5"' Fig. 1 illustrates the dimensions to be measured. From these values, the surface tension of the liquid can be obtained using the Bashforth and bdams' equation and tables.

Jan 1, 1963

By Albert Sauveur

(Winces-Barre Meeting, June, 1911.) THE instrument about to be described meets so perfectly the special needs of the metal microscopist that there seems to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.-The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement' affords free space below the objective for the examination of large specimens of metals, such as full rail-sections, without detracting in the least from the value of the instrument when applied to the examination of the usual small specimen, as explained later. Many metal microscopists frequently have to examine bulky specimens, and this is altogether impossible with the ordinary microscopes as well as with the special metallurgical microscopes which have been designed and described from time to time. Recourse must be had to all sorts of makeshifts for the proper support of large specimens, or, more often, the microscopist gives up the attempt altogether, or else resigns himself to the cutting of the bulky samples into small pieces to -be laboriously polished and separately examined. It is believed that an instrument permitting the examination of large as well as of small specimens with equal ease and accu-

Dec 1, 1911

PICK AND SHOVEL CLUB, CASE SCHOOL OF APPLIED SCIENCE The last meeting of the year of the Pick and Shovel Club of Case School of Applied Science was held on May 20, 1919. The speaker, Dr. Zay Jeffries, gave a very instructive and interesting talk on the Metallography of Non-ferrous Metals. The club has had a very successful year in spite of the loss of a few months time through the S. A. T. C. Among the speakers for the year were Dr. F. R. Van Horn, Dr. C. H. Fulton, and Dr. W. R. Veazey of our school; Dr. E. S. Moore of Penn. State College; Dr. Ansel St. John, of the National Carbon Co.; and Mr. V. S. Bidle, of the W. S. Bidle Co. The graduating members wish the club the best of success for the coming year. BERTRAND R. WARMELING, Secretary.

Jan 7, 1919

By G. M. Webster, G. E. Dawsongrove

The use of percussion-type side-wall cores as an aid in detection and evaluation of hydrocarbon shows and in examination of rock properties has become increasingly popular in recent years. Sidewall coring has an advantage over normal bottom-hole coring methods in that the zones may be surveyed with the electric log prior to selection of sample depths. This allows an efficient sampling of all zones of interest, a procedure not possible with bottom-hole coring techniques unless the costly procedure of continuous coring is utilized. Percussion sidewall coring presently provides the most rapid and lowest cost method of obtaining sidewall cores. It has been recognized for some time that certain discrepancies exist between core analysis data obtained from percussion cores and data obtained from other types of core Samples. This paper presents existing field and laboratory data that were available to the authors. Several examples of comparative core analysis data obtained from various fields are presented along with photomicrographs of thin sections of conventional and percussion cores. The results of this investigation are presented to throw more light on the possible disturbed condition of percussion sidewall cores. SAMPLE DISTURBANCE AND FRACTURING The principal cause of discrepancy between conventional core analysis data and percussion sidewall core analysis data is believed to be the shattering and re-adjustment of the grains due to the large impact shearing forces produced by mechanics of percussion coring. Figs. 1 through 5 are photomicrographs of thin section slides of formation samples obtained by means of diamond cores, conventional cores, and percussion sidewall cores. Figs. 1 and 2 show samples of the

By William Waters Van Ness

The Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively reccnt date, were carried out in the neighborhood of the village of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E—W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposcd to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Jan 1, 1909

R. B. T. KILIANI, Denver, Colo. (written discussion *).-Mr. Len-nox's paper is decidedly interesting in that he shows that a field exists for the Chilean mill, in which its efficiency compares favorably with that of more modern grinding devices. The figures he has given clearly indi-cate that a coarse feed is conducive to higher efficiency than the fine feeds which the Chilean mill has usually been called upon to grind. The fact is also apparently indicated that operating the Chilean mill in closed circuit with a mechanical classifier results in still higher efficiency, and that in such cases the percentage of returns should be kept below 100 per cent. to obtain best results. It would be interesting to see the results of further tests with what Mr. Lennox calls "Mixed Feed," since the data given in Table 4 seems to' point to the fact that a mixed feed,

