Search Documents

By Guilherme Liziero Ruggio da Silva, Iara Patricia Vieira de Oliveira, João Ricardo Denicolo Braga, Paulo Santos Assis, Lorena Cristina Amorim Moura

Nos últimos anos diversos trabalhos evidenciam a possibilidade de utilização de small coque como constituinte da carga metálica dos altos-fornos, visando a redução na temperatura da zona de reserva térmica. Esse trabalho avalia a viabilidade técnica, em escala laboratorial, da produção de um determinado small coque altamente reativo, através da adição de 2 catalisadores: pellet feed e cal virgem totalizando 3% em massa, em sua superfície. Foram realizadas caracterizações químicas dos catalisadores por meio de Fluorescência de Raios-X (FRX) e avaliados os impactos destas adições sobre CRI (Coke Reactivity Index) e CSR (Coke Strength after Reaction) das amostras produzidas. Os resultados mostraram aumentos acima de 2% na reatividade do small coque, tanto para a adição de cal virgem quanto para pellet feed, porém mais significativo para a adição de cal virgem, comprovando que a técnica de Pós-adição de catalisadores da reação de Boudouard no small coque, pode ser uma alternativa para redução de custo e emissões de CO2 no Alto-Forno.

Oct 1, 2019

By Breno Totti Maia

Due to operational conditions and locations, BOF suffers variations in important parameters whose effects on the liquid bath are usually neglected. The present paper investigated two aspects: inner BOF pressure and oxygen temperature in the stagnant reservoir. The results have shown that oxygen temperature changes properties like density and velocity but has small influence on jet penetration. The BOF inner pressure has significant influence on jet penetration and creates a new challenge regarding nozzles dimensions considering overexpanding and underexpading jets.

Oct 30, 2017

By João Batista Ribeiro Martins, Érica Simões Rodrigues, Ramiro da Conceição do Nascimento Júnior, Marcos Tadeu D’Azeredo Orlando

In order to guarantee the quality of the sinter and process control some measurements are made such as RDI and FeO (Fe2+). However, the behavior of sinter during reduction in the blast furnace is not always understood, when it is analyzed only metallurgical, physical and chemical quality. Therefore, it is necessary to find alternative techniques to understand more this behavior. In this work four experimental trials were performed to obtain sinter samples with different FeO (Fe2+) contents. Optical microscopy was performed to identify and quantify the phases in sinter and to evaluate the magnetic behavior of each one, the Magnetic Susceptibility technique was used. The results obtained between Optical Microscopy, Magnetic Susceptibility and quality parameters were compared and then was identified that Magnetic Susceptibility may be an alternative to help the understanding of sinter behavior in Blast Furnace.

Oct 1, 2019

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Guilherme Geada Sampaio

Uma linha contínua não só melhora o conforto aos usuários, mas também melhora as condições de desgaste, fadiga e manutenção dos equipamentos ferroviários. Porém, os parâmetros de soldagem devem ser bem especificados e controlados de forma a obter uma junta soldada adequada. Este trabalho oferece uma revisão geral sobre as características básicas de uniões aluminotérmicas de forma a subsidiar a avaliação e melhoria no desempenho de soldagem aluminotérmicas de trilhos, realizada em um outro trabalho também sendo apresentado neste Congresso.

Aug 16, 2017

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018

By Giulio Antunes de Medeiros, Leonardo Martins Silva, Giselle de Mattos Araújo, Rayla de Souza Caldas

To analyze the direct reduction of self-reducting briquettes producted with different electric arc furnace dust contents, three sets of homogeneous mixtures were produced with elephant grass biomass, iron ore, cement and furnace dust in increasing levels, which were submitted to thermogravimetric tests in muffle furnace and TGA furnace at variable temperatures and times. The curves of degree of reduction were obtained and the reduced briquettes were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the reducibility of the agglomerates is diminished by the increase of furnace dust, with variations of this result at higher temperatures. The observed microstructures were spherical particles, porous structure or whiskers. Based on XRD results, it was considered probable that the decrease of the degree of reduction with the increase of furnace dust content is related to the reaction between hematite and zincite, which is expected to be controlled by zinc diffusion.