Jan 12, 1919

By Frank F. Aplan

INTRODUCTION Coal is a solid, combustible mineral substance resulting from the degradation and alteration of vegetable matter largely in the absence of air. In this natural process of coalification, some non-combustible mineral matter is always associated with the combustible material. Coal preparation or cleaning is the process of removing this inert mineral matter from the coal. Preparation is highly successful in removing the large fragments of inert material, but is not very effective in removing the fine inorganic mineral matter intimately associated with the coal. Of the 600 million tons of coal produced in the United States every year, approximately one-half is produced by coal cleaning methods (1). The bulk of this tonnage is cleaned by coarse or intermediate gravity preparation methods (5 inches to 28 mesh, Tyler). Fine cleaning, say, -28 mesh, is done by shaking tables, washing cyclones, and flotation, or, until recently, the fines were either incorporated into the clean coal or simply discarded--not infrequently, the latter. In 1972, only 13 million tons of raw coal were cleaned by flotation in the United States, and from this 8.4 million tons of clean coal were produced (1). The percentage of clean coal produced by flotation in Europe (England, West Germany, Poland, U.S.S.R., etc.) is substantially higher. However, coal flotation has grown rapidly in the United States from only a few plants in 1950 to 31 in 1960 (2) and 66 in 1970 (1). Virtually all new preparation plants incorporate flotation into their basic flowsheet. The essential difference between ore and coal flotation is that for ores the entire tonnage is ground to flotation size, whereas for coal

Jan 1, 1976

By R. E. Gilmore

This paper is a revision of a former paper published in mimeograph form by both the Canadian and American coal classification committees, and is now presented for the purpose of acquainting those interested with the present status of coal classification in Canada. The classification employed for "Customs purposes" is detailed, and the classification schemes from which the customs classification was derived are reviewed and discussed. The activities of the Canadian coal classification committee, namely, the Associate Committee of Coal Classification and Analysis of the National Research Council, is also reviewed. Reserves, Production and Uses of Canadian Coals The total coal resources of North America are estimated to be 69 per cent. of those of the world, and of this portion, the distribution is 52 per cent. for the United States and 17 per cent. for Canada. Accordingly, Canadian coal resources amount to approximately one-third of those of the United States, and one-sixth of those of the world. As for the geographical distribution, the bulk of the known coal deposits are in the extreme eastern and western portions of the country. Employing the usual, more or less loosely defined, designations for the different classes and subclasses of coal, the distribution of the Canadian coal resources, according to provinces, is as follows: Maritime Provinces: Nova Scotia and New Brunswick Bituminous and semibitu- minous coals. Ontario (northern part).............................Lignite. Saskatchewan, (and Manitoba)....................... Lignite. Alberta and British Columbia........................ Lignites, subbituminous, all kinds of bituminous, semibituminous and semianthracite coals. Of the total reserves, roughly 92.5 per cent. is credited to the noncok-ing lower rank subbituninous and lignite groups, the bulk of which are

Jan 1, 1930

By Edward Keller

In order to conduct intelligently the sampling of copper of various forms and grades, solid or in molten furnace-charges, a knowledge of this subject is essential. Yet figures and tests have been persistently withheld from publication, and the books at our command give us little or no information in this regard. This gap in our copper-literature has led to a series of experiments, the results of which are given below. Nearly all gold- and silver-bearing copper, destined for shipment, is cast into the form of bars or pigs. For the sampler, the question arises, Does copper, so cast, remain homogeneous ? If it does, sampling should present no difficulties; but, from experience, we know that this is not the case, and we are thus led to study the behavior of the precious metals arid impurities in copper when the latter changes from the molten to the solid state. For the purpose of the experiments here described, all available grades of copper were selected, and all of them mere subjected to the same conditions, an important requisite for proper comparison. The molten copper obtained directly from reverberatory- and blast-furnaces was cast in a cast-iron mould, the sides and bottom of which were 1 inch thick, and would, therefore, give the copper a fair length of time to chill. The inside dimensions of the mould, and, consequently, of the block of copper obtained, were: length, 10 inches; width, 9 inches; and depth, 5 inches. Fig. 1 illustrates the method employed to obtain samples from these blocks. A was cut away, and the face so produced BALTIMORE COPPER WORKS,

Jan 1, 1898

By Wallace E. Johnson, Leslie R. Hill

As part of a continuing study of intense energy effects on the earth, such as explosive cratering for Plowshare, large scale hydro- dynamic computer codes which numerically integrate the two-dimensional mass, momenta, and energy conservation equations have been adapted for use on geological materials. Experimentally determined nonlinear dynamic equations of state and constitutive equations governing material strength are incorporated into a two-material Eulerian code, DORF. With the use of this code, impact studies have been made of projectiles with arbitrary shapes in the r,z cylindrical plane normally incident on semi-infinite half-space targets. The impact of projectiles on rocks has been studied empirically and experimentally; however, this paper employs a theoretical approach. Particular examples selected involve the impact of aluminum and iron projectiles on oil shale at velocities of 0.5 and 1.0 cm/µsec. These studies offer a quick and economic means to edit quantities unavailable in an experiment and to independently study the effect of varying parameters such as material shape, density, and strength, and impact velocity. Results reveal early time agreement with experimental high-speed photography as seen in the bowl-shaped crater and spray. Initial impact pressures at the projectile-target contact are in close accord with the one-dimensional Rankine-Hugoniot relations for the impact of dissimilar materials. These equations require local continuity of pressure and particle velocity across the interface and were found to hold locally, quite independent of projectile shape. Essentially all projectile energy is transferred quickly to the oil shale target (tens of microseconds). Over 75% of the original kinetic energy

Jan 1, 1971

By H. S. Gieser

THE flotation of oxidized silver, ores offers an interesting problem to the operating metallurgist, who has to treat this material. The advances made in the art of selective flotation by the use of newer collectors with accelerating and inhibiting reagents suggests that there should be something to help to decrease tailing losses. For many years there was no working hypothesis, so the subject was approached more or less in the dark, but with the publication of a paper by Taggart, Taylor and Ince1 giving results of flotation tests with many organic compounds and presenting a tentative theory, a better foundation has been laid and henceforth progress should be more rapid. Over a period of one and one-half years there was much experimentation with flotation of oxidized silver ores at El Tigre, Sonora, Mexico. The material coming to the mill was straight sulfide ore in a silicified rhyolite gangue, the ore minerals being sphalerite, galena, pyrite and tetrahedrite. This came largely from the lower levels of the mine. With the approaching exhaustion of these orebodies, attention was turned to oxidized ores left behind during higher prices of silver. Of late oxidized ore has been at times 25 per cent. of mill tonnage. Aerofloat 25, in considerable quantity, together with ethyl xanthate, has been used in the mill. The former raises large quantities of "insoluble" or gangue, which is difficult to reject when the density of the tailing pulp approaches 33 per cent. solids, as it did during periods of water scarcity. The mill tailing at times contained as much as 5 oz. of silver on a 32-oz. mill head.

Jan 1, 1931

Jan 1, 1947

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve-the error area, probable error, and imperfection value-have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Conference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yancey and Greer6 observed that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis.

Jan 12, 1957

By E. J. Schmitz

The mining of the Triassic coals of the Richmond basin has been carried on, upon a larger or smaller scale, for more than a hundred years. Notwithstanding the close proximity of the field to a large city and to tide-water, assuring both a good home-market and cheap transportation, and notwithstanding the good quality of the fuel and the great thickness of the principal bed developed and worked, operations in this field have been conducted with but limited success. The basin comprises about 189 square miles, being from 24 to 31½ miles in length by 5½ to 10 miles in width. Not much more than one-tenth of this area has been explored in a practical and efficient way, and not over 1200 acres have been worked near and along the outcrops or edges of the coal. The practical mistakes which have been committed undoubtedly in a number of the mine-operations of the past, do not alone explain the unsatisfactory success and progress of the industry of this field ; nor can it be ascribed to the lack of local enterprise. Other reasons have to be looked for; and, as a principal one, the irregularity and the faulted conditions of the coal deposits must be pointed out. As a second cause, the indifference of the State government, which leaves the development of the field entirely to private enterprise, instead of aiding it by systematical and practical geological investigations, deserves to be mentioned. Nothing has been done by the State since the excellent work done more than fifty years ago by Professor Rogers, who could not at that time enter into the details of such