Oct 1, 2019

By Maria do Socorro da Silva

Aços inoxidáveis são aços caracterizados principalmente por sua alta resistência à corrosão em diversos ambientes. Essa característica advém da formação de uma camada de óxido de cromo. A classe de aços inoxidáveis superausteníticos é derivada dos austeníticos pela adição de elementos de liga. A temperatura do ambiente de trabalho pode favorecer a formação de precipitados que podem afetar as propriedades mecânicas e de resistência à corrosão desses aços. Em decorrência da quantidade de Mo, Ni e Cr ocorre precipitação de fases secundárias, sendo mais comuns as fases sigma (s) e qui (c). Para caracterizar a microestrutura e formação da fase s nos superausteníticos, foram realizados os seguintes tratamentos térmicos de solubilização: 1170oC (para formação da maior fração volumétrica da fase s) e 1210oC (para menor fração volumétrica da fase s) por 2h. Foram realizadas caracterizações por meio das técnicas de microscopia óptica e eletrônica, assim como a utilização das técnicas de análise por energia dispersiva de raios-X (EDX) e dispersão de elétrons retroespalhados (EBSD). Os resultados obtidos foram comparados ao estado como recebido do material (bruto de fusão). Verifica-se a presença da fase s em todas as condições, havendo diferença quanto a fração volumétrica em função do tratamento aplicado.

Aug 16, 2017

By Vitor Vianna de Castro Moreira, Danilson Gonçalves de Melo e Silva, Gabriel Augusto da Fonseca

The present work aims to describe the changes made in the operational procedure of the reheating shell furnace, of the hot-rolling of seamless tubes line at Barreiro Plant of VSB, during non-production periods, focusing on reducing natural gas consumption. According to the previous procedure, the furnace was kept at 750°C on these periods, using the main burners. With the new procedure, the furnace is naturally cooled, maintaining only the auxiliary burners with a pilot light turned on, without worrying about the conservation of temperature. Subsequently, the furnace is heated with a rate of 150 ºC/h until it reaches the setpoint temperature of production. This procedure change was successful and didn’t cause operational and security problems. The minimum stoppage time needed for the natural cooling to be economically favorable is 6 hours and 30 minutes. The new procedure reduced the natural gas consumption in 4.500 Nm³, considering 24 hours of stoppage, achieving an estimated annual economy on the thermal energy costs of R$440.000,00 in 2019.

Oct 3, 2019

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Eltton de Sousa Veras

Entendendo-se a complexidade e o impacto da etapa de Perfuração e Desmonte de Rochas nos processos unitários subsequentes, foi iniciado um projeto para otimização do planejamento e execução desse processo. Dessa forma, foi desenvolvido um projeto para auxiliar no planejamento e execução das malhas de perfuração utilizando o sistema High Precision Drill System (HP-DS). Foi realizado um levantamento em campo para comprovação dos ganhos potenciais de redução de custo e aumento de produtividade, sendo resultados expressivos do ponto de vista financeiro, operacional e de segurança, possibilitando uma redução potencial de 15,8% (percentual de metragem que não agrega valor) de metros perfurados sem comprometer o grau de fragmentação especificado para as operações unitárias de lavra. A eliminação dessas perdas representaria uma redução potencial de custos na ordem de 20 milhões de reais.

Oct 30, 2017

By Ernesto Furtado de Mello Neto, Eliezer Thuler, Claudio Vano Nunes, Carlos Alberto Cristofari

The Brazilian steel industry is dealing an adverse scenario with direct competition from global emerging markets. In this scenario, the need to improve asset operational performance, makes complex studies involving technical knowledge and asset life behavior, become important tools to support companies strategic accomplish. These studies allow consider performance, costs and operational risks relationship in the decision make process. The Asset Management approach support these studies in order to observe the whole asset life cycle, understand value chain through all company process and optimize the asset economic life. In this context, the present technical work has the purpose to support asset management decision making regarding ArcelorMittal Vega cold rolling drive motors, through the motors fail behavior modelling and estimated the risks involved in asset management decision. Through the Reliability, Availability and Mantenability (RAM) analysis, simulations were performed considering the failure, repair cost data and investments to build options to mitigate the operational risks.

Oct 9, 2019

By Luiz Gustavo Franco Amaral

The recent tragedies that occurred in Brazilian territory had a greater impact than that presented in the major newspapers and led an entire industry to question the technology and techniques that were previously practiced in the mining industry. With this, there is the prospect of new projects and innovations in the most varied branches of engineering. This publication presents computational technologies to support the decision making of engineering projects aimed at the mining sector and explores the benefits obtained from the use of current technologies in the mining sector. Recent works are referenced in order to propagate not only the methodology employed in these researches, but also to provide the reader with an overview of the industry and companies that invest in technology to support their decision making in the most diverse projects gains on products and processes obtained through this practice.