Jan 1, 1895

By F. T. Lee

Directional dependence of strength and deformation properties of the Mount Waldo granite pluton in southeastern Maine is controlled by joints and microfractures whose orientations are linked to flow- induced alignment of microcline crystals. Longitudinal and cross joints which formed during cooling of the mass, as well as much younger sheeting fractures, are commonly associated with subparallel, discontinuous microfractures. The orthogonality of microfractures (open, closed; filled, unfilled; bubble planes) establishes the ease of splitting of the granite. The easiest splitting direction (rift) is subhorizontal, the second easiest direction (grain) is parallel to the cross joints, while the direction of least easy splitting (hardway) is parallel to the longitudinal joints. Static and dynamic measurements made in the field and laboratory established that structural features are responsible for the marked stiffness anisotropy of the granite. In the central part of the pluton the static Young's modulus in the north-south direction averages 31.1 GPa, and 20.9 GPa in the east-west direction; the stiffer direction being parallel to the long C-axes of microcline phenocrysts and microfractures as identified in outcrop, core samples, and thin sections. Vertical downhole sonic measurements of dynamic moduli ranging from 2.5 to 16.2 GPa appeared to be anomalously low when compared to the static horizontal values. However, the field sonic values were confirmed by laboratory sonic pulse testing of oriented cores. The field results reflected closely spaced layers of open horizontal microfractures. Those deformation and strength properties that are closely tied to bubble planes, filled microfractures, and microcline orientation could be extrapolated to greater depths with good hope of success.

Jan 1, 1984

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Mar. 10, 1916 to Apr. 10, 1916: R. C. Blanchard, London, England. George H. Packard, Boston, Mass. F. Lynwood Garrison, Philadelphia, Pa. Harvey B. Small, Mangangue, Colombia, S. A. S. A. Horton, Altoona, Pa. H. De Witt Smith, Kennecott, Alaska. J. S. Lane, New York City. Richard Tarantous, Terlingua, Tex. Harry T. Mercer, Painesdale, Mich. S. A. Taylor, Pittsburgh, Pa. A. L. Blomfield, for many years in the employ of Bewick, Moreing & Co. as metallurgist, and for the last eight years mill superintendent of the Golden Cycle mill at Colorado Springs, has become associated with The Dorr. Company as consulting metallurgical engineer, with headquarters at Denver. He retains his connection with the Golden Cycle mill as general superintendent.

Jan 5, 1916

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, killed in action. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service. Hall, William T., Capt., Royal Flying Corps, killed in action. Heine, Bernhardt E., Lieut., Aviation Service, killed at Fort Sill, Okla., Aug. 10, 1918. Irving, John Duer, Capt., 11th Engineers, A. E. F., died while on active service in France on July 26, 1918.

Jan 9, 1918

By B. Wilshire, W. J. Evans

The high-temperature creep properties of nickel, zinc, and iron have been determined over a range of stresses. The creep strain, E, was found to vary with time, t, as: where e0 is the instantaneous strain on loading, ET the total transient creep strain, $ the steady creep rate, and m is a constant relating to the rate of exhaustion of transient creep. Deviations from this relationship occurred during the initial 10 to 15 pct of the transient stage. These deviations result in the initial creep rate, go, calculated as (m . ET + es), being considerably lower than those obtained by measurements on the creep curve. For all materials, the initial creep rate, the constant m, and the duration of transient creep are all related to the steady creep rate. These relationships suggest that transient and steady-state creep should not be regarded as distinct stages.

Jan 1, 1969

By Arthur Phillips

THE progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yield-ing supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with par-ticular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weerts1 recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150° and 225° C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler

Jan 1, 1934