Oct 3, 2019

By Rudi César Comiotto Modena, Gabriel de Castro Moreira, Diego Machado Marques

The definition of geological/geostatistical domains is the first step in building a mineral resource model. A suitable division for these domains requires some prior knowledge about the deposit geology and can be supported by a careful statistical analysis. It is crucial that data with similar characteristics are grouped together, to avoid the mixing of statistical populations, defining the so-called stationary domains. In order to assist in this definition, two unsupervised clustering algorithms were applied: Otsu and K-means. The first one is widely used in image segmentation and it is based on the exhaustive search of the data to determine the best threshold for separating them. K-means is one of the most used techniques in machine learning, and it is based on the iterative analysis of the statistical distribution. Clustering algorithms may present some shortcomings when applied to geological data, since they are based on pure statistical analysis, not considering spatial distribution or data location. Choosing the most appropriate number of domains can also be challenging. Some methods for defining the best number of groups are presented, based on the analysis of variances between/inside groups, supported by indicators variography in order to verify this definition.

Oct 3, 2019

By Lidiane da Paixão Carvalho

Foi estudada uma forma de reduzir o custo de produção de aços que atendem a norma NBR 6656 LNE 38 (ou LNE 380) na Companhia Siderúrgica Nacional (CSN). Esses materiais são utilizados em peças de conformabilidade crítica principalmente para indústria automotiva. Na CSN, o Forno Panela tradicionalmente faz parte da rota obrigatória de fabricação desses materiais constituindo um “gargalo” de produção. Efetuou-se uma análise da composição química, então empregada para os aços e das propriedades mecânicas resultantes, e então se buscou uma nova composição que atendesse a norma e que permitisse outra rota de produção. Percebeu-se que uma redução no teor de manganês em relação ao normalmente utilizado propiciava uma melhor adequação à norma, além de permitir o uso de uma rota alternativa que maximizava a produção e permitia reduzir custos.

Jul 30, 2018

By Antônio Augusto de Morais Piau, Miguel Araujo de Vasconcelos Filho, Bruno Mynelly Galdino de Sousa

Sludges and dusts generated by steel mills usually cause environmental problems and has a high cost solution. This presentation offers a different aproach to the problem with a solution that not only solves the enviromental issue but also brings great savings to the mill. This technology, reuses dusts and sludges in the sintering process, after they are mixed to the right composition.

Oct 1, 2019

By Thamiris Auxiliadora Gonçalves Martins, Karen Espina Gomes, Amilton Barbosa Botelho Junior

The present work aims at the synthesis of nanoparticles of copper by chemical reduction in microwave oven. The solution used comes from the selective copper precipitation of the lateritic nickel leachate. The copper solution (20mL) was placed in a beaker, and 2mL of 100g/L ascorbic acid and 20mL of 20g/L sodium citrate were added in that order and at room temperature. The pH of the mixture was corrected with 1M sulfuric acid or 2M sodium hydroxide. Then the mixture was placed in a microwave oven. The effect of pH, time and microwave power were evaluated. The morphology, composition and size of the particles were verified in Scanning Electron Microscopy with Energy Dispersion Spectroscopy (SEM/EDS). Results showed that the particles formed had no nanometric size. This may have occurred because the reducing action of ascorbic acid together with sodium citrate generates a very rapid reduction rate, which makes it impossible to form particles on a gauge scale. Particles synthesized at pH 4, after 4 minutes of reaction with 1000W of power presented particles with spherical morphology and only copper in the composition.

Oct 3, 2019

By Wellington Ribeiro Moreirar, Anderson Willian Henrique Santini, Lívia Mara Cândido, Adriano Raimundo Totour

Rejects generated in mining projects usually do not have associated economic value. Most of the ore beneficiation processes occur by wet process with a higher fraction of water and ultrafine granulometry, which makes it difficult to dispose of these wastes. In 2013, studies with new tailings treatment and filtering technologies were initiated with the objective of eliminating the disposal of the residue generated in the industrial process to wet in dams. In this context, we tried to evaluate an alternative for the dewatering of the sludge and the tailings, aiming at their disposal in piles. Essentially, we sought to consolidate the application of the high-pressure filtration technology for the effluent dewatering, in order to allow its transport and its disposal in a sustainable way. The studies performed in a pilot filter showed good performance and allowed the industrial implantation. The studies and geotechnical indications of composite tailings (flotation and sludge) make it possible to dispose of the tailings in piles due to their better values of humidity, which allows them to be safely stacked.

Oct 3, 2019

By Weimar Silva Castilho

A influência do tempo de encharque criogênico no amortecimento da liga Ni-43,9%Ti foi investigada. Por meio da técnica de excitação por impulso determinou-se essa propriedade de amostras submetidas a diferentes tempos de encharque criogênico a -196oC. Observou-se que o amortecimento sofreu aumento de até 119% para corpo de prova submetido ao encharque criogênico por 24 horas.

Aug 16, 2017